SoundTube IW31-EZ Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr SoundTube IW31-EZ (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
Do not spec or install speaker near support beam, ventilation duct or other
structure that may interfere with speaker function or dispersion.
Warning Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for optimum
audio performance, installer must follow all directions issued by SoundTube Entertainment.
Grille
Installation aid/paint mask
SpeedWingℱ mounting arms
Grille safety clip
Signal wires
Pre-construction bracket (sold separately)
1.
2.
1.
2.
1. Unpack speaker. Leave
paint mask in place until
after speaker is installed or
painting is complete.
4. Unpack speaker. Leave
paint mask in place until
after speaker is installed or
painting is complete.
5. Insert speaker in hole.
Tighten the two clamping
screws. DO NOT
OVERTIGHTEN .
6. If required, attach
seismic restraint system to
the hole in the metal
clamping arm, then to
reinforced structure (safety
cable not included).
2. Use provided cutout
template to mark hole. Use
RotoZip or other tool to cut
hole in wall. Hole size: 4.25
in. (108 mm) tall x 4.25 in.
(108 mm) wide.
4. If required, attach
seismic restraint system to
the hole in the metal
clamping arm, then to
reinforced structure (safety
cable not included).
6. Remove paint mask
unless painting is required.
In that case, follow steps
7-10 when painting is
complete.
10. 12. Done! Done!
8. Attach grille safety clip by
placing the large end of the
clip over snap-t post (1),
then sliding clip until small
end snaps into place around
post (2).
7. Adjust tap switch to
proper setting. Switch is
preset to the highest setting
in the 70.7-volt mode.
1. Nail or screw bracket to
studs.
5. Feed speaker wires
through conduit clamp and
connect with wire nuts. Push
wire nuts into backcan and
ax conduit clamp.
2. Finish installing wall. Use RotoZip or other tool 3.
to cut hole.
3. Feed speaker wires
through conduit clamp and
connect with wire nuts. Push
wire nuts into backcan and
ax conduit clamp.
8. Remove paint mask
unless painting is required.
In that case, follow steps
9-12 when painting is
complete.
9. Adjust tap switch to
proper setting. Switch is
preset to the highest setting
in the 70.7-volt mode.
7. Insert speaker in hole.
Tighten the two clamping
screws. DO NOT
OVERTIGHTEN .
10. Attach grille safety clip
by placing the large end of
the clip over snap-t post
(1), then sliding clip until
small end snaps into place
around post (2).
11. Align tabs on snap-t
grille with slots in bae,
gently press grille into place.
9. Align tabs on snap-t grille
with slots in bae, gently
press grille into place.
Box contents
1 Speaker
1 Grille
1 Paint mask
1 Cutout hole template
2 Wire nuts
1 UL-listed conduit clamp
© 2011 SoundTube Entertainment, Inc. All rights reserved. PN INS-IW31-EZ Rev 09.12.11
IW31-EZ Pre-Construction Bracket Instructions For:
IW31-EZ speaker
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
IW31-EZ Installation Instructions For:
IW31-EZ speaker
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
Install Instructions For:
IW31-EZ speaker
IW31-EZ
Flexible conduit clamp


Produktspezifikationen

Marke: SoundTube
Kategorie: Nicht kategorisiert
Modell: IW31-EZ

Brauchst du Hilfe?

Wenn Sie Hilfe mit SoundTube IW31-EZ benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert SoundTube

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-