Siig CE-MT0A12-S1 Bedienungsanleitung

Siig Wandstütze CE-MT0A12-S1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Siig CE-MT0A12-S1 (8 Seiten) in der Kategorie Wandstütze. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
A B C D E F G
(x2) M6X60
bolt
(x2) M6 concrete
anchor
(x4) M6 small
washer
(x2) M6 large
washer
(x4) M4X12
screw
(x4) M5X12
screw
(x4) M6X12
screw
4mm Allen Key 6mm Allen Key
04-0553C
LCD TV/Monitor Tilting Mount - 10" to 26"
Hardware
Installation Instructions
Tools Required: Electronic stud finder, #2 Phillips head screw driver, drill, 1/8" drill bit (wood
stud installation), 3/8" masonry drill bit (concrete/brick wall installation).
Page 1
1
2
3
4
Figure 1 Figure 2
1
2
3
Step 1: Wall Plate Installation
Hold the wall plate (Figure 2) to the wall, use the two mounting holes to mark the
locations to be used for mounting the wall plate. Locate the holes directly into the
brick, block or concrete, never into the mortar between the blocks.
Pre-drill two holes to a depth of 2" using a 3/8" masonry drill bit at the positions you've
marked and insert one concrete anchor (B) into each hole.
Position the wall plate onto the wall again and insert the bolts (A) and washer (D) into
the anchor as shown (Figure 2) and tighten.
Use a high-quality electronic stud finder (commercially available) to locate dead center
of the wood stud and mark the location with a pencil.
Wood Stud Installation
Concrete/Brick Wall Installation
Attach the wall plate to the wall again and insert the bolts (A) and washers (D) into the
holes (Figure 1) and tighten.
Hold the wall plate (Figure 1) to the wall, use the two mounting holes to mark the
locations to be used for mounting the wall plate.
Take down the wall plate and drill two 2" deep holes, using a 1/8" drill bit at the
positions you've marked.
Page 2
1
2
Figure 3
1
2
3
Figure 4
Phillips
screw driver
Figure 5 Figure 6 Figure 7
Step 3: Final Installation
Step 2: Display Plate Installation
Hang the display plate onto the top of the
wall plate and slip it into the wall plate as
shown (Figure 4).
Tighten the safety screw on the side and
back using a Phillips head screw driver
and the supplied 4mm Allen Key (Figure 5
& Figure 6 respectively).
Place your TV screen down on a soft, flat surface, and locate the threaded mounting
points that are located on the back of the display.
According to the size of the display's hole, choose the corresponding screw (E/F/G)
and washer (C) and insert into the hole as shown (Figure 3) and tighten.
Adjust the tension of the joint using the
supplied 6mm Allen Key (Figure 7).
Page 3


Produktspezifikationen

Marke: Siig
Kategorie: Wandstütze
Modell: CE-MT0A12-S1
Produktfarbe: Schwarz
Befestigungstyp: Wand
Höchstgewichtskapazität: 15 kg
Panel-Montage-Schnittstelle: 50 x 50, 75 x 75, 100 x 100 mm
Neigungswinkelbereich: -45 - 45 °
Projektionsflächenkapazität: 10 - 26 Zoll
Kompatibilität: LCD TV/monitor
Minimale VESA-Halterung: 50 x 50 mm
Maximale VESA-Halterung: 100 x 100 mm

Brauchst du Hilfe?

Wenn Sie Hilfe mit Siig CE-MT0A12-S1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Wandstütze Siig

Bedienungsanleitung Wandstütze

Neueste Bedienungsanleitung für -Kategorien-