Roland XC-540 Bedienungsanleitung

Roland Drucker XC-540

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Roland XC-540 (156 Seiten) in der Kategorie Drucker. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/156

USER'S MANUAL

Thank you very much for purchasing this product.

➢To ensure correct and safe usage with a full understanding of this product's performance, please be

sure to read through this manual completely and store it in a safe location.

➢Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.

➢The contents of this operation manual and the specifications of this product are subject to change

without notice.

➢The operation manual and the product have been prepared and tested as much as possible. If you

find any misprint or error, please inform us.

➢Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may

occur through use of this product, regardless of any failure to perform on the part of this product.

➢Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may

occur with respect to any article made using this product.

For the USA

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE

STATEMENT

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated

in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference

to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Unauthorized changes or modiﬁcation to this system can void

the users authority to operate this equipment.

NOTICE

Grounding Instructions

Do not modify the plug provided - if it will not ﬁt the outlet,

have the proper outlet installed by a qualiﬁed electrician.

Check with qualiﬁed electrician or service personnel if the

grounding instructions are not completely understood, or if in

doubt as to whether the tool is properly grounded.

Use only 3-wire extension cords that have 3-prong

grounding plugs and 3-pole receptacles that accept the tool’s

plug.

Repair or replace damaged or worn out cord immediately.

For Canada

CLASS A NOTICE

This Class A digital apparatus meets all requirements of the

Canadian Interference-Causing Equipment Regulations.

CLASSE A AVIS

Cet appareil numérique de la classe A respecte toutes les

exigences du Règlement sur le matériel brouilleur du

Canada.

ROLAND DG CORPORATION

1-6-4 Shinmiyakoda, Hamamatsu-shi, Shizuoka-ken, JAPAN 431-2103

MODEL NAME : See the MODEL given on the rating plate.

RELEVANT DIRECTIVE : EC LOW VOLTAGE DIRECTIVE (73/23/EEC)

EC ELECTROMAGNETIC COMPATIBILITY DIRECTIVE (89/336/EEC)

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

As an ENERGY STAR® Partner, Roland DG Corp. has determined that this product meets the ENERGY

STAR® guidelines for energy efficiency.

The International ENERGY TAR S® Office Equipment Program is an international program that

promotes energy saving through the penetration of energy efficient computers and other office

equipment. The program backs the development and dissemination of products with functions that

effectively reduce energy consumption. It is an open system in which business proprietors can

participate voluntarily. The targeted products are office equipment such as computers, monitors, printers, facsimiles,

copiers, scanners, and multifunction devices. Their standards and logos are uniform among participating nations.

Operating Instructions

KEEP WORK AREA CLEAN. Cluttered areas and benches

invites accidents.

DON’T USE IN DANGEROUS ENVIRONMENT. Don’t

use power tools in damp or wet locations, or expose them to

rain. Keep work area well lighted.

DISCONNECT TOOLS before servicing; when changing

accessories, such as blades, bits, cutters, and like.

REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure the switch is in oﬀ position before plugging in.

USE RECOMMENDED ACCESSORIES. Consult the

owner’s manual for recommended accessories. The use of

improper accessories may cause risk of injury to persons.

NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool until it comes to a

complete stop.

Contents

To Ensure Safe Use ........................................................................................................................ 5

Pour utiliser en toute sécurité ................................................................................................... 12

Important Notes on Handling and Use ................................................................................................................. 19

Printer unit .................................................................................................................................................................... 19

Ink cartridges................................................................................................................................................................ 20

Chapter 1 Introduction ...................................................................................................................... 21

1-1 Features of the Machine ..................................................................................................................................... 22

1-2 Part Names and Functions ................................................................................................................................ 23

Printer Unit/Dryer .......................................................................................................................... 23

Operation Panel ............................................................................................................................ 25

Media Take-up System ................................................................................................................... 26

Chapter 2 Operation .......................................................................................................................... 27

2-1 Switching the Power On and Off ..................................................................................................................... 28

Switching the Power On and Off ................................................................................................... 28

The Power-saving Feature .............................................................................................................. 29

2-2 Loading and Cutting Off Media ........................................................................................................................ 30

How to Load Media ...................................................................................................................... 30

How to Cut Off Media ................................................................................................................... 35

2-3 Settings of the Media Heating System ............................................................................................................ 36

What Is the Media Heating System? .............................................................................................. 36

Making the Temperature Setting for the Media Heating System ..................................................... 36

General Guide for the Preset Temperatures ................................................................................... 37

2-4 Starting Output .................................................................................................................................................... 39

Getting Ready to Receive Data from a Computer .......................................................................... 39

Printing Tests and Cleaning ............................................................................................................ 40

2-5 If Ink Runs Out ..................................................................................................................................................... 42

Checking for Remaining Ink .......................................................................................................... 42

If Ink Runs Out .............................................................................................................................. 43

Chapter 3 Using the Cutting Feature .............................................................................................. 45

3-1 Performing Cutting .............................................................................................................................................. 46

To Perform Cutting......................................................................................................................... 46

Performing a Cutting Test ............................................................................................................... 47

Making the Setting for Blade Force ................................................................................................ 47

3-2 Performing Printing Followed Immediately by Cutting............................................................................... 48

Performing Printing Followed Immediately by Cutting .................................................................. 48

3-3 Cutting Using the Crop-mark Feature ........................................................................................................... 49

How to Use the Crop-mark Feature ............................................................................................... 49

Printing with Crop Marks .............................................................................................................. 49

Performing Cutting with Automatic Crop-mark Detection ............................................................. 51

Aligning Manually and Cutting ..................................................................................................... 52

Chapter 4 Operation of the Media Take-up System ....................................................................... 55

4-1 The Take-up System ............................................................................................................................................. 56

Features of the Take-up System ...................................................................................................... 56

Operating Conditions for the Take-up System................................................................................ 56

4-2 Using the Take-up System .................................................................................................................................. 57

How to Take Up Media ................................................................................................................. 57

How to Remove Taken-up Media .................................................................................................. 60