Siemens WD14H420EU iQ500 Was/Droogcombi Bedienungsanleitung
Siemens
Was/Droogcombi
WD14H420EU iQ500 Was/Droogcombi
Lesen Sie kostenlos die π deutsche Bedienungsanleitung fΓΌr Siemens WD14H420EU iQ500 Was/Droogcombi (8 Seiten) in der Kategorie Was/Droogcombi. Dieser Bedienungsanleitung war fΓΌr 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8
1
Safety instructionsξξξξξ
ξ The washer dryer is heavy ξ take care when lifting it.
ξ Warning: frozen hoses may tear/burst. Do not install the washer dryer outdoors or in areas
where there is a risk of frost.
ξ The washer dryer may be damaged. Do not lift by projecting components (e.g. washer dryer
door).
ξ In addition to the instructions mentioned here, special regulations of the relevant water and
power supply companies may apply.
ξ If in doubt, have the appliance connected by a technician.
ξ Lay hoses and cables in such a way that there is no risk that they can be tripped over.
Environmental disposal
ξξ Dispose of packaging in an environmentally friendly manner.
ξ This appliance has been identified in accordance with the European Directive
2002/96/EEC on Waste Electrical and Electronic Equipment (WEEE). The Directive
specifies aΓ’framework for the return and recycling of waste appliances and is valid
throughout Europe.
Scope of delivery according to model Humidity in the drum is caused
byΓ’the final inspection.
Depending on the connection
ξ AΓ’24ξ40 mm dia. hose clip may also be required for connecting the siphon (available from
specialist retailers). aPageΓ’4:Water connection
Useful tool
ξ Spirit level for aligning the washer dryer.
ξ Wrench for adjusting the machine feet.
Water drainage
Power cord
Water supply
Covers
Hose holder
Aqua-Stop Aqua-Secure Standard
2
Installation area
ξ Stability is important to prevent the machine from wandering.
ξ The installation area must be firm and level.
ξ Soft floors/floor coverings are not suitable.
ξ Ensure the area is well ventilated to achieve good drying performance.
If installing the appliance on a pedestal
ξ It is essential to secure the washer dryer feet with holding bracketsΓ’*.
If installing the appliance on a wooden joist floor
ξ If possible, install the washer dryer in a corner.
ξ Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
ξ It is essential to secure the washer dryer feet with holding bracketsΓ’*.
*Γ’order no. WMZ 2200, WX 9756
Hose and cable lengths
ξ
ξξ
Connection on left sideξ or ξξξξξξξConnection on right side
Note: if hose holders are used, the hose lengths may be reduced.
Available from dealer/customer service:
ξ Aqua-Stop extension hoseΓ’**, approx. 2.50 m.
ξ Longer supply hose, approx. 2.20 m, for standard model.
**Γ’order no. WMZ 2380, WZ 10130
Built-under/Built-in appliance
ξBuild-under/build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
ξ Dimension requirement of kitchen unit:
aΓ’=Γ’650Γ’mm,bΓ’=Γ’620Γ’mm,cΓ’=Γ’850Γ’mm
ξ Install washer dryer only under a continuous worktop that
is connected firmly to the adjacent cupboards.
ξ The installation area must be well ventilated, otherwise the
washer dryer will operate below optimum performance.
Dimension of ventilation cross-section:
d x e = 200 mm x 100 mm,f = 365Γ’mm
Distance between wall and machine: 50Γ’mm
~140 cm
~160 cm
~140 cm
~90 cm
~165 cm
~95 cm
max. 100 cm
min. 60 cm
f
e
3
Removing transport bolts
ξ Before using the appliance for the first time, always remove and retain
all 4 transport bolts.
ξ If transporting the appliance subsequently, always re-install the
transport bolts ξ this prevents damage to the machine. aPageΓ’6
ξ Retain the screw and sleeve.
1. Take the hoses out of the holder and the elbow.
2. Undo and remove all 4 transport bolts.
3. Take the power cord out of the holders. Remove the sleeves.
4. Insert the covers and lock them in place by pressing on the locking hook. Insert the hose
holders.
5. Fix the hoses in the hose holders.
4
Water connection
ξ
ξ Risk of electric shock! Do not immerse the Aqua-Stop safety device in water
(containsΓ’anΓ’electric valve).
ξ To prevent leakage or water damage, follow the instructions in this chapter.
ξAttention: operate the washer dryer with cold drinking water only.
Do not connect to the mixer tap of a pressureless hot-water heater.
ξ Do not use a used inlet hose. Only use the inlet hose supplied or one which
was purchased from an authorised specialist dealer.
ξ If in doubt, have the appliance connected by a technician.
Water supply
Water inlet hose:
Attention: do not kink, crush, modify or cut through (strength is no longer guaranteed).
Optimum water pressure in the mains: 100ξ1000 kPa (1ξ10 bar)
ξ When the tap is turned on, the water flow is at least 8 l/min.
ξ If the water pressure is higher, install a pressure reducing valve.
Model: Aqua-Stop
Aqua-Secure
Standard
1. Connect the water supply hose to the tap.
Tighten plastic screw fittings by hand only.
2. Carefully turn on the tap and check that the
connection points are not leaking.
Attention: the screw connection is under
water mains pressure.
Water drainage
Water drainage hose:
Attention: do not kink or stretch.
Height difference between installation area and outlet: 60ξ100 cm
Drainage into a sink/bath tub:
Attention: secure the drainage hose to prevent it from slipping out
ofΓ’theΓ’sink.
Attention: the plug must not be in the plug hole. When the water is being
pumped out of the washer dryer, check that the water drains away quickly
enough. Do not immerse the end of the drainage hose in the water that has
been pumped out. There is a risk that water will be drawn back into the
washer dryer.
Drainage into a siphon:
Attention: secure the connection with a 24ξ40 mm dia. hose clip (available
from a specialist retailer).
Drainage into a plastic pipe with rubber sleeve:
Attention: Secure the drainage hose to prevent it from slipping out
ofΓ’theΓ’drain.
3/4
ξξ
min. 10 mm
max.
90Β°
max.
90Β°
3/4
ξξ
min 10 mm
5
Manufacturer (see Operating instructions) 0312 / 9000 479252
Alignment
High levels of noise, intense vibrations and ξwanderingξ may be due to incorrect alignment.
Alignment will be carried out by customer service or authorised technicians, if you want
toΓ’align the machine by yourself please use a spirit level.
Aligning the washer dryer with a spirit level.
1. Undo the lock nut in a clockwise direction using a wrench.
2. Adjust the height by turning the appliance foot.
All four appliance feet must be placed firmly on the floor.
The washer dryer must not be able to wobble.
Check the alignment of the washer dryer with a spirit level andΓ’
correct if necessary.
3. Tighten the lock nut against the housing.
Hold the foot in place and make sure that the height is not adjusted.
The lock nuts on all four appliance feet must be screwed tightly against
the housing.
Electrical connection
ΚConnect the washer dryer to an alternating current via a correctly installed earthed socket
only.
ΚThe mains voltage and specifications on the washer dryer must match.
aPageΓ’6: Technical specifications
ΚFor information about the connected load and required fuse.
aPageΓ’6: Technical specifications
ΚEnsure that:
ξ the mains plug and socket are compatible,
ξ the cable cross-section is adequate,
ξ the earthing system has been installed correctly.
ΚA damaged power cord may be replaced by an electrician only.
A replacement power cord is available from customer service.
ΚDo not use multiple plugs/connectors or extension cables.
ΚIf a residual current operated circuit-breaker is used, use only a type which guarantees
compliance with the currently valid regulations.
ΚMains plug:
ξ do not insert into/pull out of the socket with damp hands.
ξ do not pull the plug out of the socket by pulling on the power cord.
ξ never pull out the plug while the appliance is in operation.
6
Transportation, e.g. if moving houseξξ
Before transporting the washer dryer:
1. Turn off the tap.
2. Release the water pressure in the supply hose.
aPageΓ’8: Filter in the water inlet hose
3. Drain any residual detergent solution.
aPageΓ’8: Drain pump
4. Isolate the washer dryer from the power supply.
5. Remove the hoses.
Installing transport bolts:
1. Remove the covers. If necessary, remove the
retainer according to the right picture.
2. Insert all 4 sleeves.
Clamp the power cord into
the holders.
Insert the screws and
tighten.
The transport bolts must be removed after transportation. aPageΓ’3
To prevent unused detergent from flowing into the outlet during the next wash:
Pour 1 litre of water into dispenser II and start the Empty (Drain)or Spin programme.
Technical specifications
ΚDimensions (width x depth x height) 600 x 600 x 850 mm
ΚWeight 84,5 kg
Κ
Power supply
Nominal voltage 220ξ240Γ’V, 50 Hz
Max. current 10A
Max. washing power 2400 W
Max. drying power 1900 W
ΚWater pressure 100ξ1000 kPa (1ξ10 bar)
ΚDrain height 60ξ100 cm
ΚTest programmes According valid European Standard EN50229
1.
2.
7
Care
Machine housing, control panel
ξ Wipe with a soft, damp cloth.
ξ Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
ξ Immediately remove laundry and cleaning agent residues.
ξ Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener residue.
1. Pull out the drawer up to the stop position, press down the latch
onΓ’theΓ’insert and remove the drawer completely.
2. Remove insert: pull insert upwards with finger.
3. Clean the detergent dispenser and the insert with water and a brush.
4. Refit the insert and secure in place (the cylinder should fit over the
guideΓ’pin).
5. Insert the detergent drawer.
6. Leave the detergent drawer open so that residual water can evaporate.
Drum
Leave the washer dryer door open after washing so that the drum can dry.
Rust stains ξ use chlorine-free cleaning agent, not steel wool.
Descaling ξ No laundry in the machine!
This is not necessary if the detergent is dosed correctly. However, if it is necessary, follow the
instructions of the descaler manufacturer. Suitable descaling products can be purchased
from our website or after-sales service.
After-sales service
ΚIf you cannot rectify the fault yourself aOperating instructions, page 12, 13: What to do if...,
please contact our after-sales service. We will always find a suitable solution and will avoid a
visit from a service technician wherever possible.
ΚThe contact details for all countries can be found in the enclosed after-sales service directory.
ΚPlease give the after-sales service the product number (E-Nr.) and the production number
(FD) of the appliance.
Product number Production number
You will find this information:
on the inside of the washer dryer door*/opened
service flap* and rear of the appliance.
*depending on the model
ΚRely on the professionalism of the manufacturer. Please contact us.
This will ensure that the repair is carried out by trained service technicians who arrive
equipped with genuine spare parts for your appliance.
ξ Risk of electric shock!
Pull out the mains plug!
ξ Risk of explosion! No solvents!
8
Maintenance
Drain pump
Set the programme selector to Off, disconnect the mains plug.
1. Open and remove the service flap.
2. Release the drainage hose from the clip.
Remove the sealing plug from the drainage hose, allow the detergent
solution to flow out. Push the sealing cap back in.
3. Remove the pump cap. Remove foreign objects/loose debris/fluff from
inside and clean the pump. (impeller in the pump must be able to rotate).
4. Clean any residual lye or fluff from the thread of the pump cap
andΓ’pumphousing.
5. Attach the pump cap and screw it on tight until the stop, handle is upright.
Place the drainage hose back in the retainer.
6. Place the service flap back on and close.
To prevent unused detergent from flowing straight into the drain during
the next wash cycle: pour 1 litre of water into compartment II and start
the Spin programme. Then select and start a new washing programme
with detergent as usual.
Filter in the water inlet hose
Risk of electric shock
Do not immerse the Aqua-Stop safety device in water (it contains an electric valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except Spin or Empty(Drain)).
3. Touch Start button and allow the programme to run for approx. 40 seconds.
4. Set the programme selector to Off.Disconnect the mains plug.
ξ Clean the filter:
1. Depending on model: Remove the supply hose from the tap.
Clean the filter with a small brush.
and/or on standard and Aqua-Secure models:
Remove the hose from the rear, remove the filter
using pliers and clean the filter.
2. Reconnect the supply hose and check if it
is tight.
ξ Risk of scalding!
Allow detergent solution to cool down!
ξ Turn off the tap!
9
Maintenance
Air inlet filter
Set the programme selector to Off, disconnect the mains plug.
1. Open and remove the service flap.
2. Remove the air inlet filter.
3. Clean the fluff on the air inlet filter with water and a brush.
4. Place the air inlet filter back on and close.
5. Place the service flap back on and close.
Aqua-Stop warranty for appliances with Aqua-Stop only
In addition to warranty claims against the seller based on the contract of sale and in addition
to our appliance warranty, we shall pay damages under the following conditions:
1. If water damage was caused by a fault in our Aqua-Stop system, we shall compensate private
users for damage.
2. The liability warranty applies to the service life of the appliance.
3. A claim can only be made under the warranty if the appliance and Aqua-Stop have been
correctly installed and connected according to our instructions; this also includes a correctly
installed Aqua-Stop extension (genuine accessory).
Our warranty does not extend to defective supply lines or fittings up to the Aqua-Stop
connection on the tap.
4. Appliances which feature Aqua-Stop can be left unattended during operation and it is not
necessary to turn off the tap afterwards.
The tap should only be turned off if you are away for a prolonged period, e.g. several weeks
holiday.
Contents Page
ΚSafety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ΚEnvironmental disposal . . . . . . . . . . . . . . . . . . . . . . . . . 1
ΚScope of delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ΚInstallation area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ΚHose and cable lengths . . . . . . . . . . . . . . . . . . . . . . . . 2
ΚBuilt-under/Built-in appliance . . . . . . . . . . . . . . . . . . . . . 2
ΚRemoving transport bolts . . . . . . . . . . . . . . . . . . . . . . . 3
ΚWater connectionξ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ΚAlignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ΚElectrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ΚTransportation, e.g. if moving house . . . . . . . . . . . . . . . 6
ΚTechnical specifications. . . . . . . . . . . . . . . . . . . . . . . . . 6
ΚCare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ΚAfter-sales serevice . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ΚMaintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8/9
ΚAqua-Stop warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Washer dryer en
Read these instructions before switching on the washer dryer.
Also follow the separate Operating instructions.
Retain all documents for subsequent use or for the next owner.
Installation maintenance
instructions
1
Safety instructionsξξξξξ
ξ The washer dryer is heavy ξ take care when lifting it.
ξ Warning: frozen hoses may tear/burst. Do not install the washer dryer outdoors or in areas
where there is a risk of frost.
ξ The washer dryer may be damaged. Do not lift by projecting components (e.g. washer dryer
door).
ξ In addition to the instructions mentioned here, special regulations of the relevant water and
power supply companies may apply.
ξ If in doubt, have the appliance connected by a technician.
ξ Lay hoses and cables in such a way that there is no risk that they can be tripped over.
Environmental disposal
ξξ Dispose of packaging in an environmentally friendly manner.
ξ This appliance has been identified in accordance with the European Directive
2002/96/EEC on Waste Electrical and Electronic Equipment (WEEE). The Directive
specifies aΓ’framework for the return and recycling of waste appliances and is valid
throughout Europe.
Scope of delivery according to model Humidity in the drum is caused
byΓ’the final inspection.
Depending on the connection
ξ AΓ’24ξ40 mm dia. hose clip may also be required for connecting the siphon (available from
specialist retailers). aPageΓ’4:Water connection
Useful tool
ξ Spirit level for aligning the washer dryer.
ξ Wrench for adjusting the machine feet.
Water drainage
Power cord
Water supply
Covers
Hose holder
Aqua-Stop Aqua-Secure Standard
2
Installation area
ξ Stability is important to prevent the machine from wandering.
ξ The installation area must be firm and level.
ξ Soft floors/floor coverings are not suitable.
ξ Ensure the area is well ventilated to achieve good drying performance.
If installing the appliance on a pedestal
ξ It is essential to secure the washer dryer feet with holding bracketsΓ’*.
If installing the appliance on a wooden joist floor
ξ If possible, install the washer dryer in a corner.
ξ Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
ξ It is essential to secure the washer dryer feet with holding bracketsΓ’*.
*Γ’order no. WMZ 2200, WX 9756
Hose and cable lengths
ξ
ξξ
Connection on left sideξ or ξξξξξξξConnection on right side
Note: if hose holders are used, the hose lengths may be reduced.
Available from dealer/customer service:
ξ Aqua-Stop extension hoseΓ’**, approx. 2.50 m.
ξ Longer supply hose, approx. 2.20 m, for standard model.
**Γ’order no. WMZ 2380, WZ 10130
Built-under/Built-in appliance
ξBuild-under/build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
ξ Dimension requirement of kitchen unit:
aΓ’=Γ’650Γ’mm,bΓ’=Γ’620Γ’mm,cΓ’=Γ’850Γ’mm
ξ Install washer dryer only under a continuous worktop that
is connected firmly to the adjacent cupboards.
ξ The installation area must be well ventilated, otherwise the
washer dryer will operate below optimum performance.
Dimension of ventilation cross-section:
d x e = 200 mm x 100 mm,f = 365Γ’mm
Distance between wall and machine: 50Γ’mm
~140 cm
~160 cm
~140 cm
~90 cm
~165 cm
~95 cm
max. 100 cm
min. 60 cm
f
e
aΓ’
ξ
Γ’ Γ’
Γ’ Γ’
Γ’ Γ’
Γ’
Γ’
Κ
ΚaΓ’
ΚaΓ’
Κ
Κ
Κ
Κ
Κ
Produktspezifikationen
| Marke: | Siemens |
| Kategorie: | Was/Droogcombi |
| Modell: | WD14H420EU iQ500 Was/Droogcombi |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Siemens WD14H420EU iQ500 Was/Droogcombi benΓΆtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Was/Droogcombi Siemens
Bedienungsanleitung Was/Droogcombi
- Was/Droogcombi Bosch
- Was/Droogcombi Bauknecht
- Was/Droogcombi Electrolux
- Was/Droogcombi BEKO
- Was/Droogcombi Grundig
- Was/Droogcombi Candy
- Was/Droogcombi Hoover
- Was/Droogcombi Hotpoint-Ariston
- Was/Droogcombi Indesit
- Was/Droogcombi Zanker
- Was/Droogcombi Zanussi
- Was/Droogcombi Zanussi-Electrolux
Neueste Bedienungsanleitung fΓΌr -Kategorien-
25 August 2024
24 August 2024
24 August 2024
24 August 2024
23 August 2024
22 August 2024
5 August 2024
6 Juli 2024