Seco-Larm Enforcer EV-Y6201-A3WQ Bedienungsanleitung

Seco-Larm Sicherheitskamera Enforcer EV-Y6201-A3WQ

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Seco-Larm Enforcer EV-Y6201-A3WQ (4 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war fĂĽr 31 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
EV- - Y6201 A3WQ
4- - in 1 HD TVI, CVI, AHD, Analog
UFO Camera
Manual
• Select between multiple formats:
TVI, CVI, AHD, and Analog
•
1080p Resolution
•
3.7mm Pinhole lens rotates to nearly any
angle for flexible installations
•
3D- NR (3D Digital Noise Reduction)
•
DWDR (Digital Wide Dynamic Range)
• Low 0.1Lux rating
•
1/2.9" 2MP Sony CMOS
•
Heavy- - duty vandal resistant design
•
Rugged, weatherproof (IP66) construction
•
Small size protrudes only 1" (26mm)
•
Low- profile design blends in with nearly
any decor
Features:
ENFORCER 4- - in 1 HD TVI, CVI, AHD, Analog UFO Camera
2 - SECO LARM U.S.A., Inc.
Specifications:
Type
Flush-Mount UFO Camera
Formats
TVI (Default) / CVI / AHD / Analog
CMOS
1
/2.9" 2MP Sony CMOS
Resolution (HD)
1920x1080
TV Lines (Analog)
1200TVL
2D-NR
Yes
3D-NR
Yes
DWDR
Yes
OSD (On- Screen Display)
Yes
Cable OSD control
Yes
Video output
1.0Vp-p Complex video output
Megapixels
2MP
Lens
3.7mm Pinhole lens
Viewing angle
80°
FPS
30FPS
F Stop
F1.4
Minimum illumination
0.1Lux
Gamma correction
0-1
S/N Ratio
50dB
DSS (Digital Show Shutter)
Yes
Shutter control
Auto/Manual (x30~1/50000), FLK
Gain control
Yes
White balance
Auto, Day & Night
Operating voltage
12VDC
Current draw
90mA
IP Rating
IP66
Operating temperature
-4 - °~131° F ( 20°~55° C)
Dimensions
3"x3"x1" (77x77x26 mm) (Protruding from wall)
Weight
9.9-oz (280g)
Parts List:
Dimensions:
1x
1x
Base
3x
Mounting screws
1x
1x
Ring bracket
1 x
DC Plug with terminal block
1x
Flange
Camera ball
Base
Assembled camera
3"
(77mm)
115 /
16
"
(49mm)
213 /
16
"
(72mm)
21/
4
"
(56mm)
1"
(26mm)
3" (77mm)
ENFORCER 4- - in 1 HD TVI, CVI, AHD, Analog UFO Camera
SECO- LARM U.S.A., Inc. 3
Overview:
Before Starting:
Installation:
Important: Do not cut any wires as the warranty will be voided.
1. Use the camera within the given temperature
and voltage limits.
2. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
3. Do not subject the camera to strong vibrations.
4. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
1. Run a 12VDC power supply wire and a video
cable with a male BNC connector to the wall or
ceiling where the camera is to be mounted.
2. Temporarily connect the camera to the 12VDC
power supply.
3. Temporarily connect the camera’s female BNC
connector to the video cable’s male BNC
connector.
4. While watching the monitor, hold the camera
against the wall or ceiling by hand where it is to be
mounted, then turn the camera until it is certain
that this ounting location is correct. Use a pencil m
to mark the location.
5. Disconnect the power supply and video cable.
6. Cut or drill a 21/16” (52m ) hole in the ceiling or m
wall where the camera is to be mounted.
7. Twist the flange off the base and remove the
camera ball.
8. Place the ring bracket behind the hole.
NOTE: Ring bracket is not necessary if
surface mounted.-
9. Push the base into the hole, and secure to the ring
bracket using the three supplied mounting screws.
10. Run the power supply and video cable through the
wall or ceiling to the hole, and through the bracket
and base. Connect to the camera’s power and
video connectors.
11. Hold the ball in the base, and secure with the
flange. Secure the flange partially, leaving room to
adjust the angle of the lens.
12. Use the OSD controller's joystick to adjust camera
settings (see the separate OSD manual).
13. Apply the power to the camera. Watch the monitor
and adjust the angle of the lens.
14. Secure the camera by tightening the flange.
15. Do a final test of the video camera and monitor.
Surface nstallation-Mount I :
Requires the EV- s6640SWQ (Sold eparately)
Standard Installation:
Surface-mount
bracket
Run the power and
video cables through
the wall or on surface
OSD Controller Settings:
To set format via the OSD controller, press the
controller in the direction of the desired setting,
hold for 5 seconds, and rel
ease when the
camera restarts.
See chart below.
For the full
OSD manual : visit
www.
SECO-LARM.com.
Direction
Format Setting
Up
CVI
Down
TVI
Left
CVBS
Right
AHD
DC Plug with
terminal block
Flange
Camera
Ball
Mounting
screws x3
Ring bracket
( inside ceiling/wall)
Base
OSD controller
DC Jack
Female BNC
Connector
Wall
or
Ceiling
Wall
or
Ceiling
UP
DN
P ower
Camera

Produktspezifikationen

Marke: Seco-Larm
Kategorie: Sicherheitskamera
Modell: Enforcer EV-Y6201-A3WQ

Brauchst du Hilfe?

Wenn Sie Hilfe mit Seco-Larm Enforcer EV-Y6201-A3WQ benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Sicherheitskamera Seco-Larm

Seco-Larm

Seco-Larm Enforcer EV-Y6201-A3WQ Bedienungsanleitung

23 März 2024
Seco-Larm

Seco-Larm Enforcer EV-Y2201-A2WQ Bedienungsanleitung

6 März 2024

Bedienungsanleitung Sicherheitskamera

Neueste Bedienungsanleitung fĂĽr -Kategorien-

Speco Technologies

Speco Technologies O2PTZ34D5W Bedienungsanleitung

14 August 2024
ZKTeco

ZKTeco BL-34F26L Bedienungsanleitung

11 August 2024
Moxa

Moxa VPort 26 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 36 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-M12-CAM3L54160N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort P06 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPORT P06-1MP-M12-CAM80 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-DO-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 26A-1MP Bedienungsanleitung

27 Juni 2024