Sani-Lav 5A4F Bedienungsanleitung
Sani-Lav
Waschbecken
5A4F
Lesen Sie kostenlos die π deutsche Bedienungsanleitung fΓΌr Sani-Lav 5A4F (5 Seiten) in der Kategorie Waschbecken. Dieser Bedienungsanleitung war fΓΌr 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/5
1
W A L L M O U N T S I N K
Operating Manual for Wall Mount Stainless Steel Sink
Models 5A4F and 5A4F-0.5
of Domestic and Foreign Parts
Columbia does not recommend use with harsh chemicals.
Product Compliance
NSF/ANSI 2 Food Equipment, NSF/ANSI 61, Section 9, ASME A112.18.1/CSA B125.1, ADA Compliant
ADA Compliant
Illustration A
Illustration B
Illustration C
2
C O L U M B I A S P E C I F I C AT I O N S
800.626.2117 columbiasinks.com info@columbiasinks.com
Β©2021 Columbia Products
W A L L M O U N T S I N K
Installation Instructions
Step 1
1. Establish sink location on the wall.
2. Measure a recommended 45β from finished floor and draw a level line which will be the top edge
of the wall mounting bracket.
3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill holes
and secure bracket to the wall as shown in illustration A. Screws are not provided.
Step 2
1. Install faucet to the sink using faucet mounting kit provided. We recommend using pipe thread
sealant instead of Teflon tape.
2. Install strainer assembly to the drain hole.
3. Connect hot and cold water supply lines (not included) to the back of faucets.
Step 3
1. Position sink onto the wall bracket.
2. Mount support bracket to the bottom of the sink. Do not tighten.
3. Slide or push support brackets against the wall and mark holes for fastening. See illustration B.
4. Remove support brackets from the sink and drill holes for fastening.
5. Install fastening hardware to the drilled holes. (not included)
6. Mount support bracket to the bottom of the sink and fasten them to the wall.
Step 4
1. Install valves onto the sink.
2. Install elbow fittings to Knee Pedal Valves.
3. Connect hot and cold connecting tubes from the spouts to valves.
Step 5
1. Connect waste line or drain pipe to the strainer assembly.
2. Connect hot and cold water supply line to the water source.
Step 6
1. Remove aerator from the spout assembly and flush water system. Check connections for leaks.
Replace aerator onto the spout assembly.
2. We recommend sealing top of backsplash to wall as shown in illustration C.
Parts List
(1) Wall mount sink
(1) 8β on center faucet
(1) Faucet mounting kit
(1) Wall-mounting bracket
(2) Support brackets
(4) Support bracket mounting bolts and washers
(1) Strainer assembly with basket
Trouble Shooting Guide
Problem Possible Cause To Diagnose Remedy
Water drips from
the spout or from
under the lever.
1. Seat washer is worn
2. Seat is worn
3. O-rings are worn
Shut cold water source off.
See if water still leaks from the
spout. If leaks continues repair
hot side if not repair cold side.
Recommend
installing hot
or cold faucet
repair kit.
Tools Required
Tape measure
Adjustable wrench
Drill motor and drill bits
Pipe wrench
Level
Safety glasses
Screw drivers: phillips and standard
Pencil
Socket wrench
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certiξed under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Go to for more information on replacement parts and installation videos.columbiasinks.com
Wall-mounting bracket
9β (228.6mm)
Front
21β (533.4mm)
7.5β
(191mm)
.875β (22mm)
dia. holes (2)
Hole Conο¬gurations
6β (152.4mm)
14β
(355.6mm)
14β
(355.6mm)
8β
(203.2mm)
5β (127mm)
4β (101.6mm)
2β (50.8mm)
.5β R (12.7mm)
22β (558.8mm)
11β
(279.4mm) 11β
(279.4mm)
19β
(482.6mm)
15.5β
(381mm)
1.5β (38mm)
2β (51mm)
Top
19β (482.6mm)
6β (152.4 mm)
1.5β (38mm)
.5β R
(12.7mm) Cross-breaks
to aid drainage
2β drain hole
9β (228.6mm)
45ΒΊ
7β (177.8mm)
35β (889mm)
suggested
ο¬oor to rim
height
Side 19β (482.6mm)
2β (51mm)
1.5β (38mm)
16.75β
(425.5mm)
1.5β
(38.1mm) .875β
(22.22mm)
Back
Splash
.25β
dia. hole
Wall Mounting Detail
Supply Line Detail
Back Splash
1/2β Male NPT
Hot
from Wall
Cold
from Wall
3
C O L U M B I A S P E C I F I C AT I O N S
800.626.2117 columbiasinks.com info@columbiasinks.com
Β©2021 Columbia Products
W A L L M O U N T S I N K
Produktspezifikationen
| Marke: | Sani-Lav |
| Kategorie: | Waschbecken |
| Modell: | 5A4F |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Sani-Lav 5A4F benΓΆtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Waschbecken Sani-Lav
22 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
Bedienungsanleitung Waschbecken
- Waschbecken Concept
- Waschbecken Teka
- Waschbecken IKEA
- Waschbecken Smeg
- Waschbecken Hotpoint-Ariston
- Waschbecken Bartscher
- Waschbecken Lynx
- Waschbecken Caple
- Waschbecken Kernau
- Waschbecken Franke
- Waschbecken Foster
- Waschbecken Cata
- Waschbecken Leisure
- Waschbecken Nodor
- Waschbecken Miomare
- Waschbecken Gustavsberg
- Waschbecken CDA
- Waschbecken Schock
- Waschbecken Rangemaster
- Waschbecken BLANCO
- Waschbecken Elkay
- Waschbecken Deante
- Waschbecken ZLine
- Waschbecken Roca
- Waschbecken Artusi
- Waschbecken Advance Tabco
- Waschbecken ARC
- Waschbecken Rohl
- Waschbecken Differnz
- Waschbecken Coyote
- Waschbecken Tot Mate
- Waschbecken Kuchinox
- Waschbecken Oliveri
- Waschbecken Enza
- Waschbecken Laveo
- Waschbecken Shaws
- Waschbecken Dxv
- Waschbecken Vigo
- Waschbecken Signature Hardware
Neueste Bedienungsanleitung fΓΌr -Kategorien-
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
12 Oktober 2024
11 Oktober 2024
11 Oktober 2024