Soundstream VR-64HBL Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Soundstream VR-64HBL (23 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/23
2-Din DVD Headunit
Owners Manual
VR-64HBL
EN
2 MonitorDIN 6.2''
Touch screen
DVD/CD/MP3/MP4/USB/SD
AM/FM Radio
Support Android Phone Link
Support Bluetooth
Thank you for using our company multi-media
player! To operate the unit correctly, please
read the operation manual carefully before
using. Keep this operation manual for further
reference.The unit is designed only fo r DC 12V
negative ground operation system. Make sure
your vehicle is connected to DC 12V negative
ground electrical system. Do not connect it to
24V power supply in trucks or buses, or else it
will be damaged. Be sure to connect the
speaker (-) leads to the speaker (-) terminal.
Never connect the left and right channel speaker
wires together or to the vehicle body. The normal
temperature for operation is between -20 and
+60 degree Celsius. Do not work in extreme
high or low temperature and block vents or
radiator panels of the unit, blocking them will
cause heat to build up inside the unit and may
cause damage or fire.
Do not put the device in a moist environment or
water to avoid electric shock, damage and/or fire
due to a short circuit.
This unit can play the following discs (12 cm) and
media les: DVR/RW / WMV / VCD / MP3 /WMA
/ CD-R/RW / JPEG. Please use genuine discs instead
of incompatible discs, or it will damage the device
and/or shorten the service life.
Protecting the monitor
To protect the monitor from damage, do not
operate the monitor using a ballpoint pen or
similar tool with the sharp tip.
Before use
Before use
Cleaning the unit
Caution 3
How to reset the unit 3
Protecting the monitor 2
3
Important notice & precaution 2
Basics
Installation
Trouble Shooting 22
Specication 21
Panel Description 6
Remote Control 6
Operation
Main menu 9
Audio & Video setting 9
Settings menu 10
Radio operation 15
Disc/USB/SD operation 15
Bluetooth operation 17
APP operation 18
AUX IN operation 18
F-Camera operation 19
Phonelink operation 19
Installation 4
Wiring 5
Speaker Connection 4
Parking wiring 4
IMPORTANT NOTICE & PRECAUTIONS
Contents
22
Installation
1. Make sure the ignition i s turned off, and
disconnect the cable from the vehicle battery’s
negative (-) terminal.
You never want electricity running while you
install this 2-DIN car receiver.
2. Before installation, disconnect the wire harness
and the antenna.
3. Attach the brackets on the both sides of the car
receiver with screws as shown as the above figure.
4. Consult with your nearest dealer if installation
requires the drilling of holes or other modification of
the vehicle.
5. Install the car receiver in the dashboard.
6. Connect the wire harness & antenna to the car
receiver being carefully not to pinch any wires or
cables.
7. Install the plastic outer trim ring onto the car
receiver.
8. Reconnect the battery and run through all of the
options on this car receiver to ensure that everything
is working correctly.
9. Particulars will vary widely depending upon the
kind of your car and the car you intend to install it in.
Please choose the correct installation method
according to the actual situation of your car. Always
contact the car dealer or manufacturer if you have
any questions.
Note: The parking wire is connected with brake
signal; for safety, the programs can be seen on
the monitor after braking the car.
Connecting the revising line to taillight on the
car.
After connection, when you start up the reverse
gear, the unit will receive the picture from car
rear view camera.
Parking Wire
Speaker connection
1. Only use groudless loudspeakers
2 Use only loudspeakers of munimum 40 Watt,
using fewer watts may result in damaging
your loudspeakers at higher volumes.
3.Use 4-8 ohm impendace loudspeakers only,
suing higher or lesser inpendance may
damage the unit.
4.Do not use 3-cable loudspeakers and do not
connect the loudspeakers mumis to the car.
The unit is using a BTL circuit and eachloud-
speaker must be connected
with insulated cables according the diagram.
5. Loudspeaker cables and/or optional external
power amplifiers must always be about 30 cm
away from the antenna and/or antenna
extension parts.
Connect the speakers accordind the following
diagram,incorrect connections will damage
the unit or your loudspeakers.
Installation
4


Produktspezifikationen

Marke: Soundstream
Kategorie: Nicht kategorisiert
Modell: VR-64HBL

Brauchst du Hilfe?

Wenn Sie Hilfe mit Soundstream VR-64HBL benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Soundstream

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-