Sony SNC-VB640 Bedienungsanleitung

Sony Sicherheitskamera SNC-VB640

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sony SNC-VB640 (4 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

About the Manuals

Safety Regulations (included)

The Safety Regulations describes notes for the secure usage of camera. Be sure

to read it.

Installation Manual (this document)

Describes the names and functions of parts and controls of the Network Camera,

gives connection examples and explains how to set up the camera. Be sure to

read the Installation Manual before operating.

The illustration of SNC-VB640 is used for example purpose.

Electronic Instruction Manual (Web)

How to control the camera via a web browser ˎ

How to setup the camera ˎ

Operate the camera referring to the guide above after having installed and

connected the camera properly based on the Installation Manual.

Assigning the IP address

1 Download the installer for “SNC toolbox” to a folder from the download

site.

2 Install the SNC toolbox.

Unzip the ZIP file of the downloaded installer.

Double-click “SncToolbox_Setup.exe.” For details on installing and use refer to

the Application Guide.

3 Assign an IP address.

Assign an IP address using the installed SNC toolbox. For details, see “Using

SNC toolbox” – “Assign an IP address” in the Application Guide.

Tip

SNC toolbox stands for Sony Network Camera toolbox.

Location and Function of Part

Front 

 Lens

A vari-focal lens is mounted as standard equipment.

 Focus ring

Turn this ring toward N (near) to focus on a closer object. Turn it toward ∞

(infinite) to focus on a farther object.

 Zoom ring

Turn this ring toward T for telephoto, or toward W for wide-angle.

 Tripod screw hole

Use this screw hole when attaching the camera to a

tripod (screw: 1/4”, 20 UNC). You can attach a tripod to

either the top or bottom of the camera.

Caution

Use the mounting screw whose length is 4.5 mm – 7 mm only. Use of other

screws may cause improper mounting and damage parts inside the camera.

 Rating Label

This label shows the name of device and its electric rating.

 Lens connector (4-pin socket)

Supplies power and control signals to an auto-iris lens.

Rear 

 Fall-prevention wire rope mounting screw hole

When installing the camera to the ceiling or the wall, secure the supplied wire

rope to this hole using the supplied screw.

 VIDEO OUT (video output) connector

Connect the commercially-available BNC cable.

 NETWORK indicator

The indicator lights up or flashes when the camera is connected to the network.

The indicator is off when the camera is not connected to the network.

 (microphone input) jack (minijack, monaural)

Connect a commercially available microphone.

This jack supports plug-in-power microphones (rated voltage: 2.5 V DC).

 POWER indicator (Green)

When the power is supplied to the camera, the camera starts checking the

system. If the system is normal, this indicator lights up.

 Reset switch

To reset the camera to the factory default settings, turn on the power to the

camera while holding down this switch with a pointed object.

U1/4”, 20 UNC

= 4.5 mm - 7 mm

(ISO standard) (with the

screws fastened)

 (ground) terminal

This is the ground terminal for the chassis. Be sure to connect to the ground

terminal.

 I/O (Input/Output) port (SNC-VB640 only)

This port provides two sensor inputs and two alarm outputs.

The signal pin assignment is as follows.

PinNo. Signal

1 Sensor input 1+

2 Sensor input 2+

3 Sensor input– (GND)

4 Alarm output 1+

5 Alarm output 1–

6 Alarm output 2+

7 Alarm output 2–

For details on each function and required settings, see the User’s Guide.

Connect the wires of the I/O cable as follows:

Wiring diagram for sensor input

Mechanical switch/open collector output device

Camera inside Outside

GND

Mechanical

switch

Open collector output

device

3.3 V

2.2 kΩ

Sensor input −

(GND)

10 kΩ

GND GND

10 kΩ

Sensor input +

4-696-252- (1)11

Network Camera

SNC-VB640/EB640

Installation Manual

Before operating the unit, please read this manual thoroughly and

retain it for future reference.

Wiring diagram for alarm output

Camera inside Outside

5 V

Alarm Output +

GND

Magnet relay

24 V AC

24 V DC

1 A or less

Circuit example

Alarm Output −

 DC 12 V/AC 24 V (power input) terminal (SNC-VB640 only)

Connect to a 12 V DC or 24 V AC power supply system. ( -1)

 (line output) jack (minijack, monaural)

Connect a commercially available speaker system with a built-in amplifier.

 LAN network port (RJ-45)

Connect a network cable (UTP, category 5) to this port to communicate with a

network or PoE* system.

For details on connection, see the Instruction Manual of the power supply

equipment.

(*PoE stands for Power over Ethernet. It is pursuant to IEEE802.3af.)

 Easy Focus button

Adjust the focus approximately by the focus ring, then press this button to

automatically adjust the focus.

To load the default setting, press and hold this button for more than 4 seconds.

 NTSC/PAL switch

Switching the video output.

After setting the switch, reboot the camera unit.

 SD card slot cover

To remove the SD card slot cover, pull the cover forward, and insert the memory

card.

When closing the cover, be sure to close it completely by pushing on the hook

on the end until it locks in place.

 SD card slot

This slot is used for optional SD memory cards.

Image data in the camera can be recorded to a memory card by inserting it into

the slot.

When inserting, point the contact area at the rating label side (referring to the

illustration), and be sure to insert it completely. ( -2)

This unit is only compatible with SD and SDHC memory cards.

Note

For inquiries regarding verified SD memory cards, contact your authorized Sony

dealer.

A B

Installation

Caution

To prevent the camera from falling, make sure to attach the supplied wire

rope.

Suitable lens 

The lens must be a CS-mount type and the protrusion behind the mounting

surface must be 5.5 mm ( inch) or less./

Caution

When you install it into a wall or a ceiling, check that the wall or the ceiling ˎ

is strong enough to hold the weight of the camera including the mounting

bracket, and install it without fail. If not, the camera falls down and causes

a serious injury.

Also, check if the mounting is not loosened at least once a year. Make the

checking interval short according to use condition.

Performance will depend on the installation environment and the lens ˎ

itself. For details, contact your authorized Sony dealer.

Attaching the wire rope 

When you install the camera on a ceiling or a high position, be sure to attach the

supplied wire rope to prevent the camera from falling.

Attach the wire rope to the screw hole on the rear of the camera, as in the

illustration.

Note

Take care not to short-circuit the power terminal or the cable with the wire rope

when you attach it.

1 Secure the wire rope to the junction box on the ceiling.

Use a commercially-available screw to match the screw hole of your junction

box.

2 Secure the wire rope to the wire rope mounting screw hole on the rear of

the camera using the supplied screw.

Caution

Use the supplied screws for installation. If not, the wire rope may not function

properly.

Adjusting the Camera Coverage and Focus 

1 Loosen the zoom ring locking screw to adjust the camera shooting

coverage.

2 Tighten the locking screw to fix the zoom.

3 Loosen the focus ring locking screw to adjust the focus.

4 Tighten the locking screw to fix the focus ring.

5 Press the Easy Focus button on the rear to automatically adjust the

focus.

Note

You may not achieve satisfactory focus with the Easy Focus button due to the

shooting environment.

In this case, press and hold the Easy Focus button for more than 4 seconds to

return to the default position. Then, adjust the focus following step 3 and 4.

Connection

Connecting to the Network

Connect the LAN connector of the camera to a PoE* supported device (such as a

hub) using the network cable (straight cable).

The electrical power is supplied through the network cable. For details, refer to

the instruction manuals of the PoE supported devices.

(* PoE: The acronym for Power over Ethernet. IEEE802.3af standard compliant

devices.)

For SNC-VB640, it is possible to connect the LAN port of the camera to a router or

hub in the network using a commercially-available network cable.

Connecting the Power Source

The camera can be powered in the following ways.

12 V DC or 24 V AC (Either voltage supported by SNC-VB640 only.) ˎ

Power supply equipment pursuant to IEEE802.3af (PoE* system) ˎ

* PoE stands for Power over Ethernet.

Notes

Do not turn off the camera immediately after turning it on. Wait for at least five ˎ

minutes before turning off the camera.

Do not connect the power input cable if power is supplied by a PoE system. ˎ

Connecting to the power supply equipment pursuant to IEEE802.3af

The power supply equipment pursuant to IEEE802.3af supplies the power

through the network cable. For details, refer to the Instruction Manual of the

equipment.

Connecting to 12 V DC or 24 V AC source

Connect the power input cable of the camera to a 12 V DC or 24 V AC source.

Use a 12 V DC or 24 V AC source isolated from 100 to 240 V AC. The acceptable ˎ

voltage ranges for each are as follows.

12 V DC: 10.8 V to 13.2 V

24 V AC: 19.2 V to 28.8 V

- In the USA, The product shall be powered by a UL Listed Class 2 Power

Supply Only.

- In Canada, The product shall be powered by a CSA certified Class 2 Power

Supply Only.

Use UL cable (VW-1 style 10368) for these connections. ˎ

Recommended cable

12 V DC:

CABLE (AWG) #24 #22 #20

Max. length (m (feet)) 8 (26.2) 14 (45.9) 20 (65.5)

24 V AC:

CABLE (AWG) #24 #22 #20

Max. length (m (feet)) 11 (36.1) 19 (62.3) 28 (91.9)

Specifications

Compression

Video compression format JPEG/H.264

Audio compression format G.711/G.726/AAC

Maximum frame rate 60 fps

Camera

Signal system NTSC color system/PAL color system

(switchable)

Image device 1/2.8type CMOS (Exmor R)

Effective number of pixels: approx. 2,130,000

Synchronization Internal synchronization

Horizontal resolution 700 TV lines (monitor display ratio 4:3)

Video S/N More than 50 dB (Auto gain control maximum

rate 0 dB)

Minimum illumination View-DR Off/VE* Off/Auto gain control

maximum rate

MAX/30 IRE (IP)/30 fps

F1.2/Color: 0.006 lx, Black & White: 0.005 lx

* VE stands for Visibility Enhancer.

Lens

Focal length 2.8 mm to 8 mm

Maximum relative aperture F1.2 to F1.95

View angle* 1920 × 1080 (aspect ratio 16:9)

Vertical: 60.6° to 22.5°, Horizontal: 114.2° to

40.0°

* The view angle will change, depending on the setting of the aspect ratio

resolution.

Minimum object distance 300 mm

Interface

LAN (PoE) 10BASE-T/100BASE-TX, auto negotiation (RJ-45)

I/O port (SNC-VB640 only) Sensor input: × 2, make contact, break contact

Alarm output: × 2, 24 V AC/DC, 1 A max.

(mechanical relay outputs electrically isolated

from the camera)

SD memory card slot

Video output VIDEO OUT: BNC, 1.0 Vp-p, 75 ohms,

unbalanced, sync negative

Microphone input* Minijack (monaural)

Plug-in-power supported (rated voltage: 2.5 V

DC)

Recommended load impedance: 2.2 k

Line input* Minijack (monaural)

* The microphone input and the line input are switchable with operating menu.

Line output Minijack (monaural), Maximum output level:

1 Vrms

CS-mount lens

5.5 (/) or less

Unit: mm (inch)

Screw (supplied)

Wire rope (supplied)

Commercially-

available screws

E F

Front

72 (2 /)

62 (2 /)

63 (2 /)

Side 145 (5 /)

44 (1 /)*

55 (2 /)*

54.1 (2 /)

150.5 (6)

Unit: mm (inches)

Others

Power supply SNC-VB640:

12 V DC ± 10%

24 V AC ± 20%, 50 Hz/60 Hz

IEEE802.3af compliant (PoE system)

SNC-EB640:

IEEE802.3af compliant (PoE system)

Power consumption 6.0 W max.

Operating temperature Start temperature: 0°C to 50°C (32°F to 122°F)

Working temperature: –10°C to +50°C

(14°F to 122°F)

Storage temperature –20°C to +60°C (–4°F to +140°F)

Operating humidity 20% to 80% (no condensation)

Storage humidity 20% to 80% (no condensation)

Dimensions (w/h/d) 72 mm × 63 mm × 145 mm (2 7/ inches × 8

2 1/ inches × 5 23/ inches) not including the 4

projecting parts and lens

Mass SNC-VB640:

Approx. 565 g (1 lb 3.9 oz) (with lens)

SNC-EB640:

Approx. 550 g (1 lb 3.4 oz) (with lens)

Supplied accessories Wire rope (1)

Screw M4 (1)

Safety Regulations (1)

DC 12 V/AC 24 V connector (1) (SNC-VB640

only)

Design and specifications are subject to change without notice.

* Tripod screw hole position

Produktspezifikationen

Marke:	Sony
Kategorie:	Sicherheitskamera
Modell:	SNC-VB640
Unterstützte Audioformate:	AAC
Breite:	72 mm
Tiefe:	145 mm
Gewicht:	565 g
Produktfarbe:	Black, White
Übertragungstechnik:	Kabelgebunden
Höhe:	63 mm
Energiequelle:	PoE
AC Eingangsspannung:	24 V
Betriebstemperatur:	-10 - 50 °C
Relative Luftfeuchtigkeit in Betrieb:	20 - 80 %
Netzstandard:	IEEE 802.1x, IEEE 802.3af
Unterstützte Netzwerkprotokolle:	IPv4, TCP, UDP, ARP, ICMP, IGMP, HTTP, DHCP, DNS, NTP, RTP/RTCP, RTSP over TCP, SMTP over HTTP, IPv6, HTTPS, FTP (client), SNMP (v1, v2c, v3), SSL
Quality of Service (QoS) Support:	Ja
Automatische Gewinnkontrolle:	Ja
Sprachcodec:	G.711, G.726
Zertifizierung:	UL2044, IEC60950-1, VCCI, FCC, IC, EN55032, EN55024, EN50130-4, AS/NZS CISPR32, KC, EMC-TR
Power over Ethernet (PoE):	Ja
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Typ:	IP-Sicherheitskamera
Stromverbrauch (max.):	6 W
Betriebsanleitung:	Ja
Zahl der Benutzer:	20 Benutzer
Temperaturbereich bei Lagerung:	-20 - 60 °C
Luftfeuchtigkeit bei Lagerung:	20 - 80 %
Unterstützt Windows-Betriebssysteme:	Windows 10, Windows 7, Windows 8.1
Unterstützte Sprachen:	ARA, CHI (SIMPL), CHI (TR), DEU, ENG, ESP, FRE, HIN, ITA, JPN, KOR, POR, RUS, THA
Analoges Signalformatsystem:	NTSC, PAL
Unterstützte Video-Modi:	1080p
Unterstützte Grafik-Auflösungen:	352 x 288,640 x 360,640 x 480 (VGA),704 x 576,720 x 480,720 x 576,1024 x 576 (WSVGA),1280 x 720 (HD 720),1920 x 1080 (HD 1080)
Rauschverhältnis (SNR):	50 dB
Frequenzbereich:	16000 - 48000 Hz
Naheinstellgrenze:	0.3 m
Mikrofon-Eingang:	Ja
Full-HD:	Ja
Zoom-Fähigkeit:	Ja
Digitaler Zoom:	4 x
Geräuschunterdrückung:	Ja
Größe des Bildsensors:	1/2.8 "
PTZ Kontrolle:	Ja
Formfaktor:	Box
Kompatible Speicherkarten:	SD
Max. Speicherkartengröße:	256 GB
Webbrowser:	Ja
Integrierter Kartenleser:	Ja
Videokompressionsformate:	H.264
Maximale Auflösung:	1920 x 1080 Pixel
Ethernet Schnittstellen Typ:	Schnelles Ethernet
Verkabelungstechnologie:	10/100Base-T(X)
Brennweitenbereich:	2.8 - 8 mm
Bis zu 30 Frames pro Sekunde:	60 fps
Megapixel insgesamt:	2.13 MP
Anzahl der Kameras:	1
Tag/ Nachtmodus:	Ja
Mindestbeleuchtung:	0.005 Lux
Sensor-Typ:	CMOS
Bildstabilisator:	Ja
Optischer Zoom:	2.9 x
Objektivanschluss:	CS-Halterung
Weißabgleich:	ATW, Fluorescent, Manual, Mercury lamp, One push, Sodium lamp
Schrauben enthalten:	Ja
Nachtsicht:	Nein
Kamera Verschlusszeit:	1 - 1/10000 s
Maximale Blendenzahl:	1.95
Datenschutz-Maskierung:	Ja
Bitratenkontrolle:	Constant Bit Rate (CBR), Variable Bit Rate (VBR)
Übertragungsgeschwindigkeit:	64 Kbps - 32 Mbps
Video-Bewegungsmelder:	Ja
Intelligent Video Surveillance-(IVS)-System-Eigenschaften:	Abandoned object, Face detection, Missing object
Alarmeingabe/-ausgabe:	Ja
Betrachtungswinkel (horizontal):	114.2 °
Betrachtungswinkel (vertikal):	60.6 °
Minimale Blendenzahl:	1.2
Objektivtyp:	Varifokal
Minimum Prozessor:	Intel Corei7 2.8 GHz
BNC Ausgänge:	1
Anzahl der Sprachen:	15
Streaming-Verfahren:	Multicasting
Iris:	Ja
Ethernet/LAN:	Ja
Unterstützte Positionierung:	Drinnen