Silent Knight SK-Zone-6 Bedienungsanleitung

Silent Knight Nicht kategorisiert SK-Zone-6

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Silent Knight SK-Zone-6 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 21 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

SK-460-008 1 I56-3441-002

INSTALLATION AND MAINTENANCE INSTRUCTIONS

I56-3441-002

SK-Zone-6

Six Zone Interface Module

SPECIFICATIONS

Normal Operating Voltage: 15-32 VDC

Stand-By Current: 2 mA

Alarm Current: 40 mA (assumes all six LEDs solid on)

Temperature Range: 32ºF to 120ºF ( 0ºC to 49ºC)

Humidity: 10 to 93% Non-condensing

Dimensions: 6.8˝ H x 5.8˝ W x 1.0˝ D

Accessories: IDP-ACB Cabinet and chassis

Wire Gauge: 12-18 AWG

Max. IDC Wiring Resistance: 25 ohms

External Power Supply Voltage: Regulated 24VDC

Ripple Voltage: 0.1 volts RMS maximum

IDC: (Supervised and power limited)

DC Voltage: 18-28 volts power limited

Frequency: DC

Current: 90mA per circuit

BEFORE INSTALLING

If the modules will be installed in an existing operational system, inform the

operator and local authority that the system will be temporarily out of service.

Disconnect the power to the control panel before installing the modules. This

system contains static sensitive components. Always ground yourself with a

proper wrist strap before handling any circuits so that static charges are re-

moved from the body. The module housing should also be grounded.

NOTICE: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

The SK-Zone-6 Six Zone Interface Module is intended for use in an intelli-

gent alarm system. Each module provides an interface between the intelligent

alarm system and a conventional alarm system loop. A common SLC input is

used for all modules, and the initiating device loops share a common super-

visory supply and ground. Otherwise, each monitor operates independently

from the others. Each module has its own unique address.

A pair of rotary code switches is used to set the address of the first module

from 01 to 154. The remaining modules are automatically assigned to the next

five higher addresses. Provisions are included for disabling a maximum of two

unused modules to release the addresses to be used elsewhere. Each mod-

ule also has panel controlled bicolor LED indicators. The panel can cause the

LEDs to blink, latch on, or latch off.

DET.

MODEL

COMP. ID DETECTOR

MANUFACTURER

BASE MODEL MAX

DET.

1151 A SYSTEM SENSOR B110LP, B401 20

1451 A SYSTEM SENSOR B401, B401B 20

1451DH A SYSTEM SENSOR DH400 20

2151 A SYSTEM SENSOR B110LP, B401 20

2451 A SYSTEM SENSOR DH400, B401B,

B401

2451TH A SYSTEM SENSOR B401, B401B 20

5451 A SYSTEM SENSOR B401 20

1100 A SYSTEM SENSOR N/A 20

1400 A SYSTEM SENSOR N/A 20

**2100AT A SYSTEM SENSOR N/A 20

2100B A SYSTEM SENSOR N/A 20

2100D A SYSTEM SENSOR N/A 20

2100S A SYSTEM SENSOR N/A 20

2100TB A SYSTEM SENSOR N/A 20

2100TD A SYSTEM SENSOR N/A 20

2100TS A SYSTEM SENSOR N/A 20

2300B A SYSTEM SENSOR N/A 20

2300TB A SYSTEM SENSOR N/A 20

2400 A SYSTEM SENSOR N/A 20

2400TH A SYSTEM SENSOR N/A 20

*2W-B A SYSTEM SENSOR N/A 20

*2W-TB A SYSTEM SENSOR N/A 20

DH100LP A SYSTEM SENSOR N/A 20

*Class B, Style B only; **No Accessory will be supported by 2100AT

COMPATIBLE TwO-wIRE SySTEM SENSOR SMOKE DETECTORS FOR

USE wITh SK-ZONE-6 wITh ZONE IDENTIFIER A

INCLUDED:

(5) 1 x 4 Terminal Blocks (2) 11/4˝ Stand offs (3) Shunts

(4) Machine Screws (1) Long Power Supply Jumper

(2) Nuts

(6) 3.9k Ohm

End of Line Resistors

ShIPPED ON BOARD:

(2) Shunts in Class A/B position

(Shipped in Class B position, remove shunts for Class A)

12 Clintonville Road, Northford, CT 06472

203.484.7161; Fax: 203.484.7118

www.silentknight.com

SK-460-008 2 I56-3441-002

COMPATIBILITy REQUIREMENTS

To ensure proper operation, this module shall be connected to a compatible

Silent Knight system control panel (list available from Silent Knight).

COMPONENTS

The following is a description of the SK-Zone-6 mounting framework:

One or two SK-Zone-6 modules can be installed in a IDP-ACB cabinet•

The IDP-ACB cabinet has a built-in chassis that will accommodate one or two

SK-Zone-6 modules. For cabinet dimensions refer to the IDP-ACB instruction

manual.

The front SK-Zone-6 module positions of each chassis are offset below the rear

SK-Zone-6 module positions so that all of the status indicators are visible.

INSTALLATION STEPS

1. Cabinet Mounting

In a clean, dry area, mount the backbox using the four holes provided •

in the back surface of the cabinet (Figure 2).

567

BASE ADDRESS

ADDRESS

DISABLE

C0234-05

FIGURE 1: IDP-ACB CABINET

BACKBOX

MOUNTING

HOLES

C0235-00

FIGURE 2: TyPICAL MOUNTING hOLE LOCATIONS

2. Module Installation

There are two methods for installing a module in the rear position

of a chassis. Method one is for installation of a rear module only,

when no module will be installed in front of it. Refer to Figure 3 for

instructions. Method two is for installation of a rear module when

another module will be installed in the chassis position in front of

it. Refer to Figures 4a and 4b for method two. All necessary screws

and standoffs are supplied with the modules.

C0237-00

C0225-00

FIGURE 3: INSTALLATION OF REAR MODULE ONLy, METhOD ONE

Step 1: Insert the bottom of the SK-Zone-6 module down into a rear slot on

the chassis.

Step 2: Carefully swing the upper edge of the board back towards the back of

the chassis until it touches the two standoffs.

Step 3: Align two 4-40 screws with the two standoffs and tighten.

Step 4: Address and wire the modules according to the instructions in this

manual.

The steps in Figures 4a and 4b describe and illustrate module installation

when the rear chassis position and the position in front of it will be filled.

Front position installation is possible only if the rear position is filled with a

module.

FIGURE 4A: INSTALLATION OF SK-ZONE-6 MODULE IN A REAR ChAS-

SIS POSITION, METhOD TwO

Step 1: Insert the bottom edge of the SK-Zone-6 module down into a rear slot

of the chassis.

Step 2: Carefully swing the upper edge of the board towards the back of the

chassis until it touches the short standoff attached to the chassis.

Step 3: Align the long standoff with the short standoff and tighten.

C0225-00

FIGURE 4B: INSTALLATION OF SK-ZONE-6 MODULE IN FRONT

ChASSIS POSITION

Step 1: Insert the bottom edge of the SK-Zone-6 module down into a front

slot of the chassis.

Step 2: Carefully swing the upper edge of the board

towards the back of the chassis until it touches the 11/4˝ (31.75mm)

standoffs installed on the rear module.

Step 3: Align two 4-40 screws with the two standoffs and tighten.

Step 4: Address and wire the modules according to the instructions in this

manual.

wIRING

NOTE: All wiring must conform to applicable local codes, ordinances, and

regulations.

1. Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams.

2. All wiring to the SK-Zone-6 is done via terminal blocks. In order to prop-

erly make electrical connections strip approximately 1/4˝ of insulation

from the end of wire, sliding the bare end of the wire under the clamping

plate screw.

3. Set the address on the modules per the job drawing. Use the rotary code

switches to set the address of the first module between 01 and 154.

SK-460-008 3 I56-3441-002

In Class B operation, the remaining modules are automatically assigned to the

next five higher addresses. For example, if the base address switch is set to 28,

the next five modules will be addressed to 29, 30, 31, 32 and 33.

The module is shipped in Class B position, remove shunts for Class A. When

operating in Class A, alternate modules are paired together (+0/+1, +2/+3,

+4/+5), resulting in a total of three modules. For example, if the base ad-

dress switch is set to 28, then 30 and 32 will be automatically assigned to the

modules while 29, 31 and 33 are available to be used for other modules on the

SLC. For Class A and B operation, DO NOT set the lowest address above 154,

as the other modules will be assigned to nonexistent addresses.

NOTE: The SK-Zone-6 must have power cycled for shunt changes to take effect.

4. A shunt is provided to disable a maximum of two unused modules in

Class B operation and Class A operation. Modules are disabled from the

highest address and work downward. If two modules are disabled, the

lowest four addresses will be functional, while the highest two will be dis-

abled. For example, in Class B operation, if the shunt for Address Disable

is placed on “two” and the base switch is set to 28, the modules will be

assigned to 28, 29, 30 and 31 while disabling the highest two positions.

NOTE: Place unused shunts on single pin to store on board for future use.

BASE ADDRESS

TO NEXT DEVICE

–

S TUS TA

INDICATORS

—

IDC

ADDRESS

—

IDC

ADDRESS

—

IDC

ADDRESS

SLC

—

–

FROM PANEL OR

PREVIOUS DEVICE

3.9K EOL

RESISTOR

(INCLUDED)

CONNECT MODULES TO

LISTED COM TIBLE PA

SILENT KNIGHT CONTROL

PANELS ONLY

SIGNAL LINE CIRCUIT (SLC) 32 VDC MAX.

SEE PANEL INSTRUCTION MANUAL

FOR WIRE REQUIREMENTS.

CLASS B IDC (TYPICAL)

A/B SELECT

DISABLE 1

DISABLE 2

–

T6 T5

DETECTORS MUST BE UL LISTED COM TIBLE WITH THE MODULE. PA

INSTALL DETECTORS PER MANUFACTURER'S INSTALLATION INSTRUCTIONS.

(–)

(+)

OUT

—

EXTERNAL SUPPLY

POWER-LIMITED

AND SUPERVISED

POWER THE NEXT INTERFACE TO

MODULE MUST BE EXTERNALLY

SWITCHED RESET THE DETECTORS. TO

AN FRM-1 RELAY CONTROL MODULE CAN BE

USED SWITCH POWER FROM TO A

STANDARD POWER SUPPLY. SEE FIGUR 10.

4567 8 9

45678910

wIRING NOTES

Power-limited circuits must employ type FPL, FPLR, or FPLP cable as •

required by Article 760 of the NEC.

All wiring must be in accordance with the NEC, NFPA 72 and all other •

applicable codes and standards. All external power supplies must be

power limited with battery back-up. All external power supplies and

detectors must be UL listed for fire protection signaling applications.

PROGRAMMING

The modules are programmed as devices in each system according to the pro-

gramming instructions in the appropriate FACP manual.

FIGURE 5: INTERFACE TwO-wIRE CONvENTIONAL DETECTORS – CLASS B, STyLE B.

C0812-01

1. To use a common power sup-

ply between multiple SK-Zone-6

modules, connect a long power

supply jumper from T5 or T6

to T5 or T6 on the adjacent SK-

Zone-6 module.

BASE ADDRESS

TO NEXT DEVICE

–

S TUS TA

INDICATORS

—

IDC

ADDRESS

—

IDC

ADDRESS

—

IDC

ADDRESS

SLC

—

–

FROM PANEL OR

PREVIOUS DEVICE

CONNECT MODULES LISTED COM TIBLE TO PA

SILENT KNIGHT CONTROL PANELS ONLY

SIGNAL LINE CIRCUIT (SLC) 32 VDC MAX.

SEE PANEL INSTRUCTION MANUAL

FOR WIRE REQUIREMENTS.

CLASS IDC (TYPICAL) A

A/B SELECT

DISABLE 1

DISABLE 2

+ + IDC 2

IDC 3

(–)

(+)

POWER THE NEXT INTERFACE TO

MODULE MUST BE EXTERNALLY

SWITCHED RESET THE DETECTORS. TO

AN FRM-1 RELAY CONTROL MODULE CAN BE

USED SWITCH POWER FROM TO A

STANDARD POWER SUPPLY. SEE FIGURE 10.

T6 T5

OUT

—

EXTERNAL SUPPLY

POWER-LIMITED

AND SUPERVISED

– –

DETECTORS MUST BE UL LISTED COM TIBLE WITH THE MODULE. INSTALL PA

DETECTORS PER MANUFACTURER'S INSTALLATION INSTRUCTIONS.

4567 8 9

FIGURE 6: INTERFACE TwO-wIRE CONvENTIONAL DETECTORS – CLASS A, STyLE D.

C0813-01

1. To select Class A, remove the

two shunts from the “A/B se-

lect” positions.

2. To use a common power sup-

ply between multiple SK-Zone-6

modules, connect a long power

supply jumper from T5 or T6

to T5 or T6 on the adjacent SK-

Zone-6 module.

Produktspezifikationen

Marke:	Silent Knight
Kategorie:	Nicht kategorisiert
Modell:	SK-Zone-6

Brauchst du Hilfe?

Wenn Sie Hilfe mit Silent Knight SK-Zone-6 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Silent Knight

Silent Knight PS-SA Bedienungsanleitung

30 August 2024

Silent Knight FFT-HSC Bedienungsanleitung

30 August 2024

Silent Knight SK-NIC-KIT Bedienungsanleitung

30 August 2024

Silent Knight SD500-PSDA Bedienungsanleitung

13 März 2024

Silent Knight SK-Zone-6 Bedienungsanleitung

24 Februar 2024

Silent Knight SD500-PS Bedienungsanleitung

20 Februar 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024