Rolls RM67 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Rolls RM67 (2 Seiten) in der Kategorie Mischpult. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
RM67
Mic/Source Mixer
Quick Start Guide
ROLLS CORPORATION
SALT LAKE CITY, UTAH
05/13
FEATURES
- Three XLR balanced inputs with phantom power
- Four stereo Source inputs, including a resistor-mixed front panel 3.5mm input
- Tone controls for each Microphone input
- Clip indicators for each Microphone input
- Bass and Treble controls for the Source inputs
- 1/4” input for remote volume control
- RCA Record Out
- Master Output Level control
- 1/4” TRS balanced outputs
- Ducking with adjustable Sensitivity control
SPECIFICATIONS
Input Impedance: Mic: 600 Ohms XLR balanced
Line: 22K Ohms
Source:
22K
Ohms
gold plated RCA
Mic Insert: 22K Ohms 1/4” TS unbal.
Max Input Level: Mic: -14 dBV Mic level
+20 dB Line levl
Source: 24 dBV
Connectors: 3: XLR, 6: Stereo RCA, 3: 1/4” TRS, 1: 1/4 TS, 1: 3.5mm
Phantom Power: +12 VDC
Output Level: +17 dBV max
Output Impedance: 51 Ohms
Max Gain: Mic: 60 dB
Source: 26 dB
Tone Controls: +/-12 dB 100 Hz Bass
+/-12 dB 11kHz Treble
Nose Floor: - 80 dB, THD: <.025%, S/N Ratio: 96 dB
Size: 19” x 1.75” x 6” (48.3 x 4.5 x 15 cm)
Weight: 5 lbs. (2.3 kg)
SCHEMATIC
N O T E : T H I S G U I D E A S S U M E S T H E U S E R H A S A W O R K I N G
K N O W L E D G E O F A U D I O E L E C T R O N I C S , B A L A N C E D A N D
UNBALANCED CONNECTIONS, AND PROPER SIGNAL LEVEL SETTING.
SOURCE 1
INTRODUCTION
Thank your for your purchase of the Rolls RM67 Microphone/Source Mixer. The RM67 is a single
rack space audio mixer with three XLR inputs and four stereo RCA source inputs. Talkover fea-
tures have been included on Mic 1 and Source 4 for paging and music priority functions.
INSPECTION
1. Unpack and inspect the RM67 box and package.
If obvious physical damage is noticed, contact the carrier immediately to make a damage claim.
2. For warranty information, and to register your warranty, please visit our website at www.rolls.
com and click on the Register Your Warranty Here button.
DESCRIPTION
FRONT PANEL
Mic 1 - 3: Adjust the level of signal from the corresponding Mic Input.
clip 1 - 3: LED indicating overload in the channel. The LED lights 3dB below clipping.
TONE 1 - 3: Adjusts the frequency content of the signal in the channel. When the control is
turned counter-clockwise, the high frequencies are cut, when the control is turned clockwise,
the low frequencies are cut.
IN 1: 3.5mm Input jack - resistor mixed to Source Input 1.
Source 1 - 4: Adjust the volume of input from the RCA Source Inputs, and the 3.5mm in.
Bass: Adjusts the low frequencies of the Source signals only.
Treble: Adjusts the high frequencies of the Source signals only.
Master Level: Adjusts the overall volume of the RM67 Main Outputs.
pwr: LED indicating power is applied to the RM67 and the unit is on.
REAR PANEL
Mic 1 - 3: XLR inputs for dynamic or condenser microphones, or balanced line-level signals.
Mic/Line Switch: Pads the XLR Mic input by 30 dB when pressed in.
DIP SWITCH: Contains the small switches for engaging Mic 1 - 3 phantom power, the priority
(Talk Over) functions, and the Mono/Stereo select.
MIC INSERT: 1/4 TRS insert jack for adding external processing to the Mic signals. Tip = send, ring
= return.
SOURCE INPUTS: Stereo RCA jacks, Channels 1 - 4, for connection to stereo sources such as AM/
FM tuners, cassette players, cd players, or video players.
RECORD OUT: Stereo RCA jacks, contains all mixed signals before the Remote Volume jack, and
Master Level control.
SPARE: This RCA jack is not connected.
MUTE: RCA jack for connection to a tip-to-ground muting circuit.
REMOTE VOLUME: 1/4” TS jack for connection to a remote potentiometer for master volume
control. 20K Ohm audio taper potentiometer is recommended.
MAIN OUTPUTS: 1/4” TRS balanced Right and Left Outputs.
DUCK SENSITIVITY: Adjusts the level of input signal required for ducking to occur. NOTE: The
release time is e ected by this setting, plus the level of input signal - the higher the input signal,
the longer the release time.
IEC POWER INPUT: Connect to the IEC power cable - and properly grounded ac outlet.
CONNECTION
Connect low impedance microphones to the Mic inputs. If a paging microphone is being used,
connect it to Mic Input 1 so it may be used with the Talk Over function. Connect source signals
such as CD players, cassette players or video players to the RCA Source Inputs. If a jukebox is
being connected, and you want its signal to mute the other source signals, connect it to Source
input 4. Connect 3.5mm sources to the front panel input.
Remote Volume Control
To control the overall volume of the RM67 in a remote location, wire a
100K ohm Linear Taper potentiometer to a 1/4” Tip-Ring-Sleeve plug
as shown here.
Mic Insert
To connect a signal processor to the RM67 micro-
phone signal(s), use an insert plug, or cable wired
as shown here.
Connect the Main Right and Left outputs to your
power ampli ers. The RM67 output jacks will ac-
commodate balanced or unbalanced connections. For unbalanced operation use 1/4” Tip Sleeve
jacks, for balanced operation use 1/4 Tip Ring Sleeve jacks. If a 1/4” TRS to XLR cable is needed,
wire the Tip of the 1/4” jack to pin 2 of the XLR, the Ring to pin 3, and the Sleeve to pin 1 or the
shield.
Mute
To mute all audio, connect an RCA plug to your muting circuitry. When the tip is shorted to the
ground - all audio is muted.
Connect the RM67 to a properly grounded AC outlet.
DIP SWITCH SETTINGS
- If a microphone requires phantom power, move the Mic channel’s corresponding PHAN DIP
switch to the down position. This applies 12 volts dc phantom power to the indicated micro-
phone.
- Talkover switch 1 (T.O. 1), when in the down position, all program material on all source inputs
will be ducked” or muted when a signal is present at Mic 1. NOTE: MIC ONE WILL NOT TALK OVER
MIC2 OR MIC3. ONLY THE SOURCE INPUTS WILL BE TALKED OVER. This function is used for pag-
ing.
- Talkover switch 2 (T.O. 2), when in the down position, Source 1,2, and 3 will be ducked” or
muted by the signals at Source 4.
This function is for jukebox priority. With a jukebox connected to Source input 4, and the
Talkover switch 2 on (down), the other Source input signals such as background music, will be
muted and only the jukebox will be heard.
- The Mono/Stereo switch selects the output mode. When the switch is up, the unit is in stereo
mode. When the switch is down, the stereo signals are mixed to mono and sent to both the
Right and Left Main output jacks. Either jack can be used as a mono output.
Adjust the Microphone levels for maximum input signal without clipping, and for a comfortable
listening level. Adjust each Source level for a desired listening level.
To Mic Insert


Produktspezifikationen

Marke: Rolls
Kategorie: Mischpult
Modell: RM67

Brauchst du Hilfe?

Wenn Sie Hilfe mit Rolls RM67 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Mischpult Rolls

Bedienungsanleitung Mischpult

Neueste Bedienungsanleitung für -Kategorien-