Pro-Form PFMC99110 Bedienungsanleitung

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Pro-Form PFMC99110 (12 Seiten) in der Kategorie Hartslagmeter. Dieser Bedienungsanleitung war fĂĽr 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
Heart Rate Monitor User’s Guide Model No.
PFMC99110
Congratulations for purchasing the new AccuRate™
heart rate monitor. To install and use the heart rate
monitor, read and follow all instructions in this
user’s guide. For detailed instructions about using
the heart rate monitor with your treadmill, refer to the
user’s manual included with your treadmill.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause unde-
sired operation. Changes or modifications not ex-
pressly approved by ICON Health & Fitness, Inc.
could void the user’s authority to operate this device.
WARNING
If you have an implanted medical device such
as a pacemaker, check with your physician be-
fore using the heart rate monitor.
If you have heart problems, or if you are over 60
years of age and have been inactive, do not use
pulse-driven programs.
If you are taking medication regularly, consult
your physician to find whether the medication
will affect your exercise heart rate.
2
How to Install the Receiver
Before the heart rate monitor can be used, the included receiver must be installed. Pages 2 through 7 of this
user’s guide include eight sections that show how the receiver is to be installed in eight different styles of tread-
mills. Look at pages 2 through 7 and find the drawings that most closely resemble your treadmill. Then,
follow the instructions in that section to install the receiver. Note: Your treadmill may not look exactly like the
treadmills shown in the drawings. If you have questions, call toll-free 1-800-999-3756.
1. Make sure that the power cord is unplugged. Remove
the indicated Screws from the Console Back (A).
Important: The Screws may be different lengths. Keep
track of which Screws were removed from which holes.
2. Peel the paper off the pad on the bottom of the Receiver
(B). Turn the Receiver so the cylinder is on the side
shown, and press the Receiver into the bottom of the
Console Base (C) in the indicated location.
A
C
Screws
1
2C
B
Cylinder
3. Connect the Short Jumper Wire (D) to the wire on the
Receiver (B). Connect the other end of the Short Jumper
Wire to the PULSE jack on the back of the Console (C). If
there is a wire already plugged into the PULSE jack, un-
plug it. Note: The included Long Jumper Wire can be dis-
carded. The Wire Tie can be used to tie wires if needed.
Make sure that no wires are pinched. See step 1.
Reattach the Console (C) with the 1” Screws, 1 3/4”
Screws, and 2” Screws. Important: If the Screws are
not put back into the same holes that they were
removed from, the Console will be damaged.
3C
B
D
PULSE
Jack
3
1. Make sure that the power cord is unplugged. Remove
the indicated Screws (A) from the Console Back (B).
2. Peel the paper off the pad on the bottom of the Receiver
(C). Turn the Receiver so the cylinder is on the side
shown, and press the Receiver into the bottom of the
Console Back (B) in the indicated location.
Connect the Short Jumper Wire (D) to the wire on the
Receiver (C). Connect the other end of the Short Jumper
Wire to the PULSE jack on the back of the Console (E).
Note: The included Long Jumper Wire can be discarded.
The Wire Tie can be used to tie wires if needed.
Make sure that no wires are pinched. See step 1.
Reattach the Console Base (E) with the Screws (A).
B
E
A
1
2
PULSE
Jack
D
E
C
B
Cylinder

Produktspezifikationen

Marke: Pro-Form
Kategorie: Hartslagmeter
Modell: PFMC99110

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pro-Form PFMC99110 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten