Sonos Sonance Bedienungsanleitung

Sonos Lautsprecher Sonance

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sonos Sonance (6 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/6

S O N O S I N - C E I L I N G

BY S O N A N C E

INSTALLATION MAN UAL

Introduction

Thank you for purchasing SONOS IN-CEILING by SONANCE

Speakers. When properly installed your new speakers will give

you years of entertainment pleasure.

Box Contents

(2) SONOS In-Ceiling Speakers

(2) Paintable Grilles

(2) Mounting Cut-out Templates

Speaker Placement

Stereo Speaker Placement (2-Channel System)

• Place the left and right speakers anywhere from 6 - 10 feet

(1.8m – 3m) apart, with the main listening position as close to

midway between the speakers as possible.

• In most cases pivoting the woofer and/or midrange/tweeter

assembly of each speaker directly towards the main listening

position will help maximize the stereo soundstage.

Use the left and right speaker placement in Figures 2 and 3, on

the left side of image, as a guide.

NOTE: CONSULT LOCAL BUILDING CODES BEFORE RUNNING SPEAKER WIRES THROUGH CEILINGS.

Figure 1: Distributed Audio Speaker Spacing

Coverage Area Coverage Area

Speaker

Spacing

Distributed Audio System Speaker Spacing

Standing Listener Seated Listener

8 Foot Ceiling 5’7” (1.7m) apart 9’5” (2.9m) apart

10 Foot Ceiling 9’7” (3m) apart 13’5” (4.1m) apart

12 Foot Ceiling 13’7” (4.2m) apart 17’5” (5.3m) apart

14 Foot Ceiling 17’7” (5.4m) apart 21’5” (6.6m) apart

Figure 2: 5.1 Channel Home Theater Speaker Placement

Left, Center

& Right

Speakers

Left & Right

Surround

Speakers

6’-10’

(1.8-3m)

apart

2’-6’

(0.6-1.8m)

apart

Home Theater Speaker Placement

Surround Speakers — 5.1-Channel System

• Locate the left and right surround speakers 2 – 6 feet (0.6

– 1.8m) behind the listening position. The speakers should be 6

– 10 feet (1.8 – 3m) apart (see Figure 2).

Surround Speakers — 7.1-Channel System

• Left & Right Surround Speakers: Place the left and right

surround speakers directly to the sides of the listening position,

6 –10 feet (1.8 – 3m) apart (see Figure 3).

Surround Back Speakers

• Place the surround back speakers 2 – 6 feet (0.6 – 1.8m) behind

the listening position. The surround back speakers should be

closer together than the left and right surround speakers, 3 – 6

feet (0.9 – 1.8m) apart.

Figure 3: 7.1 Channel Home Theater Speaker Placement

Left, Center

& Right

Speakers

Left & Right

Surround

Speakers

3’-6’

(0.9-1.8m)

apart

2’-6’

(0.6-1.8m)

apart

Before Installation

1. Determine the location for the speaker (see Speaker

Placement above).

2. Perform an obstruction survey using a stud ﬁnder to be certain

that there are no studs, conduit, pipes,heating,ducts, pocket

doors or air returns in the ceiling cavity that will interfere with

the speaker. If you are unsure about obstructions, drill a small

hole in the center of the outline and insert a coat hanger wire

into the hole to feel around for possible obstructions.

3. Cut the mounting hole using a keyhole or drywall saw, and run

the speaker wires from the mounting hole to the ampliﬁer

location.

Installation

SONOS In-Ceiling by Sonance features integral Roto-Lock®

mounting system for quick mounting directly into

existing ceilings.

1. Strip 1/4 – 1/2” (6 – 12mm) of insulation from each speaker

lead. Twist the strands or tin the exposed wire with solder to

ensure that there are no stray strands.

NOTE: STRAY STRANDS THAT TOUCH EACH OTHER CAN CAUSE A SHORT-CIRCUIT THAT CAN DAMAGE

THE AMPLIFIER.

2. The speaker’s terminals are spring-loaded. Push the top of

each terminal down to open the connector and insert the

exposed wires into the holes in the spring terminals.

The speaker’s positive spring terminal is labeled with a red dot;

the negative spring terminal is labeled with a black dot. Double

check that you connected ampliﬁer “+” to speaker “+” and

ampliﬁer “–” to speaker “–”.

3. Make sure all the Roto-Lock toggle feet are retracted so that

they are tucked within the mounting hole’s border. Insert the

speaker into the hole in the ceiling (see Figure 5). The Roto-

Lock system can accommodate a ceiling material thickness of

1-1/4” (32mm) with the toggle foot cap removed the system can

accommodate a ceiling material thickness of 1-7/8” (48mm).

4. When installing into double drywall or other thicker ceiling

materials, you may need to remove part of the two-piece

toggle feet. Use a small screwdriver to gently release the two

locking levers (see Figure 4).

5. Tighten the screws on the front of the speaker bae. The Roto-

Lock toggle feet will automatically rotate into position and

begin clamping the speaker (see Figure 6). When you notice

resistance on the screws the speaker has been

clamped successfully.

6. The micro-trim grille is held in place by several small, powerful

magnets on the speaker frame. Place the grille against the

speaker and the magnets will hold it ﬁrmly in place. When

properly installed, the grille trim should make contact with the

wall all the way around the speaker.

Figure 4: Removing the Caps from the Roto-Lock Toggle Feet

Remove

Cap

Locking Levers

Figure 5: Inserting the Speaker into the Mounting Hole

Roto-Lock Clamps

(retracted)

Figure 6: Tightening the Roto-Lock Screws

Roto-Lock Screws

IMPORTANT: ALWAYS USE LOW TORQUE SETTINGS; NEVER OVER-TIGHTEN.

NOTE: ADJUST THE TENSION OF THE ROTO-LOCK CLAMPS SO THAT THE SPEAKER FRAME IS FLAT. THIS

WILL HELP ENSURE THAT THE GRILLE CONTACTS THE CEILING ALL THE WAY AROUND THE SPEAKER

FOR A PROPER FIT.

Speaker Adjustments

Pivoting Woofer and Midrange/Tweeter

SONOS In-Ceiling speakers have a pivoting woofer and a

pivoting midrange/tweeter assembly. If you’re using the speakers

in stereo or as the front left/center/right speakers in a home

theater, pivot the drivers directly towards the listening area.

If you’re using the speakers as surround channel speakers in a

home theater, pivot the drivers towards a wall or window, away

from the listeners.

To pivot the drivers apply light pressure to the ring around the

outside edge of the woofer, midrange and tweeter cone, as

shown in Figure 7. Take care not to touch or apply pressure to the

cone itself.

Figure 7: Pivoting Tweeter Left, Pivoting Woofer Right

Unlocking Sonos Audio

Enhancements

Sonos In-Ceiling by Sonance speakers include exclusive audio

enhancements when used with a Sonos Amp. Use the free Sonos

app to unlock them.

Produktspezifikationen

Marke:	Sonos
Kategorie:	Lautsprecher
Modell:	Sonance
Breite:	235.4 mm
Tiefe:	235.4 mm
Gewicht:	4550 g
Produktfarbe:	Schwarz, Silber
Übertragungstechnik:	Kabellos
Impedanz:	8 Ohm
Höhe:	123 mm
RMS-Leistung:	130 W
Menge pro Packung:	2 Stück(e)
Verpackungsart:	Box
Audio Kanäle:	2.0 Kanäle
Frequenzbereich:	44 - 20000 Hz
Woofer:	Ja
Tieftönerdurchmesser (imperial):	6.5 Zoll
Hochtöner:	Ja
Hochtönerdurchmesser (Imperial):	1 Zoll
Lautsprecherplatzierung:	in-Wand/in-Decke
Hochtönerdurchmesser:	25 mm
Empfindlichkeit:	89 dB
Lautsprechertyp:	2-Wege
Tieftönerdurchmesser:	165 mm