Scosche TA2047B Bedienungsanleitung

Scosche Kfz-Bausatz TA2047B

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Scosche TA2047B (4 Seiten) in der Kategorie Kfz-Bausatz. Dieser Bedienungsanleitung war fĂĽr 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
1
142TA2047B
IN-DASH INSTALLATION KIT FOR
2001-UP TOYOTA RAV4 /
2000-UP MR2 SPYDER
1987-UP TOYOTA VEHICLES
Rear Speaker Plug
1 = Right Rear Negative
2 = Left Rear Negative
3 = Right Rear Positive
4 = Empty
5 = Empty
6 = Left Rear
Positive
CAR STEREO CONNECTOR
PROVIDE EASY CONNECTION
OF YOUR CAR STEREO
TO FACTORY WIRING
HARNESS.
TA02
1987-up Toyota
©2001 SCOSCHE INDUSTRIES, INC. SI 9/01-142TA2047B (3000005)
If you have any further questions, call TECH HELP 1-800-621-3695, ext. 3
142TA2047B
RAV4
MOUNTING
BRACKET
142TA2047B
POCKET
142TA2047B
TRIM RING
142TA2047B
MOUNTING
PANEL
Front Speaker and PowePlug
1 = Right Front Negative
2 = Left Front Negative
3 = Accessory +12V
4 = +12V Constant, Battery
5 = Right Front Positive
6 = Left Front Positive
7 = Chassis Ground
8 = Empty
9 = Empty
10 = Illumination +12V
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/codes and
information pertaining to installation of this kit (142TA2047B) in 2001-UP Toyota RAV4 / 2000-UP MR2 Spyder vehicles. Scosche
Industries, Inc. can not be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing
changes or options, or damage that may occur in the automobile during the installation of components while using this booklet.
2
DIN RADIO INSTALLATION (DETACHABLE FACE/PULLOUT)
Slide the mounting sleeve (metal shroud) into the panel’s radio opening and bend all available mounting
tabs outward (see inset). Once the radio mounting sleeve has been fastened to the kit panel, slide the
radio into the mounting sleeve until it locks into place.
NOTE: The mounting sleeve must be removed from the radio first!
Your radio may be snapped into its sleeve. Slide the mounting
sleeve (metal shroud) off the radio towards the back.
INTRODUCTION
This premium installation kit is for 2000-Up Toyota MR2 Spyder and 2001-Up RAV4 vehicles. Included
are all of the parts you need to mount your car stereo/cassette or CD player into your vehicle’s dash.
Refer to the individual instruction in this manual to remove your vehicle’s factory radio and assemble the
kit.
CAUTION: Disconnect your vehicle's negative battery terminal before the installation to help
prevent electrical damage. We recommend the use of a volt/ohm meter over a test light to
check wiring. A test light or grounded wire probe can cause damage to the vehicle's
computer and/or diagnostic systems. Avoid all factory air bag wiring - air bags can
accidentally deploy causing serious injury or death.
NOTES:
• See your vehicle’s instructions for any special tools your installation requires.
• Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting
instructions.
CAUTION:
REAR SUPPORTING THE
RADIO ADDS TO THE
INSTALLATION’S
STRUCTURAL INTEGRITY.
DIN RADIO
REAR SUPPORT
STRAP
142TA2047B
MOUNTING
PANE
RADIO
MOUNTING
SLEEVE
142TA2047B
TRIM RING
BEND
TABS
OUTWARD
RAV4 BRACKET ASSEMBLY
BACK VIEW OF
MOUNTING
PANEL
BACK VIEW
OF POCKET
RAV4 BRACKET INSTALLATION
1. The bracket is only used for
installation in Toyota RAV4.
2. Align the snaps of RAV4 mounting
bracket with the pocket slots.
3. When aligned, snap bracket
carefully into position until locked.
CAUTION:
REAR SUPPORTING THE
RADIO ADDS TO THE
INSTALLATION’S
STRUCTURAL INTEGRITY.
2000-UP TOYOTA MR2 SPYDER
RADIO REMOVAL AND IN-DASH INSTALLATION:
Note: The factory radio provision is for a Double ISO/DIN style radio.
1. Use panel removal tool to remove left and right plastic side panels, extract (1) Phillips screw from
behind each panel.
2. Remove climate control knobs, and extract (2) Phillips screws.
3. Remove radio trim bezel.
4. Remove ash tray and extract (1) 10mm bolt on the right side, carefully pry out ash tray trim bezel,
disconnect and remove.
5. Extract (4) Phillips screws securing radio, disconnect and remove from dash.
USE THE SHADED MOUNTING TABS. CUT OFF THE REMAINING TABS AND DISCARD.
CAUTION:
REAR SUPPORTING THE
RADIO ADDS TO THE
INSTALLATION’S
STRUCTURAL INTEGRITY.
USE
THESE
TABS
USE
THESE
TABS
3

Produktspezifikationen

Marke: Scosche
Kategorie: Kfz-Bausatz
Modell: TA2047B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Scosche TA2047B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Kfz-Bausatz Scosche

Scosche

Scosche BTFreq Pro Bedienungsanleitung

5 September 2024
Scosche

Scosche KA2091B Bedienungsanleitung

22 August 2024
Scosche

Scosche auxMIC Bedienungsanleitung

21 August 2024
Scosche

Scosche NN1640B Bedienungsanleitung

21 August 2024
Scosche

Scosche TA2074B Bedienungsanleitung

21 August 2024
Scosche

Scosche TA2077B Bedienungsanleitung

21 August 2024
Scosche

Scosche TA2079B Bedienungsanleitung

21 August 2024
Scosche

Scosche NN1648B Bedienungsanleitung

21 August 2024
Scosche

Scosche SI2229B Bedienungsanleitung

21 August 2024
Scosche

Scosche VO4152B Bedienungsanleitung

21 August 2024

Bedienungsanleitung Kfz-Bausatz

Neueste Bedienungsanleitung fĂĽr -Kategorien-

Parrot

Parrot Minikit Chic Bedienungsanleitung

29 September 2024
Nedis

Nedis DTCTCO20WT Bedienungsanleitung

22 September 2024
BURY

BURY UNI Bedienungsanleitung

21 September 2024
Gembird

Gembird Bluetooth Car Kit BTCC-002 Bedienungsanleitung

19 September 2024
BURY

BURY Easytouch Pro Bedienungsanleitung

18 September 2024
Alpine

Alpine HCE-C157D Bedienungsanleitung

18 September 2024
Pyle

Pyle PL91HRTN Bedienungsanleitung

17 September 2024
BURY

BURY CV 9040 Bedienungsanleitung

14 September 2024
Alpine

Alpine KCE-425i Bedienungsanleitung

14 September 2024
Alpin

Alpin 61431 Bedienungsanleitung

9 September 2024