RetroSound Kick Panel Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für RetroSound Kick Panel (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
MODERN SOUND FOR YOUR CLASSIC
Kick Panel
Installation Guide
The information enclosed in this installation guide is intended to provide a general outline to assist
you during the process of installation. This guide does not cover every installation possibility,
vehicle, or aspect of the installation process.
Retro Manufacturing, LLC, or its subsidiaries assume no responsibility for proper or improper
installation. Every attempt has been made to make this installation guide as informative as
possible. This guide may be updated from time to time, and speciîš¿cations are subject to change
without notice. Please check our website (www.retromanufacturing.com) for the latest updates.
Kick Panel
Remove the existing kick panels by removing any screws or press clips holding the panels
in place. It may be necessary to remove the rubber door seal îš¿rst to remove the kick panels.
Route the speaker wires before installing your speakers. Always avoid sharp edges that
could fray or cut the wiring and use rubber grommets to protect the speaker wires that need
to be routed through metal. For the best quality connection and to minimize signal loss,
always use high-quality connectors. Never run wires outside the vehicle.
Mount the new kick panels using the fasteners from the factory kick panels. You may need
to drill new mounting holes in the kick panels before mounting.
INSTALLATION
Thank you for purchasing RetroSound® Kick Panels. RetroSound® Kick Panels are expertly
molded for a perfect îš¿t. The speaker mounts are angled to direct sound upwards towards
the listener for better stereo imaging.
Precautions
It is best to consult a professional installation specialist to help with your installation.
Important Installation Guidelines:
• Carefully read and understand the instructions before attempting installation.
• Always disconnect the negative (-) battery terminal before beginning any work.
Failure to do so may result in damage to the unit, îš¿re, injury, or death.
• Use high-quality connectors to prevent re or damage to the unit.
• Carefully check the installation area before drilling to ensure you won’t drill into the
gas tank, fuel lines, brake lines, hydraulic lines, vacuum lines, or electrical wiring.
• Never run the speaker wires underneath the vehicle.
• Avoid running speaker wires over sharp edges and use rubber grommets to protect
wires when routed through metal panels.
Step #4 Mount Kick Panels
Step #1 Remove Existing Kick Panels
Step #2 Route Speaker Wires
Step #3 (Optional) Cut Speaker Holes
If you are using larger speakers, you will
need to enlarge the speaker opening in
the kick panels. Use a speaker grill ring as
a template to mark the size of the space
required and the locations for the speaker’s
mounting screws. Use a razor knife or
Dremel tool to carefully enlarge the opening
and a 1/8-inch drill bit to drill the mounting
holes.
Kick Panel
Step #5 Connect the Speakers
Step #6 Mount the Speakers
Step #7 Complete the Installation
Kick Panel
Kick Panel
Kick Panel
Feed the speaker wires through the
speaker opening and connect to the
speaker terminals.
Connect the negative wire to the negative (-)
speaker terminal and positive to the positive
(+) speaker terminal.
Fit the speaker into the cutout and
secure it using the supplied screws.
If needed, place a speed clip over
each drilled hole before mounting
the speaker. (Some models may
require placing the grill base before
placing the speaker.)
Tighten all screws until the speaker is snug
and in place to prevent rattling. Be careful
not to overtighten the screws. Complete the
installation by placing the grill (if included)
over the installed speaker.
NEGATIVE
POSITIVE
TIP: How to Remove Speaker Grills
To remove speaker grills either pull up on the grill’s ring (Type A) or push down on the grill’s ring (Type B).
Type B: Push down to removeType A: Pull up to remove


Produktspezifikationen

Marke: RetroSound
Kategorie: Nicht kategorisiert
Modell: Kick Panel

Brauchst du Hilfe?

Wenn Sie Hilfe mit RetroSound Kick Panel benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert RetroSound

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-