Speco Technologies O4VD2G Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Speco Technologies O4VD2G (45 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/45
User Manual
4MP IP Camera
O4VB2/ O4VB2G/ O4VB2M/ O4VD2/ O4VD2G / O4VD2M/ O4VT2/
O4VT2G/ O4VT2M
Please read this manual carefully before operang the unit keep it for further reference and
Important Safeguards and Warnings
1. Electrical safety
All installaon and operaon here should conform to local electrical safety codes.
Use a cered/listed 12VDC Class2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same me; it may result in device damage! The
product must be grounded to reduce the risk of electric shock.
Improper handling and/or installaon could run the risk of re or electrical shock.
2. Environment
Do not expose the heavy stress, violent vibraon long-term exposure water humidity during transportaon, unit to or to and
storage, and/or installaon.
Do not install near sources heat. of
Only install the product environments inside the specicaon operang temperature humidity range. in and
Do not install the camera near power lines, radar equipment other electromagnec radiation. or
Do not block any venlaon enings any. op if
Use all the weatherproong hardware requirement minimize weather intrusion.to
3. Operaon and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor opc component. You can use a blower to clean the dust on the lens surface.
Always use the dry so cloth to clean the device. If there is too much dust, use a cloth dampened with a small quanty of neutral
detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth) may
result in poor IR functionality and/or IR reecon.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
Dome cover is an opcal device, please do not touch or wipe cover surface directly during installaon and use, please refer to the
following methods if dirt is found.
Stained with dirt:
Use oil-free so brush or hair dryer to remove it gently.
Stained with grease or ngerprint.
Use oil-free coon cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and
wipe several mes if it is not clean enough.
Warning
This camera should be installed by qualied personnel only.
All the examinaon and repair work should be done by qualied personnel.
Any unauthorized changes or modicaons could void the warranty.
Statement
This guide is for reference only.
Product, manuals, and specicaons may be modied without prior noce. Speco Technologies reserves the right to modify these
without noce and without incurring any obligaon.
Speco Technologies is not liable for any loss caused by improper operaon.
Regulatory Informaon
FCC condions:
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operaon.
FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protecon against harmful interference. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instrucon manual, may cause harmful
interference to radio communicaon. However, there is no guarantee that interference will not occur in a parcular installaon. If
this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Note:
Before installaon, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the package.
Accessory name
Amount
Network Camera Unit
1
Juncon box
1
Quick Start Guide
1
Installaon Accessories Bag
1
CD
1


Produktspezifikationen

Marke: Speco Technologies
Kategorie: Nicht kategorisiert
Modell: O4VD2G

Brauchst du Hilfe?

Wenn Sie Hilfe mit Speco Technologies O4VD2G benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Speco Technologies

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-