Projecta HDBC20 Bedienungsanleitung

Projecta Ladegerät HDBC20

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Projecta HDBC20 (16 Seiten) in der Kategorie Ladegerät. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/16
6/12/24 VOLT AUTOMATIC/MANUAL
WORKSHOP
BATTERY CHARGER
P/No.s HDBC20, HDBC35
WARNING
• Explosive gases. Prevent flames and sparks. Provide adequate ventilation during charging.
• Before charging, read the instructions.
• For indoor use. Do not expose to rain.
• For charging lead acid batteries ONLY (of the size & voltage specified in the specifications table).
• Always charge the battery on the correct voltage setting. Never set the charger to a higher voltage
than the battery.
• Disconnect the 240V mains supply before making or breaking the connections to the battery.
• Do not attempt to charge non-rechargeable batteries.
• Never charge a frozen battery.
• This appliance is not intended for use by young children or infirm persons unless they have been
adequately supervised by a responsible person to ensure that they can use the appliance safely.
• Young children should be supervised to ensure that they do not play with the appliance.
• Charge the battery in a suitable area, as the battery may give off corrosive fumes which could
damage delicate surfaces.
• Ensure all vehicle accessories and lights are turned off prior to charging.
• If the AC cord is damaged, it must be returned to an authorized Service Center.
2
3
FEATURES
Automatic Charging
When in automatic mode the charger will stop charging the battery when the battery is fully charged.
You can leave the charger connected to the battery without risk of overcharging. Once the battery is full,
the battery charger will automatically start to maintain the battery. The charger monitors the battery voltage
and continues to top up the battery, keeping it fully charged and ready for use.
Manual Charging
The charger in this mode will continue to charge the battery until the timer finishes or is turned off and
requires the user to monitor the charging battery. When used by experienced users it can deliver an
equalization charge to balance the voltage in the battery’s cells.
LED Indication
OVERLOAD (Red LED Flashing): The LED will flash when the transformer or the current regulators (SCR’s)
have got too hot
POWER ON (Red LED ON): The LED comes on when connected to power and the charger is switched on
POWER ON (Red LED Flashing): Indicates that the battery clamps have been connected in reverse polarity
Charging (Orange LED on): The LED comes on indicating charging
Fully charged (Green LED on): The LED comes on when the battery is charged
VOLT (Red LED ON): The LED indicates that Voltage is being displayed
AMP (Red LED ON): The LED indicates that Amps or current is being displayed
LED Voltage/Amp Display
The charger has a VOLT and AMP meter built in. When the charger is initially powered up the display will
show voltage. When the VOLT / AMP button is pressed the Amps will be displayed, press the button again
the display will go back to Volts. When Volts is displayed this indicates the state of charge of the battery,
when Amps is displayed this indicates how much charge is being accepted by the battery.
Override Button
The battery charger measures the battery voltage at the clamps to determine if the battery is correctly
connected. A reading above 3V will activate the battery charger. In some instances where the battery is
extremely flat, it is possible to have correct connection and the battery to be below the 3V limit. In this
instance check the battery leads to ensure they are connected correctly and press the OVERRIDE button
to activate the battery charger.
Multi Voltage
Suitable for charging 6V, 12V & 24V batteries.

Produktspezifikationen

Marke: Projecta
Kategorie: Ladegerät
Modell: HDBC20

Brauchst du Hilfe?

Wenn Sie Hilfe mit Projecta HDBC20 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Ladegerät Projecta

Projecta

Projecta BLT700 Bedienungsanleitung

13 September 2024
Projecta

Projecta PC2100 Bedienungsanleitung

2 September 2024
Projecta

Projecta IC5000 Bedienungsanleitung

5 August 2024
Projecta

Projecta IC2500 Bedienungsanleitung

2 August 2024
Projecta

Projecta IC1500L Bedienungsanleitung

1 August 2024
Projecta

Projecta IC1500 Bedienungsanleitung

30 Juli 2024
Projecta

Projecta BM320 Bedienungsanleitung

29 Juli 2024
Projecta

Projecta AC250B Bedienungsanleitung

28 Juli 2024
Projecta

Projecta BLT100 Bedienungsanleitung

27 Juli 2024
Projecta

Projecta BLT200 Bedienungsanleitung

27 Juli 2024

Bedienungsanleitung Ladegerät

Neueste Bedienungsanleitung für -Kategorien-

MSW

MSW S-CHARGER-20A.2 Bedienungsanleitung

16 Oktober 2024
MSW

MSW S-CHARGER-10A.2 Bedienungsanleitung

16 Oktober 2024
ABB

ABB EVLunic Bedienungsanleitung

9 Oktober 2024
Powerplus

Powerplus POWDP9062 Bedienungsanleitung

8 Oktober 2024
Cellular Line

Cellular Line Wireless Power Dock Bedienungsanleitung

7 Oktober 2024
HQ

HQ CHARGER14 Bedienungsanleitung

4 Oktober 2024
Makita

Makita DC18RD Bedienungsanleitung

4 Oktober 2024
HQ

HQ CH02E Bedienungsanleitung

2 Oktober 2024
Venom

Venom VS5007 Bedienungsanleitung

1 Oktober 2024
Venom

Venom VS5010 Bedienungsanleitung

1 Oktober 2024