Siig CE-MT0712-S1 Bedienungsanleitung

Siig Wandstütze CE-MT0712-S1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Siig CE-MT0712-S1 (8 Seiten) in der Kategorie Wandstütze. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

04-0529C

IMPORTANT: If you don't understand the installation instructions, please

consult an installation specialist

Tiltable LCD / TFT TV Wall Mount

Material: 2.0mm Cold Rolled Steel Plate

TV Size: 32" - 60"

Tilt: 0 / +15 degrees

Maximum load capacity: 165 lbs / 75 kgs

Wall distance: 3.3" / 84mm

Bubble level system included

Universal Mounting Pattern

Installation Instructions

Universal Tilting TV Mount - 32" to 60"

A-1 G

A-2 (x1) Key H

B I

C J

D K

E L

F M (×4) M8 Spacer

1 Phillips head screw driver

2 Stud finder for drywall installation

3 5/16" Socket and Wrench

4 Electric drill and 5/16"(8mm) masonry bit for concrete/brick installation

(×4) M4×12 screw

Caution

CAUTION: The maximum load capacity is 165 lbs. Use with products heavier than the maximum load capacity

may cause serious injury. See apparatus instructions.

Prior to the installation of this product, the installation instructions should be read and completely understood.

The installation instructions must be read to prevent personal injury and property damage. Keep these

installation instructions in an easily accessible location for future reference.

Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any

surface other than wood studs, use suitable hardware (not included but commercially available).

Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could

result in damage to the display and/or damage to the mounting surface.

Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source.

Failure to do so may result in damage to the display and could increase the risk of fire.

The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the

wall must be reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in

the installation instructions, must be adhered to. Failure to do so could result in serious personal injury.

(×4) M5×16 screw

(×4) M8×16 screw

(×4) M8×35 screw

Tools Required:

INSTALLATION AND OPERATING INSTRUCTIONS

(×4) M6×35 screw

(×4) M6×16 screw

Hardware kit:

(×4) M4×16 screw

It is recommended that two people perform the installation. Injury and/or damage can result from dropping or

mishandling the display.

(×4) M8/M6/M5 Washer

(×6) M8x80 Bolt

(×6) M8 Concrete Anchor

When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it

is recommended that the wood studs be a minimum of 16" apart.

(×6) M8 Washer

(×4) M4×35 screw

Note:

Step 1: Wall plate installation

4 You should mark four positions total.

CAUTION:

Use a high-quality electronic stud finder (commercially available)

to locate two adjacent studs and mark their locations with a pencil

(1-a).

Pre-drill a 1/4" hole to a depth of 2" in the wall stud at each

marked location.

NOTE: For secure wood stud mounting, the wall plate must be mounted to two studs at least

16" apart.

For each location, insert a lag bolt (J) and washer (L) into the wall.

Tighten each bolt with an open ended socket wrench by turning clockwise until tight.

Do not release the wall plate until it is properly mounted and secured to the wall.

Do not over-tighten bolts-doing so many cause unnecessary damage to the wall. Avoid excessive

torque.

Mark the right (upper and lower) and the left (upper and lower)

positions of the small horizontal slots that are in alignment with

the studs.

Position the wall plate against the wall and line up the mounting

slots with the drilled holes. Check the bubble level to verify that

the wall plate is level.

A) Wood Stud Installation

1. Please ensure that the bubble level is properly mounted on the wall

plate prior to mounting the wall plate.

2. Please check the two rails before installing, if without the

knob, please detach the screw and install the knob.

With the help of an assistant, and using the bubble level to

ensure the wall plate is level, position the wall plate against the

wall in the desired mounting location.

Produktspezifikationen

Marke:	Siig
Kategorie:	Wandstütze
Modell:	CE-MT0712-S1
Breite:	494 mm
Tiefe:	84 mm
Gewicht:	4100 g
Produktfarbe:	Schwarz
Höhe:	820 mm
Befestigungstyp:	Wand
Höchstgewichtskapazität:	75 kg
Zertifizierung:	UL
Gehäusematerial:	Metall
Neigungswinkelbereich:	0 - 15 °
Projektionsflächenkapazität:	32 - 60 "