Sharp XE-A101 Bedienungsanleitung

Sharp Registrierkassen XE-A101

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sharp XE-A101 (4 Seiten) in der Kategorie Registrierkassen. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

5. Attach the printer cover.

CImproper use of batteries could cause

them to burst or leak, which might damage

the interior of the cash register. Please

take the following precautions:

Be sure that the positive (+) and negative

(-) poles of each battery are oriented

properly. .

•Never mix batteries of different types.

•Never mix old batteries and new ones.

•Never leave dead batteries in the battery

compartment.

•Remove the batteries if you plan not to

use the cash register for long periods.

Should a battery leak, clean out the

battery compartment immediately, taking

care not to let the battery fluid come into

direct contact with your skin.

Installing a Paper Roll

Always install the paper roll even when you set the

mode.

1. Push the printer cover forward and detach it.

2. Push the paper roll release lever and install

the paper roll so that the paper unrolls from

the bottom.

Tax 1

SBTL @/TM @/TM

Tax rate(7.0000%) Min. taxable

amount($0.11)

Changing Other Settings As Necessary

Your cash register is pre-programmed so that you

can use it with minimum setup. To change the initial

settings, see the appropriate sections.

Initial Settings

Departments 1 to 4:

Taxable 1. Positive (+). Preset price: 0.00

Departments 5 to 8:

Non-taxable. Positive (+). Preset price: 0.00

PLU codes 1-10:

Assigned to dept. 1. Preset price: 0.00

PLU codes 11-80:

Not used

When you program the tax status for a department,

tax will be automatically added to sales of items

assigned to the department according to the

programmed tax status for the department. You can

also enter tax manually.

There are two tax programming methods. The tax

rate method uses a straight percentage rate per

dollar. The tax table method requires tax break

information from your state or local tax offices. Use

the method which is acceptable in your state. You

can obtain necessary data for tax programming from

your local tax office.

D For tax table programming, see "programming"

Tax Rate Programming

The percent rate specified here is used for tax

calculation on taxable subtotals. Set the mode

switch to the Z/PGM position and use the following

sequence to program the tax rate:

➝#/

SBTL ➝ Tax number(1-4) ➝

@/TM

➝ R

➝

@/TM

➝ Q ➝

where R and Q represent the following.

R: Tax rate (0.0000% to 99.9999%) x 10000

Enter the rate in 6 digits (leading zeros may be

omitted). If the rate is fractional (e.g., 4 3/8%), it

should be converted to its decimal equivalent

(4.375) before entering.

Q: Minimum taxable amount (0.01 to 99.99) x 100

Smallest amount for which tax must be collected. In

some states, sales whose amounts are less than the

minimum taxable amount are not subject to tax. If

amounts $0.01 to $0.10 are not taxed, the value of

Q would be 11 (for $0.11), the lowest of the first

taxable category.

Time(2:30 p.m.)

SBTL

DDD Always enter the date in 6 digits. For

example, enter

for March

15, 2002. If you change the date format in

the Z/PGM mode, follow the newly specified

format when setting the date.

Checking the Time and Date

You can display the time and date to check if they

are correctly set.

1. Set the mode switch in the REG position.

2. Press the

@/TM

key once to display the time.

3. Press the

@/TM

key a second time to display the

date.

Programming the Tax Rate

Before you can proceed with registration of sales,

you must first program the tax that is levied in

accordance with the law of your state. Your cash

different tax rates. In most states, you will only

need to program Tax 1. However, if you live in an

area that has a separate local tax (such as a Parish

tax) or a hospitality tax, your register can be

programmed to calculate these separate taxes.

In order to program the tax to be collected in

accordance with the law of your state, you must

specify the tax rate(s) and minimum taxable

amount(s).

D•Always enter the time in 4 digits even when

the hour is in the single digit. For example,

enter

for 6:30 a.m.

• “ ” 6:30 a.m. prints as 6-30 and 6:30 p.m.

prints as “6-30@”.

Setting the Date

In the Z/PGM mode, enter the date in 6 digits using

the month-day-year format. Press the

SBTL

key once

to continue programming or twice to exit the

program mode.

5. Attach the printer cover.

(For receipt printing, step 4 should be omitted.)

Setting the Time

Set the mode switch to the Z/PGM position and

enter the time in 4 digits ( format) using the“hhmm”

24 hour system. Press the

SBTL

key once to continue

programming or twice to exit the program mode.

3. Insert three new AA batteries.

Initializing the Cash Register

For your cash register to operate properly, you must

initialize it before programming for the first time.

Follow this procedure.

1. Remove the register from its packing carton.

2. Set the mode switch to the REG position.

3. Insert the plug into the AC outlet.

IMPORTANT: This operation must be performed

without batteries loaded.

4. The buzzer will sound three times. Now your

cash register has been initialized. The display

will show "0.00" with “lllll”.

Installing Batteries

Batteries must be installed in the cash register to

prevent data and programmed contents from being

lost from the memory in case of accidental

disconnection of the AC cord or power failure. Please

install three new batteries before programming“AA”

and operating the cash register. Once installed, the

batteries will last approximately one year. When it is

time to replace them, the symbol will appear on“ ”l

the display to indicate a low battery voltage. If the

symbol appears, you must replace them within two

days.

Install the batteries according to this procedure with

the AC cord connected:

1. Push the printer cover forward and detach it.

4. When the batteries are properly installed, “lllll”

on the display will disappear. Close the battery

cover.

Thank you for purchasing the SHARP Electronic Cash Register Model XE-A101. Please

read this manual carefully before operating your machine. Keep this manual for future

reference. It will help you solve any operational problems that you may encounter.

For assistance call

1-800-BE-SHARP

SHARP ELECTRONIC CASH REGISTER MODEL

XE-A101

INSTRUCTION MANUAL

WARNING

FCC Regulations state that any unauthorized changes or modifications to this equipment not

expressly approved by the manufacturer could void the user’s authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when this equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

CAUTION

The socket-outlet shall be installed near the equipment and shall be easily accessible.

FOR YOUR RECORDS

Please record below the model number and serial number, for easy reference, in case of loss or theft.

These numbers are located on the right side of the unit. Space is provided for further pertinent data.

Model Number_______________________________________________________

Serial Number_______________________________________________________

Date of Purchase_____________________________________________________

Place of Purchase____________________________________________________

Handling Cautions

Install the cash register in a location not subject to direct sunlight, unusual temperature

changes, high humidity, or splashing water.

Do not operate the cash register with wet hands. Water can cause internal component failure.

The cash register plugs into any standard wall outlet (120V AC 10%). Avoid connecting any±

other electrical devices on the same electrical circuit since such connection could cause the

cash register to malfunction.

When cleaning the cash register, use a dry, soft cloth. Never use volatile liquids, such as

benzine or thinner. Chemicals can discolor or damage the cabinet.

For protection against data loss, please install three new batteries before using the cash“AA”

batteries; otherwise damage to memory contents or malfunctioning of the register will occur. You

can start operating it only after initializing it and then installing batteries.

For complete electrical disconnection, pull out the main plug.

Printed in Korea

O(TINSE2457BHZZ) 2

Getting Started

For Easy Set-up,

See “Getting Started”

View from rear

2. Open the battery cover next to the paper roll

cradle.

3. Insert the paper straight into the paper inlet,

and press the ff

f key. The inserted end

comes out at the printing area.

4. (For journal printing) Insert the top end of

the paper into the slit in the take-up spool

shaft and wind the paper two or three turns.

Then place the take-up spool on the bearing.

Date(March 15, 2002)

SBTL

Departments/PLU Code: The department code or

PLU code entered appears on the left. For

example, if the key for department 1 is pressed,

“ ”1 would appear in the extreme left position.

Repeat: Indicates the number of times the same

department key is pressed. If an entry is repeated

more than ten times, only the first digit is displayed

(12 displays as “ ”2).

(eeee

e) Error:

This symbol appears, accompanied by a

warning beep, when an error is made. If this

occurs during a transaction because of an

excessive digit entry, simply press

and re-enter

correctly.

(ppppp) Program: This symbol remains on the display

when the cash register is being programmed in the

Z/PGM mode.

(fffff) Finalization: This symbol appears when a

transaction is finalized by pressing or ,g k.

(oo

o) Subtotal:

This symbol appears when

SBTL

pressed and the cash register computes the

subtotal, and also when the amount tendered is

less than the total sale amount.

(cc

c) Change:

This symbol appears whenever the

change due amount is displayed.

(ll

lll) Low battery: This symbol appears when the

power of the installed batteries is below a certain

level or you need to replace the batteries with new

ones. (see the section for“Maintenance”

explanation.)

(lllll) No battery: This symbol appears when no

batteries are installed. (see “Maintenance” and

“ ”Getting Started sections for explanation.)

In addition, the following appear when appropriate:

• The minus sign (-) can appear in positions 2 to 8.

• The decimal point appears in positions 1 to 3.

•

When entry of the secret code is necessary,

“----” appears in positions 1 to 4 .

Display

The XE-A101 is equipped with a front LED (Light-

Emitting Diode) display that affords easy visibility

during transactions.

Symbols and figures appearing on the display:

REG X/F

Z/PGM

VOID

OFF

DDD In order to enter the departments 5 to 8,

press SHIFT and then the

to 4

8 keys.

transactions. Non-add code numbers can be entered

in the REG or VOID mode.

Non-add code number entry procedure:

a code number of up to 8 digits ➝ .s

Received-on-Account

and Paid-Out Entries

The received-on-account (RA) entry function is used

for entering the cash received not directly connected

with a sale. The paid-out (PO) entry function is used

for recording the money taken from the drawer for

payment not directly connected with a sale. These

functions are available in the X/F mode.

Received-on-account entry (X/F mode):

amount received (up to $799999.99) ➝ TAX1

SHIFT

/RA

Paid-out entry (X/F mode):

amount paid out (up to $799999.99) ➝

TAX2

SHIFT

/PO

Reset counter

Reset symbol

("X" is printed in the

case of X reports.)

Grand total

Quantity

Amount

Dept. code

Count of transactions

All Depts. counter and

total

Percent counter and

total

Taxable 1 total

Tax 1 total

Cash sale total

Check sale counter and

total

Charge sale counter and

total

Received-on-account total

Paid-out total

No sale counter

Sales total

Item void counter and

total

Void mode counter

and total

Cash in drawer

Clerk 1 sale total

Clerk 2 sale total

Clerk 3 sale total

Clerk 4 sale total

Tax 3 total

Taxable 2 total

Taxable 3 total

Tax 4 total

Taxable 4 total

Tax 2 total

@/TM

TAX1

SHIFT

/RA

TAX2

SHIFT

/PO

VOID

SHIFT PLU

ESC

CHK CLK#

SBTL CH

CA/AT/NS

Single Item Cash Sale (SICS) Entry

This function is used for the sale of one item to be paid

by cash. It is applicable only to departments

programmed for single-item cash sales or to PLUs

associated with such departments. After the appropriate

department or P key is pressed, the transaction is

complete and the drawer opens. For the programming of

SICS, see the Department Status section in

“ ”Programming.

PLU(Price Look Up)

The PLU function allows speedy key entries. When a

PLU code has been assigned to an item and a price for

it has been programmed, entry of the code

automatically calls up the price for the item. Up to 80

PLU codes are programmable. See the PLU

programming section in “Programming”

To enter a sale of a PLU item, simply enter its code and

press P.

Tax Calculation

Automatic Tax Calculation

When the register is programmed with a tax table or tax

rate method and the tax status of a department is

programmed as taxable, the register automatically

computes the tax on any item entered using the

department key for that department or a PLU code

associated with that department.

Taxable Subtotal

You can display the taxable 1 or taxable 2 subtotal by

pressing either tax shift key and then

SBTL

. The subtotal

of taxable 1 or taxable 2 entries is displayed. You

cannot display the subtotal of taxable 3 or 4 items.

Tax Shift

You can change the programmed taxable 1 or 2 status

of each department key by pressing one or both of the

two tax shift keys

TAX1

SHIFT

/RA

and TAX2

SHIFT

/PO . To change the taxable

status, press the appropriate tax shift key just before

the department, P or %

key. In case of repetitive

entries, the shifted tax status is used.

Tax Delete

This function is used when the taxable item or items

once entered need to be made non-taxable. Press TAX1

SHIFT

/RA

TAX2

SHIFT

/PO

, then , and and all entries made so far ins v

the transaction for items with the specified taxable

status will be made non-taxable.

Operation Examples

When Paid by Cash

1. Set the mode switch to the REG position.

2. Enter the clerk code (1 to 4) and press CLK# . (Once

the clerk code is entered, you need not enter the

clerk code at the start of each transaction until the

clerk is changed.)

3 Enter the price for the first item.

4. Press the appropriate department key.

5. Repeat steps 2 and 3 for all the remaining items.

6. Press

SBTL

to display the amount due including any

tax (you can omit this step).

7. Enter the amount received from the customer (you

can omit this step if the amount tendered is the

same as the subtotal).

8. Press , and the change due or deficit is

displayed and the drawer opens.

9. Close the drawer.

Reading and Resetting

of Sales

X Reports

This report, when taken in the X/F mode, prints the

accumulated information of sales. Taking an X

report is a good way to do a mid-day check on

daily sales. You can take X reports any number of

times, because they do not affect the cash

To issue an X report, set the mode switch to the X/F

position and press .

Z Reports

The contents of Z reports are the same as those of

X reports, but issuance of a Z report resets all the

transaction totals to zero. To issue a Z report, set

the mode switch to the Z/PGM position.

DDD If the secret code is programmed, you must

enter the secret code and press after

this step.

For Z reports without grand total resetting

Press .

D If the secret code is programmed, you have

to enter the secret code and press

again after this step.

For Z reports with grand total resetting

If you want to reset the grand total(GT)when taking

the Z report, press instead of k.

Other than resetting the grand total, this report is

the same as the normal Z reports.

DDD If the secret code is programmed, you have

to enter the secret code and press againk

after this step.

Flash Reports (displayed but not printed)

Press the following key in the X/F mode:

Department Total Department key

Sales Total #/

SBTL

Cash in Drawer CH

Display

Drawer

Drawer lock

When an Error Occurs

When your register goes into an error mode, it will

display the error symbol “ ”e accompanied with a

warning beep. Clear the error state by pressing the CL

key and take the appropriate action.

1. You enter a number of more than 7 digits for

the department price or a number larger than

the 79999999 (8 digits) for other amounts.

Press

and re-enter a correct number.

2. You make an error in key operation:

Press CL and operate keys correctly.

3. You make an entry beyond a programmed

entry digit limit:

Press CL and check if the entered amount is

correct. If not correct, re-enter a correct number. If

correct, check the setting of the entry digit limit.

4. A subtotal exceeds 79999999 (eight digits):

Press CL and then press or to finish, g k

the transaction.

5. The number of an item exceeds 3 digits in

multiplication entry:

Press

and re-enter the correct number.

Error Escape Function

When an error or something uncontrollable occurs

during a transaction entry and you cannot keep the

customer waiting, press ESC twice (following

when

in the error state). You can escape the situation and

finalize the transaction as a cash sale at that time.

Transaction entries to that point are registered.

Clerk code

CLK#

Price and dept.Price and dept.

Amount tendered

SBTL

@/TM @/TM

3 3

SBTL

CHK

When Paid by a Credit Card

Press

at the end of the transaction. The amount

tendered cannot be entered.

When Paid by Check

Press CHK at the end of the transaction. The amount

tendered can be entered like a cash sale and the

change due is displayed.

Mixed Tender Sale

When the amount tendered by cash or check is less

than the sales amount including tax, the display shows

a deficit and . To compensate for the deficit, make“ ”o

an additional amount-tendered entry or make a charge

entry.

Department

Repetitive Department Entries

To enter two or more of the same item, press the

appropriate department key repeatedly.

Multiplication Entries

To enter a sale of two or more of the same item, use

@/TM

key for multiplication.

Example:

Selling five pieces of $1.50 item (department 1)

and three pieces of $3.50 item (department 3)

for check payment.

Keyboard

Printer cover

Mode switch

87654321

PLU code

Repeat

Department code

X/Z Report Sample

To make all entries up to that point non-taxable, press

TAX1

SHIFT

/RA

and

TAX2

SHIFT

/PO

, then

SBTL

, and

Subsequent entries in the

transaction remain unaffected and will be taxed normally.

Manual Tax

You can apply tax manually when the automatic tax

calculation function cannot be used. Each manual tax

entry (for Tax 1 or Tax 2) can be made only once during

a transaction. After a manual tax entry, you cannot

make any further item entries.

Manual tax 1 entry:

TAX1

SHIFT

/RA and

SBTL

➝ tax amount ➝

SBTL

Manual tax 2 entry:

TAX2

SHIFT

/PO

and #/

SBTL ➝ tax amount ➝#/

SBTL

Opening the Drawer

with No Sale

Just press and the drawer opens.

Percent Key

The percent key is used to apply a discount or premium

to an item or to a subtotal.

You can manually enter a discount (or premium) rate.

Once the rate is preset for

, you can skip the step of

entering the rate.

Discount for an item:

entry of an item percentage rate ➝ ➝ %

(ex. For 20%, enter

Discount for a subtotal:

entry of all items➝

SBTL

➝ percentage rate ➝ %

(ex. For 5%, enter

Entering a Refund

The cash register has no refund key. You must use the

following alternative method to make a refund entry: A

negative department for refund must be programmed in

advance. Check the taxable status of the returned item

is the same as that of the programmed negative

department. If not, use the appropriate tax shift key to

change the taxable status.

Procedure

unit price of the returned item negative dept. key➝

➝ or g.

Non-add Code Number

Non-add code numbers can be entered and printed on

the journal (or receipt) during the entry of a sale. Non-

add codes can be used for credit numbers, check

numbers, serial numbers, product codes, service charge

codes or any other numbers for reference to

specific

Part Names and Functions

Mode Switch

The mode switch enables the register to perform a

variety of functions. Mode switch settings are

made by sliding the switch .

You can select the following functions:

REG: Permits transaction entries.

OFF: Turns the display off.

VOID: Permits you to cancel transaction entries.

X/F: Permits printing of sales reports and

displaying of flash reports.

Z/PGM: Permits printing of sales reports, resetting

of sales data and programming.

Keyboard Layout

Entries

PLU code Price Associated dept.

SBTL

PLU code ➝ ➝ P Price Dept. key➝

( ➝

SBTL )

Ex.:

To disable a PLU code, use the following sequence:

PLU code ➝ ➝ P➝ v ( #/

SBTL )

Before you begin programming, set the mode switch to

the Z/PGM position.

B, C, D and E: Choice of taxable status

Enter 0000 for non-taxable, 0001 for taxable 1,

0010 for taxable 2, 0100 for taxable 3, 1000 for

taxable 4 or 0011 for taxable 1 and 2.

Initial setting: - (discount), non-taxable ("10000")

Programming the percent rate

Use the following sequence:

Percent rate (0.01% to 99.99%) ➝ ➝ % ( #/

SBTL )

(ex. For 10.00% enter

Initial setting: 0.00(%)

Printing Format

You can choose either a journal or receipt format and

specify other options for the printing format. Use the

following sequence:

➝#/

SBTL ➝ ABCDEFG ➝ #/

SBTL (➝

SBTL

)

A: Printing journal/receipt in the REG mode

Enter 0 for printing or 1 for no printing.

B: Journal or receipt format

Enter 0 for journal format or 1 for receipt format.

(In the receipt format, the paper is fed by a few

lines upon finalization of each transaction. In the

journal format, the paper is wound around the take-

up spool.)

C: Printing date