Sonos Outdoor by Sonance Bedienungsanleitung

Sonos Lautsprecher Outdoor by Sonance

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sonos Outdoor by Sonance (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
S O N O S O U T D O O R
BY S O N A N C E
INSTALLATION MAN UAL
Types of Wire
When installing SONOS OUTDOOR by SONANCE Speakers
careful consideration should be made when determining speaker
placement and wire gauge. Refer to the wiring chart (see figure
2) to determine which size wire to use over the given distance
between the SONOS Amplifier and the speakers.
W I R E G A U G E C H A R T
18 Gauge Up to 100 feet (30 meters)
Up to 150 feet (45 meters)
Up to 250 feet (80 meters)
WIRE GAUGE DISTANCE
16 Gauge
14 Gauge
Figure 2: Wire Gauge Chart
Connecting and Assembling
WARNING: TURN THE AMPLIFIER’S POWER OFF UNTIL YOU HAVE COMPLETED ALL OF THE
CONNECTIONS AND HAVE DETERMINED THAT THEY ARE CORRECT. (IF THE AMP’S AC PLUG IS
ACCESSIBLE WE RECOMMEND THAT YOU UNPLUG IT FROM THE WALL OUTLET TO AVOID ACCIDENTAL
TURN-ON AND POSSIBLE DAMAGE TO THE AMPLIFIER.)
1. In most cases you will be able to attach
the FastMount brackets directly to the
mounting surface. Run the speaker wires
from the amplifier to the speaker
locations and through the holes in the
brackets if used (see figure 3).
NOTE: TO INCREASE WATER RESISTANCE AND MAKE
INSTALLATION EASIER, THE SPEAKER WIRE TERMINALS ARE
LOCATED ON THE SPEAKERS’ FRONT PANEL. BE SURE TO LEAVE
ENOUGH WIRE AT THE SPEAKER LOCATION TO FEED THROUGH
THE TUNNEL IN THE SPEAKER ENCLOSURE AND CONNECT TO
THE TERMINALS ON THE FRONT.
Figure 3: Pass Wire
Through Hole and
Attach Bracket
2. Attach the FastMount brackets to the
mounting surface using hardware (not
included) that is appropriate for the type
of surface (see figure 3).
• If the installation requires that the
speaker be mounted in a corner,
attach the bracket with hardware (not
included) through the slots in the angled
corners (see figure 4).
3. If the installation requires that the
speaker be mounted on a pole you can
attach the FastMount brackets to the
pole using 2.5” U-bolts (not included)
(see figure 5).
4.Feed the speaker wires from the
bracket into the wire entry grommet
on the back of the speaker, through the
wire tunnel and out the opening on the
speaker’s front panel (see figure 6).
• The grommet forms a water- resistant
seal around the speaker wire.
• Make sure there is enough slack in the
wire to allow the speaker to pivot on
the bracket.
Figure 4:
Corner Mounting
Figure 5:
Attaching the
Bracket to a Pole
Figure 6: Wire
Entry Grommet
Product Description
Thank you for purchasing SONOS OUTDOOR by SONANCE
weather-resistant speakers.
When properly installed, these speakers will give you many years
of outdoor entertainment pleasure. To get the most out of your
new speakers, please read this manual thoroughly before you
begin installation.
The directions in this manual apply to the following models:
SONOS OUTDOOR by SONANCE
Box Contents
(2) Speakers
(2) Speaker Grilles
(2) FastMount® Brackets
(2) Wiring Terminal Covers
Speaker Placement
SONOS OUTDOOR by SONANCE speakers are highly weather-
resistant, and when mounted outdoors will perform exceptionally
well for years, even under adverse weather conditions.
The FastMount bracket system makes it easy to mount the
speakers in a variety of positions and locations: (see figure 1).
Under an eave
Flush against a wall
In a corner
Pole mount
(U-Bolts not included)
The best performance is obtained by placing the speakers
directed toward the listening area.
If you are mounting the speakers above or below ear level,
pivot them up or down to direct the sound towards
the listeners.
You can orient the speakers either horizontally or vertically
without aecting the sound quality. For vertical orientation,
please ensure that the tweeter is in the upright position with
the SONOS logo toward the bottom as shown in the “pole
mount” illustration in figure 1.
Figure 1: Speaker Placement
2
3
5. Slide the speaker onto the bracket and firmly snap into place
at the top and bottom of speaker. Pull enough wire through the
front of the speaker to allow connection to the terminals (see
figure 7).
6. Connect the speaker wires to the speaker’s terminals:
• Strip about .5” of insulation from each conductor and twist the
strands together or tin them with solder.
• Press-down on the tops of the connectors to open them.
• Insert the wires into the connector holes(see figure 8).
• Release the connectors.
The binding post connectors can accept wire up to 14 gauge.
Double-check that you connected all of the wires properly
(amplifier ‘+’ to speaker ‘+’; amplifier ‘–’ to speaker ‘–’) at
all connections.
Figure 7: Attach Speakers to Brackets
Figure 8: Connection Terminals
7. Fit the wiring connector cover into the recess in the speaker’s
front panel. The cover should fit tightly, but can be removed if
the speaker needs to be disconnected (see figure 9).
8. Fit the grille onto the speaker by aligning the edges of the grille
with the groove of the speaker face perimeter and pressing
firmly until it is snugly in place (seegure 10). Start by inserting
and pressing along the long edge, then insert one of the short
edges. Continue with the other long edge, and finally the other
short edge.
Figure 9: Attach the
Connector Cover
Figure 10: Attach the
Grille
UNLOCK (towards rear of speaker)
LOCK (towards front of speaker)
Figure 11: Lock and Unlock Slide Locks to Pivot Speaker
NOTE: ALL SONOS OUTDOOR BY SONANCE SPEAKERS ARE COMPATIBLE WITH OMNIMOUNT STAINLESS
STEEL 15.0 C AND 15.0 W SERIES SPEAKER BRACKETS. FOR MORE INFORMATION CONTACT YOUR
SONOS AUTHORIZED DEALER OR GO TO WWW.OMNIMOUNT.COM.
Pivoting the Speaker
You can rotate the speaker in the bracket to direct the sound
towards the listening area.
1. Unlock the slide locks on the speaker pivots by moving them
towards the rear of the speaker as indicated by the unlock
symbol (see figure 11).
2. Rotate the speakers to the desired position.
3. Lock the slide locks by moving them towards the front of
the speaker as indicated by the lock symbol (see figure 11).
NOTE: BE SURE THAT THE BRACKET CLIPS SNAP COMPLETELY INTO PLACE TO PREVENT ANY
BLOCKAGE WITHIN THE SPEAKER PERIMETER WHERE THE GRILLE IS TO BE INSERTED. PULL THE
SPEAKER GENTLY TOWARD YOURSELF TO VERIFY THAT IT IS SECURELY IN PLACE.
Removing the Speaker
To remove the speaker from the FastMount bracket, gently pull
the grille from each corner until it is freed from the grooves of
the speaker face. Once the grille is removed, remove the wire
connector cover and disconnect the speaker wire from the spring
loaded terminals. Next, use your thumbs to press outward on the
top and bottom tabs of the speaker face, releasing the clips of
the bracket. While pressing the tabs, pull gently on the speaker
away from the bracket.
IMPORTANT: BE SURE NOT TO LET ANY STRAY ‘+’ AND ‘–’ WIRES TOUCH EACH OTHER. TOUCHING
WIRES CAN CAUSE A SHORT-CIRCUIT THAT COULD DAMAGE YOUR AMPLIFIER. Unlocking SONOS Audio
Enhancements
SONOS OUTDOOR by SONANCE speakers include exclusive
audio enhancements when used with a SONOS Amp. Use the free
SONOS app to unlock them.
Audio enhancements include:
Custom EQ settings
Gain adjustment
Dynamic bass extension
Signal limiting/loudspeaker protection

Produktspezifikationen

Marke: Sonos
Kategorie: Lautsprecher
Modell: Outdoor by Sonance

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sonos Outdoor by Sonance benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Lautsprecher Sonos

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-