Scosche SI2227TB Bedienungsanleitung

Scosche Kfz-Bausatz SI2227TB

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Scosche SI2227TB (1 Seiten) in der Kategorie Kfz-Bausatz. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
© 2007 SCOSCHE INDUSTRIES, INC. SI -07/07 - SI2227TB (3000003)
If you have any further questions, call our toll free technical help line at: 1-800-621-3695x3
SI2227TB
IN-DASH INSTALLATION KIT FOR
2006-UP SUZUKI GRAND VITARA
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire
harness/codes and information pertaining to installation of this kit (SI2227TB) in 2006-UP Suzuki Grand Vitara
Vehicles. Scosche Industries, Inc. can not be held responsible for discrepancies/inconsistencies that may occur due
to the automobile manufacturing changes or options, or damage that may occur in the automobile during the
installation of components while using this booklet.
Thank you for purchasing the Scosche SI2227TB Kit. This kit was manufactured with the highest of
quality standards.
CAUTION:
DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLA-
TION TO HELP PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/
OHM METER OVER A TEST LIGHT TO CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE
PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S COMPUTER AND/OR DIAGNOSTIC
SYSTEMS. AVOID ALL FACTORY AIR BAG WIRING - AIR BAGS CAN ACCIDENTALLY DEPLOY
CAUSING SERIOUS INJURY OR DEATH.
NOTES:
•See your vehicle's instructions for any special tools your installation might require.
•Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting
instructions.
INTRODUCTION / PRELIMINARY
FACTORY WIRING CODES
CAR STEREO CONNECTORS
PROVIDE EASY CONNECTION OF YOUR CAR
STEREO TO FACTORY WIRING HARNESS.
SI03B
1996-UP Suzuki Harness
SI03B
6193 KIT PANEL
6194
POCKET
POCKET ASSEMBLY
ATTACHING THE TRIM RING:
Press the pocket into the lower position of the mount opening.
There are (4) hole mounting locations to mount. Use
supplied screws from installation kit.
MOUNTING THE RADIO
MOUNTING THE RADIO FOR SINGLE DIN OR DOUBLE DIN:
A. Mount the aftermarket DIN radio to the factory metal
mounting brackets using top holes with the factory
hardware.
B. For Double din aftermarket radio align factory brackets to
double din holes, two top hole and one bottom hole should
be usable. Align radio mounting assembly to the kit panel
trim ring.
C. Secure the whole panel assembly to the dash using
screws used to secure the factory radio.
NOTE:
REAR SUPPORT AVAILABLE
SEPARATELY. REAR
SUPPORTING THE RADIO
ADDS TO THE INSTALLATION’S
STRUCTURAL INTEGRITY.
2
STEREO INSTALLATION
1. Using a panel removal tool, remove the trim on both sides of radio and A/C control. This piece
extends from side of shifter up to side of AC vents above stereo.
2. Remove the (6) Phillips Screws holding the radio and climate control. Disconnect and remove.
3. Remove (3) screws on each side of radio.
4. Remove (2) Phillips Screws holding A/C control to radio.
ASSEMBLED
6193 PANEL
6193 PANEL
FACTORY
METAL
BRACKET
6194 POCKET
6193
KIT
PANEL


Produktspezifikationen

Marke: Scosche
Kategorie: Kfz-Bausatz
Modell: SI2227TB

Brauchst du Hilfe?

Wenn Sie Hilfe mit Scosche SI2227TB benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Kfz-Bausatz Scosche

Bedienungsanleitung Kfz-Bausatz

Neueste Bedienungsanleitung für -Kategorien-