Spektrum DX2E 2Ch DSMR Surface Radio w/SR310 Bedienungsanleitung

Spektrum Funkgesteuertes Spielzeug DX2E 2Ch DSMR Surface Radio w/SR310

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Spektrum DX2E 2Ch DSMR Surface Radio w/SR310 (6 Seiten) in der Kategorie Funkgesteuertes Spielzeug. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
1
SPEKTRUM DX2E USER GUIDE
EN
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of
Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential harm when operating
this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no
possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility
of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and
serious injury OR create a high probability of superficial injury.
INSTALLING THE
TRANSMITTER BATTERIES
BATTERY LED MONITOR
ÂŽ
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.
Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some
basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to
the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with
incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This
manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and
warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to
ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards,
but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or
Spektrum.
Age Recommendation: Not for Children under 14 years. This is not a toy.
NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles. Horizon Hobby
disclaims all liability outside of the intended purpose and will not provide warranty service related thereto.
WARRANTY REGISTRATION
Visit www.spektrumrc.com/registration today to register your product.
Solid Green Battery is good (Above 4V)
Flashing Green Battery voltage is critically low.
Replace batteries (below 4V)
2SPEKTRUM DX2E USER GUIDE
EN
RECEIvER COMPATIBILITy
The DX2E is compatible with all Spektrum
™ DSMR™ and
DSM2ÂŽ receivers.
RECEIvER CONNECTION
AND INSTALLATION
TyPICAL ELECTRIC INSTALLATION
TyPICAL GAS INSTALLATION
Install the Receiver in your vehicle using double-sided foam
servo tape. Foam servo tape will hold the receiver in place
and help isolate it from vibrations. Mount the antenna up
and away from the vehicle in an antenna tube. The higher
up the antenna is, the better signal it will receive.
CAUTION: Do not cut the antenna.
BINDING A RECEIvER
Binding is the process of programming the receiver to
recognize the GUID (Globally Unique Identifier) code of a
single specific transmitter. When a receiver is bound to
a transmitter, the receiver will only respond to that specific
transmitter. The DX2E and SR310 are bound at the factory,
but if you need to rebind for any reason, please follow
these steps:
1. With the receiver off, insert the bind plug into the BIND
port on the receiver.
2. Power the receiver through any other port. The green
LED will flash continuously, indicating the receiver is
in bind mode.
3. With the steering wheel and throttle trigger in the desired
preset failsafe positions (see the Failsafe section on this
page for more information), press and hold the bind
button and turn on the transmitter. The green LED on the
front of the transmitter will flash within three seconds,
indicating the transmitter is in bind mode. Release the
bind button when the green LED flashes. Continue to
hold the failsafe positions until the binding process
is complete.
4. The LED on the receiver will glow solid when the
transmitter and receiver are bound.
5. Remove the bind plug and store it in a convenient place.
You must rebind when:
• Differentfailsafepositionsaredesirede.g.,whenthrottle
or steering reversing has been changed.
• Changingreceivertypese.g.,changingfromaDSM2
receiver to DSMR receiver.
• Bindingthereceivertoadifferenttransmitter.
FAILSAFE
Failsafe positions are also set during binding. In the unlikely
event that the radio link is lost during use, the receiver will
drive the servos to their preprogrammed failsafe positions
(normally full brakes and straight steering). If the receiver
is turned on prior to turning on the transmitter, the receiver
will enter failsafe mode. When the transmitter is turned on,
normal control is resumed. For more information on setting
the failsafe, refer to the Binding a Receiver section above.
Receiver
Steering Servo
Throttle Servo
Battery
Battery To Motor
Electronic
Speed Control
Steering Servo
Receiver
Throttle Port
Steering Port
Bind Plug
Antenna
Bind Button
3
SPEKTRUM DX2E USER GUIDE
EN
SERvO REvERSING
If a right steering command does not result in the wheels
turning right (and vice versa), the channel may need to be
reversed. To reverse a channel, switch the position of the
correlating switch—“N” is for normal, “R” is for reverse. You
can use a small screwdriver to move the switch if necessary.
STEERING TRIM
The steering trim dial is used to adjust the steering trim when
the wheel is centered. Rotating the dial changes the steering
trim (the steering at rest position). Normally, the steering trim
is adjusted until the vehicle tracks straight.
ThROTTLE TRIM
The throttle trim dial is used to adjust the throttle trim when
the throttle stick is released (neutral position). This is typically
used to adjust the brakes. Rotating the dial causes the
throttle trim (the throttle position at rest) to be changed.
ChANGING ThE TRAvEL ADjUST
SETTINGS
The travel function supports precise endpoint adjustments in
each direction for the steering and throttle channels.
1. Hold the trigger in the full brake position and the steering wheel
in full right position while powering on the transmitter. The LED
flashes rapidly, indicating the programming mode is active.
2. Throttle End Point: Hold the trigger in the full throttle position.
Turn the TH TRIM knob to adjust the full throttle end point.
3. Brake End Point: Hold the trigger in the full brake position. Turn
the TH TRIM knob to adjust the full brake end point. Return
the trigger to the center position.
4. Left Steering End Point: Hold the steering wheel in the full left
position. Turn the ST TRIM knob to adjust the left end point.
5. Right Steering End Point: Hold the steering wheel in the full
right position. Turn the ST TRIM knob to adjust the right end
point. Return the steering wheel to the center position.
6. Power off the transmitter to save the travel adjust settings. The
minimum Travel is 75%, and the Maximum travel is 150%.
The default travel settings are 125% steering and
100% throttle.
IMPORTANT: If the travel is changed on the DX2E, you must
rebind and calibrate AVCÂŽ Receivers.
STEERING RATE AND GAIN CONTROL
Steering rate (also known as dual rate) allows on-the-fly
steering travel adjustments to be made using the ST Rate
dial. Steering rate limits the amount of travel of the steering
servo. The steering rate cannot be greater than 100%.
When the DX2E is bound to a DSMR AVC receiver, the ST
RATE knob controls the sensor gain value. Turn the knob
counterclockwise to reduce the gain or clockwise to increase
the gain.
R.O.S.S. START BUTTON
The transmitter BIND button also functions as a Remote
On-Board Starting System (R.O.S.S.) button. To use the R.O.S.S.
button:
1. Connect the R.O.S.S. system to the AUX 1 port on the
receiver.
2. Press and hold the R.O.S.S. button to activate the system.
SAFETy PRECAUTIONS
• Alwaysensureallbatterieshavebeenproperlycharged
prior to using the model.
• Alwayscheckallservosandtheirconnectionspriorto
each run.
• Neveroperateyourmodelnearspectators,parkingareas
or any other area that could result in injury to people or
damage of property.
• Neveroperateyourmodelduringadverseweather
conditions. Poor visibility can cause disorientation and loss
of control of your model.
• Neverpointthetransmitterantennadirectlytowardthe
model. The radiation pattern from the tip of the antenna
is inherently low.
• Ifatanytimeduringtheoperationofyourmodelyou
observe any erratic or abnormal operation, immediately
stop operation of your model until the cause of the
problem has been ascertained and corrected.
Reverse Switch
Steering
Reverse Switch
Throttle
Steering Trim Dial
Throttle Trim Dial
Steering
Rate Dial


Produktspezifikationen

Marke: Spektrum
Kategorie: Funkgesteuertes Spielzeug
Modell: DX2E 2Ch DSMR Surface Radio w/SR310

Brauchst du Hilfe?

Wenn Sie Hilfe mit Spektrum DX2E 2Ch DSMR Surface Radio w/SR310 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Funkgesteuertes Spielzeug Spektrum

Bedienungsanleitung Funkgesteuertes Spielzeug

Neueste Bedienungsanleitung fĂźr -Kategorien-