SE Electronics V Clamp Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für SE Electronics V Clamp (16 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/16
V KICK V BE AT V CLAM P
U s e r M a n u a l
2
User Manual - EN
Thank you
We would like to thank you cordially for choosing this sE product! This manual contains some
important instructions for setting up and operating your new equipment. Please take a few minutes
to read the instructions below carefully. We hope you will enjoy working with it as much as we
enjoyed designing and building it for you.
Most Sincerely,
Your sE Team
Brief Descriptions
V KICK
The V KICK is a dynamic microphone intended for use with kick (bass) drums and other sources
such as miking bass guitar speaker cabinets, floor toms or other large drums where capturing low-
frequency energy is of the utmost importance. Its specialized capsule provides a sound character
tailored specifically for kick drums, which can be further shaped with the use of two switches on the
rear side of the microphone.
V BEAT
The V BEAT is a dynamic microphone intended for use with snare or tom drums, but it can also be
used on sources such as miking electric guitar speaker cabinets or brass instruments. Its
specialized capsule provides a highly detailed, natural sound character on snares or toms of any
size.
V CLAMP
The V CLAMP was designed to be the perfect companion for the V BEAT for snare or tom miking
purposes. Its sturdy elastic clamp enables setup and tear-down within seconds, and it fits any
popular snare or tom drum available.
Product Details
V KICK
The V KICK’s specialized capsule provides a sound character tailored
specifically for kick drums, which can be further shaped with the use of
two switches on the rear side of the microphone.
The left-hand switch shapes the microphone’s overall voicing, with two
selectable options:
“Classic” provides a more traditional kick drum sound with a familiar
low frequency punch and a warmer, more rounded sound. If a more
contemporary, aggressive sound is desired, the setting “Modern
emphasizes the low end and high end (a scooped” sound).
3
The right-hand switch specifically tailors the microphone’s high-frequency character:
“Classic” provides a typical bite in the upper midrange (presence boost) and a more rounded and
familiar sound, while provides an open, clear and transient-rich top end for a more HF “Modern”
contemporary, aggressive drum sound.
Each of these switches is recessed slightly into the mic body and requires a small flathead
screwdriver or similar implement to switch between settings.
The V KICK also has an integrated swivel joint that allows for easy
positioning inside or outside a kick drum. I extremely low profile allows ts
it to fit easily through the drum head port, and the XLR cable and mic
stand mount are in parallel to minimize cable clutter. Please remember
to securely tighten the swivel clamp whenever adjusting it, so as to
prevent the mic from sagging during a performance or recording.
V BEAT
The V BEAT’s ultra-compact design lets it occupy a minimal amount of space on your drum, without
interrupting lines of sight any more than necessary, and keeping it out of the way of drum sticks and
cymbals. With the XLR connector and stand mount on the bottom of the V BEAT and in parallel with
one another, the footprint and cable clutter are further minimized.
Its swivel mount also allows the
angle of the mic to be adjusted with
great precision, so it can be aimed at
almost any part of the drum head to
change the character of the sound,
and to minimize spill from other
drums or cymbals.
Please remember to securely tighten the swivel clamp whenever adjusting it, so as to prevent the
mic from sagging during a performance or recording.
V CLAMP
The V CLAM can be fitted to any popular snare or tom drum available P
by carefully stretching the elastic clamp over the drum rims to fit The .
height and rotation of the connected microphone can be changed by
loosening the V CLAMP’s knob and adjusting the position of the rod. This
allows the mic to be positioned perfectly for any desired drum tone, or to
minimize spill from nearby drums. The small hole at the bottom of the
rod can be used for a tie clip to attach a cable, or as a backup solution in
case the knob becomes loose for any reason.


Produktspezifikationen

Marke: SE Electronics
Kategorie: Nicht kategorisiert
Modell: V Clamp

Brauchst du Hilfe?

Wenn Sie Hilfe mit SE Electronics V Clamp benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert SE Electronics

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-