Sony SNC-VB642D Bedienungsanleitung

Sony Sicherheitskamera SNC-VB642D

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sony SNC-VB642D (2 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

85.7 (3 3/8)

Hole for connecting

cables ø40 (1 5/8)

Horizontal maker

Hole for installing

the stand

Unit: mm (inches)

83.7 (3 3/10)

Vertical marker

83.7 (3 3/10)

85.7 (3 3/8)

Ceiling

Wire rope

(supplied)

Camera unit mounting screw

(commercially-available) (4)

Liner

Twice

2-a LAN cable

Overlap at least

half of its width

Tab

10 (1/2) 10 (1/2)

2-b SP terminal / MIC terminal / I/O (Input/Output) cable / BNC

cable

10 (1/2) 10 (1/2)

10 (1/2)

Overlap at least

half of its width

SNC-VB642D SNC-EB642R

Overlap at least

half of its width

2-c Power input cable

SNC-VB642D SNC-EB642R

30 (1 1

)

Heat shrinkable tube Heat shrinkable tube

Wrap this part

two-fold Wrap this part

two-fold

Overlap at least

half of its width

Overlap at least

half of its width

4-696-254- (1)11

Network Camera

SNC-VB642D/EB642R

Installation Manual

Before operating the unit, please read this manual thoroughly and

retain it for future reference.

About the Manuals

Safety Regulations (included)

The Safety Regulations describes notes for the secure usage of camera. Be sure

to read it.

Installation Manual (this document)

Describes the names and functions of parts and controls of the Network Camera,

gives connection examples and explains how to set up the camera. Be sure to

read the Installation Manual before operating.

The illustration of SNC-VB642D is used for example purpose.

Electronic Instruction Manual (Web)

How to control the camera via a web browser ˎ

How to setup the camera ˎ

Operate the camera referring to the guide above after having installed and

connected the camera properly based on the Installation Manual.

Assigning the IP address

1 Download the installer for “SNC toolbox” to a folder from the download

site.

2 Install the SNC toolbox.

Unzip the ZIP file of the downloaded installer.

Double-click “SncToolbox_Setup.exe.” For details on installing and use refer to

the Application Guide.

3 Assign an IP address.

Assign an IP address using the installed SNC toolbox. For details, see “Using

SNC toolbox” – “Assign an IP address” in the Application Guide.

Tip

SNC toolbox stands for Sony Network Camera toolbox.

Location and Function of Part

Front 

 Audio cable

The connector with the longer cable (SP) is used for the line output connector,

and the shorter cable (MIC) is used for the microphone/line input connector.

SP terminal (minijack, monaural) ˎ

Connect a commercially available speaker system with a built-in amplifier.

MIC terminal (minijack, monaural) ˎ

Connect a commercially available microphone. This jack supports plugin-

power microphones (rated voltage: 2.5 V DC).

 I/O (Input/Output) cable

Use for SNC-VB642D only.

This cable is provided with two sensor inputs and two alarm outputs. The wires

of the cable control the following signals.

Color of wire Name

Red Sensor In 1+

White Sensor In 2+

Black Sensor In – (GND)

Yellow Alarm Out 1+

Brown Alarm Out 1–

Green Alarm Out 2+

Blue Alarm Out 2–

For details on each function and required settings, see the User’s Guide.

For wiring, see “Connecting the I/O Cable” (P2).

 Wire rope

When installing the camera on the ceiling or the wall, make sure to attach the

supplied wire rope.

 Sun shield nut

 Front cover

 Power input cable

Use for SNC-VB642D only.

Connect this cable to a 24 V AC or 12 V DC power supply system.

You can screw an extension cable in the connector tip attached at the end of the

cable. Connect GND to the FG terminal (center of 3-pin connector). See

illustration .

 BNC cable

Outputs a composite video signal.

 Ground wire

Ground the camera when you install it.

 LAN cable (RJ-45)

Connect this cable to a hub or computer on the 10BASE-T or 100BASE-TX

network using a commercially available network cable (category 5).

Note

Take care not to trap the cables between the camera and the ceiling or the wall. If

the cable is trapped, it may cause a fire or electric shock due to breaking.

 Sun shield

The sun shield can be adjusted horizontally up to 26 mm (1 1/ inches), as 8

required.

 Camera

 Front cover screw (four positions)

Inside 

 Lens

 POWER indicator (Green)

When the power is supplied to the camera, the camera starts checking the

system. If the system is normal, this indicator lights up.

 HEATER indicator (Green)

The indicator lights up in green when the built-in heater is working normally.

 NETWORK indicator (Green/Orange)

The indicator lights up or flashes when the camera is connected to the network.

The indicator is off when the camera is not connected to the network.

 Mode setting DIP switches

DIP switch function/settings

SNC-VB642D

Switch No. 1 2

VIDEO POWER

Up (ON) PAL PoE+, AC, DC

Down (OFF) NTSC PoE

1 VIDEO (NTSC/PAL) switch (Initial setting: NTSC)

Switches the video output.

After setting the switch, reboot the camera unit.

2 POWER (PoE+, AC, DC/PoE) switch (Initial setting: PoE+, AC, DC)

Change according to the power you are using.

Note

When power is supplied by IEEE802.3af (PoE) equipment, if the switch is set to

PoE+, the camera will not work properly.

When the power is supplied via power supply equipment that complies with

IEEE802.3at (PoE+), an AC power adaptor, or a DC power adaptor, the heater

will not work if the switch is set to PoE. Note that if you use the camera in a low

temperature, the camera may not work.

SNC-EB642R

Switch No. 1 2

VIDEO HEATER

Up (ON) PAL AUTO

Down (OFF) NTSC OFF

1 VIDEO (NTSC/PAL) switch (Initial setting: NTSC)

Switches the video output.

After setting the switch, reboot the camera unit.

2 HEATER (AUTO/OFF) switch (Initial setting: AUTO)

The integrated heater function will be deactivated when it is set to OFF. Be

sure to set to AUTO when you use the camera in cool environment.

 Reset switch

To reset the camera to the factory default settings, hold down this switch with a

point and supply the power to the camera.

 MONITOR output jack

Connect this jack to a video input connector of a video monitor. You can adjust

the camera or lens while looking at the image on the video monitor. After

adjusting the camera or lens, disconnect the cable.

 ZOOM/FOCUS switch

Use this switch to adjust lens’ zoom and focus. Slide the switch lever to select the

desired function.

[W] WIDE: Zoom out

[T] TELE: Zoom in

[N] NEAR: Focus on a nearby subject

[F] FAR: Focus on a distant subject

Hold down the center of the ZOOM/FOCUS switch for a moment to focus

automatically.

 SD card slot

This slot is used for optional SD memory cards.

Image data in the camera can be recorded to a memory card by inserting it into

the slot.

Gently insert an SD card in (see illustration) until it clicks into place.

This unit is only compatible with SD and SDHC memory cards.

Note

For inquiries regarding verified SD memory cards, contact your authorized Sony

dealer.

Back 

 Base stand

 Base screw (two positions)

 TOP mark

 Arm screw

 Arm

 Rating label

Shows the name of this camera and its electric rating.

 Water drain

When installing the unit on a wall, make sure this water drain is not sealed.

Installation

WARNING

If you attach the camera in the height such as the wall or the ceiling, etc.,

entrust the installation to an experienced contractor or installer.

If you install the camera at a height, ensure that the installation location and

its material are strong enough to withstand a weight of 15 kg (33 lb 11 oz) or

more, and then install the camera securely. If the ceiling is not strong enough,

the camera may fall and cause serious injury.

Do not pull on any cables forcefully, as a connection may become loose.

To prevent the camera from falling, make sure to attach the supplied wire rope.

If you attach the camera to the ceiling, check periodically, at least once a year,

to ensure that the connection has not loosened. If conditions warrant, make

this periodic check more frequently.

Deciding the Installation Location of the Camera 

After deciding the direction in which the camera will shoot, make the required hole

(ø40 mm (1

inches)) for the connecting cables using the supplied template.

Then decide the four mounting hole positions to install the base stand.

Mounting screws

The camera stand is provided with four ø4.5 mm (3/ inches) mounting holes. 16

Install the camera stand on a ceiling or wall with screws through four mounting

holes: The required mounting screws differ depending on the installation

location and its material. Use commercially-available screws.

Steel wall or ceiling: Use M4 bolts and nuts.

Wooden wall or ceiling: Use M4 tapping screws. The panel thickness must be

15 mm (5/ inches) or more.8

Concrete wall: Use anchors, bolts and plugs suitable for concrete walls.

Junction box: Use screws to match the holes on the junction box.

WARNING

The required mounting screws differ depending on the installation location and

its material. If you do not secure the camera with the appropriate mounting

screws, the camera may fall off.

Installing the Camera 

1 Pass the cables through the hole for connecting cables made at the

installing surface.

2 Fix the wire rope to the wall or ceiling.

3 Install the camera on the wall or ceiling.

The remaining cable can be incorporated in the space between the base

stand and the mounting surface. (-)

Insert the four screws in the screw holes on the camera stand, and then

tighten the screws to attach the camera.

When installing the camera on the wall, be sure the TOP mark on the camera

stand is at the top.

Refer to “Mounting screws” in section D for screw to be used.

Notes

If you install the camera unit on a ceiling, take adequate waterproofing ˎ

measures to prevent water seepage into the stand.

When installing the unit on a wall, make sure the water drain is not sealed. ˎ

Notes on waterproofing of cable connection area 

Despite the fact that this unit is rated IP66, the cables and/or the connectors

join to the outside are not waterproof. To prevent water ingress from the cables

and/or the connectors, waterproof them with the supplied waterproof tape as

follows. Otherwise, there may be a risk of water entering through the cables

and/or the connectors and shorting the unit or the connectors.

1 Connect all the required cables and the ground wire.

2 To obtain optimal waterproofing, tear off the liner before wrapping,

then stretch the tape to twice its original length. ( -1)

If it is not fully stretched, the waterproofing function of the tape can not be

achieved.

3 Overlap the tape at least half of its width when wrapping. ( -2)

Notes

Do not press the network cable tab down when wrapping it.

When you wrap the power input cable, start from the heat shrinkable tube.

Make sure at least 30 mm (1 1/ inches) of the wire part that is connected to 4

the power supply equipment is wrapped. (2-c)

Since the connector of the power input cable has gaps, wrap the connector

part two-fold.

Make sure at least 10 mm (

ˎ 1/ inches) of the wire part (excluding the power 2

input cable) is wrapped.

Make sure there is no unwrapped part or damage on the tape.

4 After wrapping, squeeze the tape with your fingers at the overlapping

parts so that layers are airtight and fully adhered.

Unit: mm (inches)

Adjusting the Camera Direction and Coverage 

If the MONITOR output jack is used, adjust the camera direction and coverage as

described from steps 1 to 8.

When viewing the image with the LAN cable, adjust the camera direction and

coverage as described from steps 3 to 5.

1 Fully loosen the sun shield nut until the sun shield can be slid to the front

end (when the nut is located at the back hole of sun shield slide slot),

and take off the sun shield.

2 Loosen the four front cover screws with the supplied wrench, and take

off the front cover.

3 First loosen the two base screws with the supplied wrench, then loosen

the arm screw.

To fine adjust, only loosen the arm screw.

4 Adjust the camera to turn the lens in the desired direction.

5 First tighten the two base screws with the supplied wrench, then tighten

the arm screw (tightening torque: 2.0 N·m).

6 Adjust the zoom by the ZOOM/FOCUS switch (W/T).

7 Hold down the center of the ZOOM/FOCUS switch for a moment to focus

automatically.

8 Repeat steps 3 to 7 until the coverage and the focus are determined.

Notes

When adjusting the camera direction and coverage, do not touch the front ˎ

cover waterproof rubber gasket to prevent it from being contaminated,

detached or damaged. Otherwise, water enters the camera.

If you cannot achieve satisfactory focus by holding down the ZOOM/FOCUS ˎ

switch due to the shooting environment, slide the ZOOM/FOCUS switch level

to N/F to focus manually.

Do not turn off this unit as soon as the focus is adjusted. Turn off after five ˎ

minutes have passed since the focus was adjusted.

Distortion might be observed in images shot outside the specified optical ˎ

area.

Attaching the front cover and the sun shield 

1 Check if the waterproof rubber gasket is contaminated, detached or

damaged.

2 Align the four front cover screw holes with the bosses on the camera.

Make sure the TOP mark on the front cover is at the top, then tighten

the four screws with the supplied wrench to secure the front cover.

(tightening torque: 0.4 N·m)

3 Align the back hole of sun shield slide slot with the sun shield nut to

install the sun shield, adjust the sun shield to the desired position, then

tighten the sun shield nut manually.

Adjust the sun shield position as follows:

 Loosen the sun shield nut manually.

Do not loosen the sun shield nut too much, to prevent it from sliding to

the back hole of sun shield slide slot.

 Adjust the sun shield to the desired position horizontally.

 Tighten the sun shield nut manually to secure the sun shield.

Notes

Make sure the waterproof rubber gasket is clean and fits in the groove ˎ

properly. After installing the front cover, make sure the gap between the front

cover and the camera unit is even. Make sure there is no uneven gap or foreign

matter stuck on the gasket. Otherwise, water enters the camera. ( -4)

Poor focus may also be caused by the front cover assembly. Readjust the focus ˎ

using the system menu.

For details, refer to the User’s Guide of the equipment.

When adjusting the factory-set position of the sun shield forward, the sun ˎ

shield or dark vignetting may be observed in the upper sides of the images.

Also, the image quality will be reduced when the IR LED is operating.

Important precautions 

Despite the fact that this unit is rated IP66, this section includes important

precautions to prevent any malfunction caused by condensation and/or water

ingress. Read the precautions below thoroughly before installing the unit.

Make sure that the cables and/or connectors of the unit that join to the ˎ

ones of the installation surface are waterproofed, before you install the unit.

Otherwise, there may be a risk of water entering the unit through these cables.

Make sure to waterproof the cables and/or connectors with the supplied ˎ

waterproof tape as stipulated in this manual. Otherwise, there may be a risk of

water entering and shorting the unit. For details, see “Notes on waterproofing

of cable connection areas”  in the front page.

Install the camera stand on an even ceiling, wall, etc. ˎ

When installing the unit in an inverted position (on a ceiling, for

example)

Install the unit in a waterproof box or on a waterproof ceiling to prevent water ˎ

entering the unit along the cables. Alternatively, seal the hole which is made

for the connecting cables at the installing surface. ( -)

Cover all around the joint part of the installing surface and the camera stand ˎ

with sealant to prevent water ingress. (-)

When installing the unit in a vertical position (on a wall, for

example)

Make sure the TOP mark on the camera stand is at the top. ( ˎ- )

Cover all around the joint part of the installing surface and the camera stand ˎ

(except the water drain - ) with sealant to prevent water ingress.

Notes on assembly

Make sure the cable and the wire rope do not get caught between the base ˎ

stand and the mounting surface.

Before attaching the front cover to the camera unit, make sure the waterproof ˎ

rubber gasket is clean and fits in the groove properly.

When using white LEDs (SNC-VB642D only)

The white LEDs light up when the camera detects moving objects. Due to this,

the following limitations occur:

The accuracy of Motion detection (VMD*) may become lower depending on ˎ

the angle of the image or VMD settings.

In some scenes, the camera may detect an unintended object or may miss an ˎ

object.

The camera has built-in optical filters that switch automatically in conjunction ˎ

with the white LEDs. Automatic switching happens frequently depending on

where the camera is installed and it may affect the performance of the optical

filter. Perform proper VMD settings before using the camera.

* For details on VMD settings, see the User’s Guide.

Connection

Connecting to the Network 

Connect the LAN port of the camera to the router or hub on the network using a

commercially-available network cable (straight cable).

Connecting the Power Source 

SNC-VB642D

There are three ways to supply the power source to this camera, as follows.

12 V DC ˎ

24 V AC ˎ

Power supply equipment pursuant to IEEE802.3af/at (PoE/PoE+* system) ˎ

* PoE means Power over Ethernet.

Notes

Do not turn off the camera immediately after turning it on. Wait for at least five ˎ

minutes before turning off the camera.

Do not connect the power input cable if power is supplied by a PoE system. ˎ

When power is supplied by IEEE802.3af (PoE) equipment, do not set the ˎ

POWER switch to PoE+, AC, DC.

SNC-EB642R

Power supply equipment pursuant to IEEE802.3af (PoE* system)

* PoE means Power over Ethernet.

Note

Do not turn off the camera immediately after turning it on. Wait for at least five

minutes before turning off the camera.

Connecting to 12 V DC or 24 V AC source (SNC-VB642D)

Connect the power input cable of the camera to a 12 V DC or 24 V AC source.

Use a 12 V DC or 24 V AC source isolated from 100 to 240 V AC. Each usable ˎ

voltage range is as follows. (Assured range of the voltage the camera is

receiving (receiving-end voltage))

12 V DC: 10.8 V to 13.2 V

24 V AC: 19.2 V to 28.8 V

- In the USA, The product shall be powered by a UL Listed Class 2 Power

Supply Only.

- In Canada, The product shall be powered by a CSA certified Class 2 Power

Supply Only

Use UL cable (VW-1 style 10368) for these connections. ˎ

Recommended cable

When the receiving-end voltage of the camera is 12 V DC:

CABLE (AWG) #14 #16 #18

Max. length (m (feet)) 24 (78.7) 15 (49.2) 9 (29.5)

When the receiving-end voltage of the camera is 24 V AC:

CABLE (AWG) #20 #22 #24

Max. length (m (feet)) 100 (328.1) 63 (206.7) 39 (128)

Back hole

Sun shield nut

Sun shield

Sun shield nut

Sun shield

3,4,5,6,7

Base screw

Arm screw

ZOOM/

FOCUS

switch

Wrench (supplied)

For fixing the base

screws/arm screw

For fixing the

front cover screw

1,2

TOP mark

Rubber

gasket

Boss (four positions)

Sun shield nut

Sun shield

Sun shield nut

Sun shield

Correct

The waterproof rubber

gasket fits in the groove

properly.

After installing the front cover,

the gap between the front cover

and the camera unit is even.

Front coverCamera unit

Wrong



Router or hub Power input

cable

Ceiling

Commercially-

available

network cable

SNC-VB642D only

LAN cable

Unit: mm (inches)

85 (3 3/ )8

93 (3 3/ )4

83 (3 3/ )8

93 (3 3/ )4

Connecting to the power supply equipment pursuant

to IEEE802.3af/at

SNC-EB642R supports only power supply equipment that complies with

IEEE802.3af.

The power supply equipment pursuant to IEEE802.3af/at supplies the power

through a commercially available network cable. For details, refer to the

Instruction Manual of the equipment.

Note

If you connect the camera to power supply equipment pursuant to IEEE802.3at,

the equipment may limit the power supply and the camera may stop operating.

For details, refer to the instruction manual of the power supply equipment.

Connecting the I/O Cable (SNC-VB642D)

Connect the wires of the I/O cable as follows:

Wiring diagram for sensor input

Mechanical switch/open collector output device

Camera inside

3.3 V

2.2 K

Sensor input +

GND

Mechanical switch

Open collector

output device

Outside

GNDGND

10 K

(GND)

Sensor input −

Wiring diagram for alarm output

Camera inside

Alarm Output +

Magnet relay –

24 V AC

24 V DC,

1 A or less

Alarm Output –

Outside

5 V

Circuit example

GND

Specifications

Compression

Video compression format JPEG/H.264

Audio compression format G.711/G.726/AAC

Maximum frame rate 60 fps

Camera

IR LED 20 pcs

White LED (SNC-VB642D only) 4 pcs

IR working distance SNC-VB642D: 100 m (30 IRE)

SNC-EB642R: 60 m (30 IRE)

White LED working distance

(SNC-VB642D only)

11 m (30 IRE)

Signal system NTSC color system/PAL color system

(switchable)

Image device 1/2.8type CMOS (Exmor R)

Effective number of pixels: Approx. 2,130,000

Synchronization Internal synchronization

Horizontal resolution 700 TV lines (monitor display ratio 4:3)

Video S/N More than 50 dB (Auto gain control maximum

rate 0 dB)

Minimum illumination View-DR Off/VE* Off/Auto gain maximum rate

MAX/30 IRE (IP)/30 fps

F1.2/Color: 0.006 lx, Black & White: 0.005 lx

* VE stands for Visibility Enhancer.

Lens

Focal length 3.0 mm to 9.0 mm

Maximum relative aperture F1.2 to F2.1

View angle 1920 × 1080 (aspect ratio 16:9)

Vertical: 56.9° to 20.1°

Horizontal: 105.3° to 35.6°

Minimum object distance 300 mm

Interface

LAN port (PoE/PoE+) 10BASE-T/100BASE-TX, auto negotiation (RJ-45)

I/O port (SNC-VB642D only) Sensor input: × 2, make contact, break contact

Alarm output: × 2 (maximum 24 V AC/DC, 1A)

(mechanical relay outputs electrically isolated

from the camera)

SD memory card slot

Video output VIDEO OUT: BNC, 1.0 Vp-p, 75 ohms,

unbalanced, sync negative

Microphone input* Minijack (monaural)

Plug-in-power supported (rated voltage: 2.5 V DC)

Recommended load impedance: 2.2 kΩ

Line input* Minijack (monaural)

* The microphone input and the line input are switchable with operating menu.

Line output Minijack (monaural), Maximum output level:

1 Vrms

Others

Power supply SNC-VB642D

12 V DC ± 10%

24 V AC ± 20%, 50 Hz/60 Hz

IEEE802.3af/at compliant (PoE/PoE+ system)

SNC-EB642R

IEEE802.3af compliant (PoE system)

Power consumption SNC-VB642D

Max. 21 W (AC 24 V/DC 12 V is selected)

Max. 17 W (IEEE802.3at (PoE+) is selected)

Max. 12.5 W (IEEE802.3af (PoE) is selected)

SNC-EB642R

Max. 12.5 W (IEEE802.3af (PoE) is selected)

Operating temperature SNC-VB642D

Start temperature:

–30°C to +60°C (–22°F to +140°F) (LED OFF;

PoE+, AC 24 V, DC 12 V is selected)

–30°C to +50°C (–22°F to +122°F) (LED ON;

PoE+, AC 24 V, DC 12 V is selected)

0°C to +60°C (+32°F to +140°F) (LED OFF, PoE

is selected)

0°C to +50°C (+32°F to +122°F) (LED ON, PoE is

selected)

Working temperature:

–40°C to +60°C (–40°F to +140°F) (LED OFF;

PoE+, AC 24 V, DC 12 V is selected)

–40°C to +50°C (–40°F to +122°F) (LED ON;

PoE+, AC 24 V, DC 12 V is selected)

–10°C to +60°C (+14°F to +140°F) (LED OFF,

PoE is selected)

–10°C to +50°C (+14°F to +122°F) (LED ON, PoE

is selected)

SNC-EB642R

Start temperature:

–20°C to +50°C (–4°F to +122°F)

Working temperature:

–30°C to +50°C (–22°F to +122°F)

Storage temperature –20°C to +60°C (–4°F to +140°F)

Operating humidity 20% to 90% (no condensation)

Storage humidity 20% to 80% (no condensation)

Dimensions (diameter/height) 

93 mm × 93 mm × 180.9 mm (3 3/4 inches ×

3 3/4 inches × 7 1/8 inches) , not including the

projecting parts

Mass SNC-VB642D: Approx. 1,620 g (3 lb 9.1 oz)

SNC-EB642R: Approx. 1,610 g (3 lb 8.8 oz)

Supplied accessories Template (1), Wrench (1), Safety Regulation

(1 set), Waterproof tape (1)

Design and specifications are subject to change without notice.

Detached Uneven gap

Uneven gap Foreign matter stuck

Produktspezifikationen

Marke:	Sony
Kategorie:	Sicherheitskamera
Modell:	SNC-VB642D
Schutzfunktion:	Vandalismussicher
Unterstützte Audioformate:	AAC
Breite:	93 mm
Tiefe:	93 mm
Gewicht:	1620 g
Produktfarbe:	Black, White
Internationale Schutzart (IP-Code):	IP66
Übertragungstechnik:	Kabelgebunden
Höhe:	180.9 mm
Energiequelle:	PoE
Befestigungstyp:	Zimmerdecke
AC Eingangsspannung:	24 V
Betriebstemperatur:	-40 - 60 °C
Relative Luftfeuchtigkeit in Betrieb:	20 - 90 %
Netzstandard:	IEEE 802.1x
Unterstützte Netzwerkprotokolle:	IPv4, TCP, UDP, ARP, ICMP, IGMP, HTTP, DHCP, DNS, NTP, RTP/RTCP, RTSP over TCP, SMTP over HTTP, IPv6, HTTPS, FTP (client), SNMP (v1, v2c, v3), SSL
Quality of Service (QoS) Support:	Ja
Automatische Gewinnkontrolle:	Ja
Sprachcodec:	G.711, G.726
Zertifizierung:	UL2044, IEC60950-1, VCCI, FCC, IC, EN55032, EN55024, EN50130-4, AS/NZS CISPR32, KC, EMC-TR
Power over Ethernet (PoE):	Ja
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Typ:	IP-Sicherheitskamera
Stromverbrauch (max.):	21 W
Betriebsanleitung:	Ja
Zahl der Benutzer:	20 Benutzer
Temperaturbereich bei Lagerung:	-20 - 60 °C
Luftfeuchtigkeit bei Lagerung:	20 - 80 %
Unterstützt Windows-Betriebssysteme:	Windows 10, Windows 7, Windows 8.1
Unterstützte Sprachen:	ARA, CHI (SIMPL), CHI (TR), DEU, ENG, ESP, FRE, HIN, ITA, JPN, KOR, POL, POR, RUS, THA, TUR
Analoges Signalformatsystem:	NTSC, PAL
Unterstützte Grafik-Auflösungen:	352 x 288,640 x 360,640 x 480 (VGA),704 x 576,720 x 480,720 x 576,1024 x 576 (WSVGA),1280 x 720 (HD 720),1920 x 1080 (HD 1080)
Rauschverhältnis (SNR):	50 dB
Frequenzbereich:	16000 - 48000 Hz
Naheinstellgrenze:	0.3 m
Mikrofon-Eingang:	Ja
Full-HD:	Ja
Zoom-Fähigkeit:	Ja
Digitaler Zoom:	4 x
Geräuschunterdrückung:	Ja
Größe des Bildsensors:	1/2.8 "
PTZ Kontrolle:	Ja
Formfaktor:	Bullet
Kompatible Speicherkarten:	SD
Max. Speicherkartengröße:	256 GB
Webbrowser:	Ja
Integrierter Kartenleser:	Ja
Videokompressionsformate:	H.264
Maximale Auflösung:	1920 x 1080 Pixel
Ethernet Schnittstellen Typ:	Schnelles Ethernet
Verkabelungstechnologie:	10/100Base-T(X)
Brennweitenbereich:	3 - 9 mm
Bis zu 30 Frames pro Sekunde:	60 fps
Anzahl der Kameras:	1
Tag/ Nachtmodus:	Ja
Mindestbeleuchtung:	0.006 Lux
Nachtsichtdistanz:	100 m
LED Typ:	IR
Sensor-Typ:	CMOS
Bildstabilisator:	Ja
Optischer Zoom:	3 x
Objektivanschluss:	CS-Halterung
Weißabgleich:	ATW, Fluorescent, Indoor, Manual, Mercury lamp, One push, Outdoor, Sodium lamp
Nachtsicht:	Ja
Kamera Verschlusszeit:	1 - 1/10000 s
Vollbildverfahren:	Ja
Maximale Blendenzahl:	2.1
Datenschutz-Maskierung:	Ja
Bitratenkontrolle:	Constant Bit Rate (CBR), Variable Bit Rate (VBR)
Übertragungsgeschwindigkeit:	64 Kbps - 32 Mbps
Intelligent Video Surveillance-(IVS)-System-Eigenschaften:	Abandoned object, Face detection, Missing object
Infrarot-Wellenlänge:	850 nm
Stromverbrauch (Power over Ethernet (PoE)):	17 W
Alarmeingabe/-ausgabe:	Ja
Betrachtungswinkel (horizontal):	105.3 °
Betrachtungswinkel (vertikal):	56.9 °
Minimale Blendenzahl:	1.2
Objektivtyp:	Varifokal
Minimum Prozessor:	Intel Corei7 2.8 GHz
BNC Ausgänge:	1
Anzahl der Sprachen:	17
Streaming-Verfahren:	Multicasting
Iris:	Ja
Eingebaute Heizung:	Ja
Ethernet/LAN:	Ja
Unterstützte Positionierung:	Draußen
Wetterfestigkeit:	Ja