Pro-Form PFMC8992 Bedienungsanleitung
Pro-Form
Herzfrequenzmesser
PFMC8992
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Pro-Form PFMC8992 (12 Seiten) in der Kategorie Herzfrequenzmesser. Dieser Bedienungsanleitung war fĂĽr 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/12
Heart Rate Monitor User’s Guide Model No. PFMC89820
Model No. PFMC89920
Congratulations for purchasing the new AccuRate™
heart rate monitor. To install and use the heart rate
monitor, read and follow all instructions in this
user’s guide. For detailed instructions about using
the heart rate monitor with your exercise equipment,
refer to the user’s manual included with your exercise
equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause unde-
sired operation. Changes or modifications not ex-
pressly approved by ICON Health & Fitness, Inc.
could void the user’s authority to operate this device.
WARNING
If you have an implanted medical device such
as a pacemaker, check with your physician be-
fore using the heart rate monitor.
If you have heart problems, or if you are over 60
years of age and have been inactive, do not use
pulse-driven programs.
If you are taking medication regularly, consult
your physician to find whether the medication
will affect your exercise heart rate.
2
How to Install the Receiver
Before the heart rate monitor can be used, the included receiver must be installed.
To install the receiver in an exercise cycle or an elliptical crosstrainer, refer to the instructions in your exer-
cise cycle user’s manual or elliptical crosstrainer user’s manual. After you have installed the receiver, refer to
pages 10 and 11 of this user’s guide. Note: If you have lost your user’s manual, go to www.iconservice.com on
the World Wide Web, or call toll-free 1-800-999-3756.
To install the receiver in a treadmill, refer to the instructions in your treadmill user’s manual. After you have in-
stalled the receiver, refer to pages 10 and 11 of this user’s guide. Note: If you have lost your user’s manual, go to
www.iconservice.com on the World Wide Web, or call toll-free 1-800-999-3756. If your treadmill user’s manual
does not include instructions for installing the receiver, refer to pages 2 through 9 of this user’s manual.
Pages 2 through 9 include 11 different sections that show how the receiver should be installed in different styles
of treadmills. Find the drawings that most closely resemble your treadmill, and follow the instructions in that sec-
tion to install the receiver. Note: Your treadmill may not look exactly like the treadmills shown in the drawings. If
you have questions, call toll-free 1-800-999-3756.
1. Make sure that the power cord is unplugged. Remove
the indicated Screws from the Console Back (A).
Important: The Screws may be different lengths. Keep
track of which Screws were removed from which holes.
2. Peel the paper off the pad on the bottom of the Receiver
(B). Turn the Receiver so the cylinder is on the side
shown, and press the Receiver into the bottom of the
Console Base (C) in the indicated location.
A
C
Screws
1
2C
B
Cylinder
3. Connect the included Short Jumper Wire (D) to the wire
on the Receiver (B). Connect the other end of the Short
Jumper Wire to the PULSE 2 or PLS2 jack on the back of
the Console (C). If there is a wire already plugged into
the PULSE 2 jack, unplug it. Note: The other wires in-
cluded with the receiver may be discarded. The Wire Tie
can be used to tie wires, if needed.
Make sure that no wires are pinched. See step 1.
Reattach the Console (C) with the Screws. Important: If
the Screws are not put back into the same holes from
which they were removed, the Console will be dam-
aged.
C
PLS2
Jack
PULSE 2
Jack
3
DB
3
1. Make sure that the power cord is unplugged. Remove
the indicated Screws (A) from the Console Back (B).
2. Peel the paper off the pad on the bottom of the Receiver
(C). Turn the Receiver so the cylinder is on the side
shown, and press the Receiver into the bottom of the
Console Back (B) in the indicated location.
Connect the included Short Jumper Wire (D) to the wire on
the Receiver (C). Connect the other end of the Short
Jumper Wire to the PULSE jack on the back of the Console
(E). Note: The other wires included with the receiver may
be discarded. The Wire Tie can be used to tie wires, if
needed.
Make sure that no wires are pinched. See step 1.
Reattach the Console (E) with the Screws (A).
B
E
A
1
2
PULSE
Jack
D
E
C
B
Cylinder
Produktspezifikationen
| Marke: | Pro-Form |
| Kategorie: | Herzfrequenzmesser |
| Modell: | PFMC8992 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Pro-Form PFMC8992 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Herzfrequenzmesser Pro-Form
19 August 2024
12 August 2024
11 August 2024
7 August 2024
6 August 2024
2 August 2024
Bedienungsanleitung Herzfrequenzmesser
- Herzfrequenzmesser Medion
- Herzfrequenzmesser Beurer
- Herzfrequenzmesser Dexford
- Herzfrequenzmesser Medisana
- Herzfrequenzmesser Polar
- Herzfrequenzmesser Pyle
- Herzfrequenzmesser Garmin
- Herzfrequenzmesser Lanaform
- Herzfrequenzmesser Sanitas
- Herzfrequenzmesser Terraillon
- Herzfrequenzmesser Suunto
- Herzfrequenzmesser Sigma
- Herzfrequenzmesser Domyos
- Herzfrequenzmesser Maxxus
- Herzfrequenzmesser CicloSport
- Herzfrequenzmesser Runtastic
- Herzfrequenzmesser BBB
- Herzfrequenzmesser Flow Fitness
- Herzfrequenzmesser Timex
- Herzfrequenzmesser Echowell
- Herzfrequenzmesser IGPSPORT
- Herzfrequenzmesser Lezyne
- Herzfrequenzmesser Wahoo Fitness
- Herzfrequenzmesser Oregon Scientific
- Herzfrequenzmesser Fusion Sport
- Herzfrequenzmesser Iriver
- Herzfrequenzmesser Osynce
- Herzfrequenzmesser Ciclo
- Herzfrequenzmesser BBB Cycling
Neueste Bedienungsanleitung fĂĽr -Kategorien-
17 September 2024
3 September 2024
3 September 2024
2 September 2024
30 August 2024
29 August 2024
27 August 2024