Porter-Cable 382 Bedienungsanleitung

Porter-Cable Schleifmaschine 382

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Porter-Cable 382 (7 Seiten) in der Kategorie Schleifmaschine. Dieser Bedienungsanleitung war für 33 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/7

DEFINITIONS - SAFETY GUIDELINES

indicates an imminently hazardous situation which, if not avoid-

ed, result in will death or serious injury.

indicates a potentially hazardous situation which, if not avoided,

could death or serious injury. result in

indicates a potentially haz ard ous situation which, if not avoided,

may minor or mod er ate injury.result in

NOTICE

used without the safety alert symbol indicates potentially haz-

ardous situation which, if not avoided, result in may property damage.

To reduce the risk of injury, read the instruction manual.

GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and instructions Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

Save all warningS and inStructionS

for future reference

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of flam-

mable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol

or medication. A moment of inattention while operating power tools may result in serious per-

sonal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before connect-

ing to power source and/or battery pack, picking up or carrying the tool. Carrying power

tools with your finger on the switch or energizing power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are dan-

gerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these instructions

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical replace-

ment parts. This will ensure that the safety of the power tool is maintained.

ADDITIONAL SPECIFIC SAFETY RULES

• Hold power tools by insulated gripping surfaces when performing an operation where the cut-

ting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

• Do not sand metal of any kind with your sander. Sparks may be generated by sanding screws,

nails or other metals which may ignite dust particles.

• Do not wet sand with this sander. Liquids may enter the motor housing and cause electric

shock.

• Empty dust collection system frequently, especially when sanding resin-coated surfaces such

as polyurethane, varnish, shellac, etc. Dispose of coated dust particles according to the finish

manufacturer’s guidelines, or place in a metal can with a tight fitting metal lid. Remove coated

dust particles from the premises daily. The accumulation of fine sanding dust particles may self

ignite and cause fire.

• Do not operate this tool for long periods of time. Vibration caused by the operating action of this

tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion,

take frequent rest periods, and limit daily time of use.

• Sanding of lead-based paint, chemically pressure treated lumber or other materials that may

contain carcinogens is not recommended. Sanding of these materials should only be performed

by a professional.

• Clean out your tool often, especially after heavy use. Dust and grit containing metal particles

often accumulate on interior surfaces and could create a risk of serious injury, electric shock or elec-

trocution. Always disconnect the sander from the power source before cleaning. Always wear safety

glasses that conform to ANSI Z87.1.

• Always disconnect tool from the power source before changing abrasive sheets. Such preven-

tive safety measures reduce the risk of starting the power tool accidentally.

• Replace worn CFS disc when it causes high tool rpm. High tool rpm caused by a worn out CFS

disc may result in separation of sanding pad from the sander, possibly causing personal injury.

for instructions on replacing the CFS disc, see the section of this manual titled “Tool Care.”

EXTENSION CORD

An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety.

The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge

has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in

loss of power and overheating. When using more than one extension to make up the total length, be

sure each individual extension contains at least the minimum wire size. The following table shows

the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the

next heavier gauge. The smaller the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

Always use eye protection. All users and bystanders must wear eye protection that

conforms to ANSI Z87.1.

Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration of use, noise from this product may contribute to

hearing loss.

ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with approved

safety equipment, such as those dust masks that are specially designed to filter out microscopic

particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and wash exposed areas with soap and

water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption

of harmful chemicals.

Use of this tool can generate and/or disburse dust, which may cause serious and perma-

nent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for

the dust exposure. Direct particles away from face and body.

SYMBOLS

The label on your tool may include the following symbols.

The symbols and their definitions are as

follows:

V ....................... volts A ................. amperes

Hz .................... hertz W ................ watts

min ................... minutes .............. alternating current

................ direct current .............. alternating or direct current

..................... Class I Construction no ............... no load speed

......................... (grounded) ............... earthing terminal

.................... Class II Construction ............... safety alert symbol

......................... (double insulated) BPM ........... beats per minute

…/min .............. per minute RPM ........... revolutions per minute

OPM ................ orbits per minute

ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

1. Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the

contaminated dust. The greatest danger of lead poisoning is to children and pregnant women.

2. Since it is difficult to identify whether or not a paint contains lead without a chemical analysis, we

recommend the following precautions when sanding any paint:

PERSONAL SAFETY

1. No children or pregnant women should enter the work area where the paint sanding is being

done until all clean up is completed.

2. A dust mask or respirator should be worn by all persons entering the work area. The filter should

be replaced daily or whenever the wearer has difficulty breathing. See your local hardware store

for the proper NIOSH approved dust mask.

Instruction manual

Manuel d'instructions

Manual de'instrucciones

382

www.deltaportercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS

DE SERVICIO Y PÓLIZA DE GARANTÍA.

LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

5" (127 mm) Random

oRbit Palm SandeR

with Dust Collection and Hook & Loop Pad

Lijadora de órbita aleatoria de

127 mm (5 pulg)

con recolección de polvo y

base de unión por contacto

Ponceuse de ﬁnition orbitale

excentrique, de 127 mm (5 po)

avec dépoussiéreur et tampon

de type boucles et crochets

3. NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting

contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking or

smoking. Articles of food, drink, or smoking should not be left in the work area where dust would

settle on them.

ENVIRONMENTAL SAFETY

1. Paint should be removed in such a manner as to minimize the amount of dust generated.

2. Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mil thickness.

3. Sanding should be done in a manner to reduce tracking of paint dust outside the work area.

CLEANING AND DISPOSAL

1. All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration

of the sanding project. Vacuum filter bags should be changed frequently.

2. Plastic drop cloths should be gathered up and disposed of along with any dust chips or other

removal debris. They should be placed in sealed refuse receptacles and disposed of through

regular trash pick-up procedures. During clean up, children and pregnant women should be kept

away from the immediate work area.

3. All toys, washable furniture and utensils used by children should be washed thoroughly before

being used again.

Save theSe inStructionS

MOTOR

Be sure your power supply agrees with nameplate marking. 120 Volts AC means your tool will operate on

alternating current. As little as 10% lower voltage can cause loss of power and can result in overheating.

All PORTER-CABLE tools are factory-tested; if this tool does not operate, check the power supply.

Accessories must be rated for at least the speed recommended on the tool warning label.

Accessories running over rated speed can fly apart and cause injury. Accessory ratings must always be

above tool speed as shown on tool nameplate.

To reduce the risk of injury, turn unit off and disconnect it from power source before

installing and removing accessories, before adjusting or when making repairs.

An accidental start-

up can cause injury.

OPERATION

To reduce the risk of injury, turn unit off and disconnect it from power source

before installing and removing accessories, before adjusting or when making repairs. An acci-

dental start-up can cause injury.

Never modify any parts of the power tool. Damage or personal injury could result.

INTENDED USE

The 382 random orbit palm sander has been designed for professional sanding at various work sites

(i.e., construction sites). Do not use under humid conditions or in presence of flammable liquids or

gases.

This random orbit palm sander is a professional power tool. Do not let children come into contact with

the tool. Supervision is required when inexperienced operators use this tool.

ATTACHING SANDING DISCS (FIG. 1)

To reduce the risk of injury, turn unit off and disconnect it from power source

before installing and removing accessories, before adjusting or when making repairs. An acci-

dental start-up can cause injury.

Your sander is designed to use 5" (127 mm) sanding discs. Discs have an 8 hole dust extraction

pattern and hook and loop attachment. To attach paper to the sanding pad:

REQUIRED SANDPAPERS

Disc Size Attachment Method Hole Pattern

(127 mm) Hook & Loop 8 holes

1. Turn off and unplug the tool.

2. Turn the sander over so that the sanding pad is facing upward.

3. Clean dust from the vinyl pad face.

4. Hold the pad with one hand to keep it from rotating.

5. With the other hand, align the holes if they are present, and place the disc directly on top of

the pad.

NOTE

: Do not use sanding screen (e.g. screen used for sanding drywall) directly on the hook

and loop pad. The screen will not hold and will damage the hooks on the pad. The hooks on the

pad will wear very rapidly if left in contact with the work surface while the tool is operating.

SWITCH (FIG. 2)

To reduce the risk of injury, make sure the sander is not resting on the workpiece when

the switch is turned on.

To turn the unit on, depress the side of the dust protected switch that corresponds to the sym-

bol “I”. To turn the tool off, depress the side of the switch that corresponds to the symbol “O”.

DUST EXTRACTION (FIG. 3, 4)

To reduce the risk of injury, turn unit off and disconnect it from power source before

installing and removing accessories, before adjusting or when making repairs. An accidental

start-up can cause injury.

To reduce the risk of serious personal injury, NEVER operate this tool with perforated

paper unless the dust collection system is in place.

Empty dust collection system frequently, especially when sanding resin-coated surfaces

such as polyurethane, varnish, shellac, etc. Dispose of coated dust particles according to the ﬁnish

manufacturer’s guidelines, or place in a metal can with a tight ﬁtting metal lid. Remove coated dust

particles from the premises daily. The accumulation of ﬁne sanding dust particles may self ignite and

cause ﬁre.

Your sander comes equipped with a cloth bag to collect the dust generated during sanding. It

was designed to be very durable and efficient yet easy to empty. To empty the dust collection

bag:

1. Turn off and unplug tool.

2. While holding the canister, twist to unlock and remove the adapter. (Fig. 3)

3. Gently empty the bag and shake out the adapter. (Fig. 4)

You may notice that all the dust will not come free from the bag. This will not affect sanding

performance but will reduce the sander’s dust collection efficiency. To restore your sander’s dust

collection efficiency, depress the spring inside the dust bag when you are emptying it and tap it

on the side of the trash can or dust receptacle.

Never operate this tool unless the dust collector is in place. Sanding dust exhaust

may create a breathing hazard.

OPERATION (FIG. 5, 6)

To operate your sander, grasp it as shown in figures 5 or 6 and turn it on. Move the unit in long,

sweeping strokes along the surface being sanded, letting the sander do the work.

Pushing down on the tool while sanding actually slows the removal rate and produces an inferior

quality surface. Be sure to check your work often, this sander is capable of removing material

rapidly, especially with coarse paper.

The random orbital action of your sander allows you to sand with the grain or at any angle

across it for most sanding jobs. To produce the best finish possible, start with coarse grit sand-

paper and change gradually to finer and finer paper. Vacuum and wipe surface with a tack cloth

between grit steps.Your sander is designed to sand into small or confined areas. Its small size

and light weight make it ideal for overhead work.

If your sander has the dust collection feature, the rate at which the dust collection bag fills up

will vary with the type of material being sanded and the coarseness of the sandpaper. For best

results, empty the bag frequently. When sanding painted surfaces, (see the following for addi-

tional precautions when sanding paint) you may find that the sandpaper loads up and clogs with

paint. A heat gun will work much better to remove paint before sanding. FOLLOW ALL SAFETY

INSTRUCTIONS IN HEAT GUN INSTRUCTION MANUAL.

TROUBLESHOOTING

For assistance with your tool, visit our website at www.deltaportercable.com for a list of service centers, or

call the PORTER-CABLE Customer Care Center at (888) 848-5175.

MAINTENANCE

To reduce the risk of injury, turn unit off and disconnect it from power source before

installing and removing accessories, before adjusting or when making repairs. An accidental start-up

can cause injury.

ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS wear certified safety equipment:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3)

• ANSI S12.6 (S3.19) hearing protection

• NIOSH/OSHA/MSHA respiratory protection.

REPAIRS

For assistance with your tool, visit our website at www.deltaportercable.com for a list of service centers,

or call the PORTER-CABLE Customer Care Center at (888) 848-5175.

CLEANING

Periodically blowing dust and chips out of the motor housing using clean, dry compressed

air is a suggested maintenance procedure. To reduce the risk of serious personal injury, ALWAYS wear

ANSI Z87.1 safety glasses while using compressed air.

When cleaning, use only mild soap and a damp cloth on plastic parts. Many household

cleaners contain chemicals which could seriously damage plastic. Also, do not use gasoline, turpentine,

lacquer, paint thinner, dry cleaning fluids or similar products which may seriously damage plastic parts.

NEVER let any liquid get inside the tool; NEVER immerse any part of the tool into a liquid.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in

the outlet. Also, check for blown fuses or open circuit breakers in the line.

TOOL CARE (FIG. 7, 8

1. Keep your sander as clean as possible by wiping with a clean cloth and blowing air through

it after every 5 hours of use.

2. As part of CFS (Controlled Finishing System), your sander is equipped with a replaceable disc

which is located between the pad and the shroud. It is designed to increase the dust collection

efficiency and control the pad speed while the unit is off the work. The disc is designed to be a

consumable part and will occasionally need to be replaced. Replacement is necessary when the

pad speed increases very dramatically when the unit is lifted from the work surface. To replace

your CFS disc:

a. Turn off and unplug tool.

b. Remove 3 screws from the bottom of the pad.

c. Remove the pad.

d. Snap out worn disc.

e. Snap in new disc, aligning notch in disc with cut out in shroud shown in Fig. 7.

f. Press in new disc around the edges using both hands to ensure that the disc is

inserted snugly into the shroud as shown in figure 8.

g. Replace the pad and the 3 screws.

3. Avoid overloading your sander. Overloading will result in a considerable reduction in speed

and finish quality of your work. The unit may also become hot. In this event, run sander at

a no load condition for a minute or two.

4. If you wrap the cord around the tool when you store it, leave a generous loop of cord such

that the strain relief does not bend. This helps prevent premature cord failure.

BRUSH REPLACEMENT (FIG. 9, 10)

To reduce the risk of injury, turn unit off and disconnect it from power source before

installing and removing accessories, before adjusting or when making repairs. An accidental start-up

can cause injury.

Follow these directions to replace the tool’s brushes:

1. Remove the three screws located in the top cap, as shown in figure 9.

2. Lift off the top cap. Observe the brush holders (D) and wires leading from the brushes to

the motor field, as shown in figure 10.

3. Pull the wires from the motor field and then lift and hold out of the way of one of the brush

springs (E).

FIG. 2FIG. 1

FIG. 3 FIG. 4

FIG. 5 FIG. 6

FIG. 7 FIG. 8

FIG. 9

FIG. 10

MESURES DE SÉCURITÉ - DÉFINITIONS

Indique une situation dangereuse imminente qui, si elle n’est pas évitée,

causera la mort ou des blessures graves.

Indique une situation potentiellement dangereuse qui, si elle n’est

pas évitée, se solder par un pourrait décès ou des blessures graves.

Indique une situation potentiellement dangereuse qui, si elle n’est pas

évitée se solder par pourrait des blessures mineures ou modérées.

AVIS

Utilisé sans le symbole d’alerte à la sécurité, indique une situation

potentiellement dangereuse qui, si elle n'est pas évitée se solder pourrait par des

dommages à la propriété.

Afin de réduire le risque de blessures, lire le mode d’emploi de l’outil.

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX POUR LES OUTILS

ÉLECTRIQUES

Lire tous les avertissements de sécurité et les directi-

ves. Le non-respect des avertissements et des directives

pourrait se solder par un choc électrique, un incendie et/ou

une blessure grave.

conServer touS leS avertiSSementS et touteS leS

directiveS pour un uSage ultérieur

Le terme « outil électrique » cité dans les avertissements se rapporte à votre outil électrique à alimen-

tation sur secteur (avec fil) ou par piles (sans fil).

1) SÉCURI

TÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont propices

aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel qu’en présence

de liquides, de gaz ou de poussières inflammables. Les outils électriques produisent des

étincelles qui pourraient enflammer la poussière ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un outil électrique.

Une distraction pourrait en faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation avec un outil électrique

mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de fiches non modifiées

correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux, des

radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc électrique est plus élevé

si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de l’eau dans

un outil électrique augmente le risque de choc électrique.

4. Remove the old brush from the brush holder and discard the brush/wire assembly. Still

holding the brush spring out of the way, insert the new brush and release the spring against

the back of the brush. Then plug the wire into the motor field. Repeat the procedure for the

second brush.

5. Replace the top cap and tighten the three screws that hold it in place. Always replace both

brushes.

LUBRICATION

Self lubricating bearings are used in the tool and periodic relubrication is not required. However,

it is recommended that, once a year, you take or send the tool to a service center for a thorough

cleaning and inspection.

SERVICE

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at

www.deltaportercableservicenet.com. You can also order parts from your nearest PORTER-CABLE

Factory Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our

Customer Care Center at (888) 848-5175.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about

PORTER-CABLE, its factory service centers or authorized warranty service centers, visit our website at

www.deltaportercable.com or call our Customer Care Center at (888) 848-5175. All repairs made by our

service centers are fully guaranteed against defective material and workmanship. We cannot guarantee

repairs made or attempted by others.

You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson, Tennessee

38305 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of

your tool (model number, type, serial number, etc.).

ACCESSORIES

Since accessories, other than those offered by PORTER-CABLE, have not been tested with

this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only

PORTER-CABLE recommended accessories should be used with this product.

A complete line of accessories is available from your PORTER-CABLE Factory Service Center or a

PORTER-CABLE Authorized Warranty Service Center. Please visit our Web Site www.deltaportercable.

com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair, without charge, any defects due to faulty materials or workmanship for three

years from the date of purchase. This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit www.deltaportercable.

com or call (888) 848-5175. This warranty does not apply to accessories or damage caused where repairs

have been made or attempted by others. This warranty gives you specific legal rights and you may have

other rights which vary in certain states or provinces.

In addition to the warranty, PORTER-CABLE tools are covered by our:

1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn parts caused by normal

use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the performance of your

PORTER-CABLE Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date

of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in

Latin America, see country specific warranty information contained in the packaging, call the local com-

pany or see website for warranty information.

To register your tool for warranty service visit our website at www.deltaportercable.com.

WARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call (888) 848-5175 for a free replacement.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour transporter,

tirer ou débrancher un outil électrique. Tenir le cordon éloigné de la chaleur, de l’huile, des

bords tranchants et des pièces mobiles. Les cordons endommagés ou enchevêtrés augmen-

tent les risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge convenant à

cette application. L’utilisation d’une rallonge conçue pour l’extérieur réduira les risques de choc

électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit d’alimentation dotés d’un disjoncteur de

fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur réduit les risques de choc élec-

trique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un outil élec-

trique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou sous l’influence de

drogues, d’alcool ou de médicaments. Un simple moment d’inattention en utilisant un outil

électrique peut entraîner des blessures corporelles graves.

b) Utiliser des équipements de protection individuelle. Toujours porter une protection oculai-

re. L’utilisation d’équipements de protection comme un masque antipoussière, des chaussures

antidérapantes, un casque de sécurité ou des protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessures corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à la position

d’arrêt avant de relier l’outil à une source d’alimentation et/ou d’insérer un bloc-piles, de

ramasser ou de transporter l’outil. Transporter un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont l’interrupteur est à la position de marche risque

de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique peut provoquer des blessures corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de mieux

maîtriser l’outil électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de bijoux. Garder

les cheveux, les vêtements et les gants à l’écart des pièces mobiles. Les vêtements amples,

les bijoux ou les cheveux longs risquent de rester coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement de dispositifs de dépoussiérage et

de ramassage, s’assurer que ceux-ci sont bien raccordés et utilisés. L’utilisation d’un dis-

positif de dépoussiérage peut réduire les dangers engendrés par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse pour laquelle

il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil électrique

dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil électrique

avant de faire tout réglage ou changement d’accessoire ou avant de ranger l’outil. Ces

mesures préventives réduisent les risques de démarrage accidentel de l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants et ne permettre à aucune per-

sonne n’étant pas familière avec un outil électrique ou son mode d’emploi d’utiliser cet

outil. Les outils électriques deviennent dangereux entre les mains d’utilisateurs inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces mobiles sont mal alignées ou coin-

cées, si des pièces sont brisées ou présentent toute autre condition susceptible de nuire

au bon fonctionnement de l’outil électrique. En cas de dommage, faire réparer l’outil

électrique avant toute nouvelle utilisation. Beaucoup d’accidents sont causés par des outils

électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe bien entrete-

nus et affûtés sont moins susceptibles de se coincer et sont plus faciles à maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux présentes

directives en tenant compte des conditions de travail et du travail à effectuer. L’utilisation

d’un outil électrique pour toute opération autre que celle pour laquelle il a été conçu est dange-

reuse.

5) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant que des piè-

ces de rechange identiques. Cela permettra de maintenir une utilisation sécuritaire de l’outil

électrique.

RÈGLES DE SÉCURITÉ SPÉCIFIQUE

• Tenir l’outil par sa surface de prise isolée dans une situation où l’outil de coupe peut entrer

en contact avec un câblage caché ou avec son propre cordon d’alimentation. Tout contact

avec un fil « sous tension » mettra « sous tension » les pièces métalliques exposées de l’outil et

provoquera un choc électrique chez l’opérateur de l’outil.

• Ne pas poncer de surfaces métalliques de tout type avec la ponceuse. Le ponçage de vis,

clous ou autres pièces métalliques produit des étincelles qui pourraient enflammer des particules

de poussière.

• Ne pas poncer à l’eau avec la présente ponceuse. Du liquide risque de pénétrer le boîtier du

moteur et ainsi provoquer un choc électrique.

• Vider souvent le dépoussiéreur, particulièrement lors du ponçage de surfaces enduites de

matières à base de résine comme du polyuréthanne, du vernis, du vernis à la gomme laque, etc.

Éliminer les particules de poussière enduites de produit selon les recommandations du fabricant

du fini ou les amasser dans une boîte de métal avec un couvercle bien ajusté. Les retirer des

lieux quotidiennement. L’accumulation de particules fines de poussière risque de s’enflammer

spontanément et provoquer un incendie.

• Ne pas faire fonctionner cet outil durant de longues périodes. Les vibrations causées par le

fonctionnement de cet outil peuvent provoquer des blessures permanentes aux doigts, aux mains

et aux bras. Utiliser des gants pour amortir davantage les vibrations, prendre de fréquentes pério-

des de repos et limiter la durée quotidienne d’utilisation.

• Le ponçage de peinture à base de plomb, de bois traité chimiquement (sous pression)

ou tout autre matériau contenant des éléments cancérogènes n’est pas recommandé. Le

ponçage de ces matériaux ne doit être réalisé que par un professionnel.

• Nettoyer l’outil régulièrement, particulièrement après une utilisation intensive. La poussière

et les saletés contenant des particules métalliques s’accumulent souvent sur les surfaces internes

de l’outil et pourraient constituer un risque de blessure grave, de choc électrique ou d’électrocu-

tion. Toujours Toujours porter des débrancher la ponceuse avant de procéder au nettoyage.

lunettes de sécurité en conformité avec la norme ANSI Z87.1.

• TOUJOURS débrancher l’outil avant de changer de feuilles abrasives. Ces mesures préventi-

ves réduisent les risques de démarrage accidentel de l’outil électrique.

• Remplacer un disque de système de finition contrôlé usé lorsqu’il provoque une augmentation

trop élevée du régime de l’outil. Un régime trop élevé attribuable à un disque usé peut provoquer

la séparation du patin de la ponceuse et causer des blessures. Pour obtenir des directives rela-

tives au remplacement d’un disque de système de finition contrôlé, consulter la section du présent

manuel intitulée « Entretien de l’outil ».

RALLONGE

Pour la sécurité de l’utilisateur, utiliser une rallonge de calibre adéquat (AWG, American Wire

Gauge [calibrage américain normalisé des fils]). Plus le numéro de calibre de fil est petit et plus sa

capacité est grande, par exemple un calibre 16 a plus de capacité qu’un calibre 18. L’usage d’une ral-

longe de calibre insuffisant causera une chute de tension entraînant perte de puissance et surchauffe.

Si plus d’une rallonge est utilisée pour obtenir la longueur totale, s’assurer que chaque rallonge pré-

sente au moins le calibre de fil minimum. Le tableau ci-dessous illustre les calibres à utiliser selon la

longueur de rallonge et l’intensité nominale indiquée sur la plaque signalétique. En cas de doutes,

utiliser le calibre suivant. Plus le calibre est petit, plus la rallonge peut supporter de courant.

Calibre minimum pour rallonge

Intensité nominale

Volts Longueur totale du cordon

en mètres (en pieds)

120V 7,6 (25) 15,2 (50) 30,5 (100) 45,7 (150)

240V 15,2 (50) 30,5 (100) 61,0 (200) 91,4 (300)

Plus de Pas plus de AWG

0 6 5,5 (18) 4,9 (16) 4,9 (16) 4,3 (14)

6 10 5,5 (18) 4,9 (16) 4,3 (14) 3,7 (12)

10 12 4,9 (16) 4,9 (16) 4,3 (14) 3,7 (12)

12 16 4,3 (14) 3,7 (12) Non recommandé

Porter systématiquement une protection oculaire. Tout utilisateur ou individu

présent doit porter une protection oculaire homologuée ANSI Z87.1.

Pendant l’utilisation, porter systématiquement une protection auditive individuelle

adéquate homologuée ANSI S12.6 (S3.19). Sous certaines conditions et suivant la longueur

d’utilisation, le bruit émanant de ce produit pourrait contribuer à une perte de l’acuité auditive.

TOUJOURS porter des lunettes de sécurité. Les lunettes ordinaires ne

constituent PAS des lunettes de sécurité. Utiliser également un masque protecteur ou antipoussière si

l’opération de coupe génère de la poussière. TOUJOURS PORTER UN ÉQUIPEMENT DE SÉCURITÉ

HOMOLOGUÉ :

• protection oculaire conforme à la norme ANSI Z87.1 (CAN/CSA Z94.3),

• protection auditive conforme à la norme ANSI S12.6 (S3.19) et

• protection des voies respiratoires conforme aux normes NIOSH/OSHA/MSHA.

Produktspezifikationen

Marke:	Porter-Cable
Kategorie:	Schleifmaschine
Modell:	382

Brauchst du Hilfe?

Wenn Sie Hilfe mit Porter-Cable 382 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Schleifmaschine Porter-Cable

Porter-Cable PCEG011 Bedienungsanleitung

14 August 2024

Porter-Cable 382 Bedienungsanleitung

8 Mai 2023

Porter-Cable 380 Bedienungsanleitung

8 Mai 2023

Porter-Cable 7345 Bedienungsanleitung

8 Mai 2023

Porter-Cable 352VS Bedienungsanleitung

8 Mai 2023

Porter-Cable 7800 Bedienungsanleitung

21 Oktober 2022

Bedienungsanleitung Schleifmaschine

Neueste Bedienungsanleitung für -Kategorien-

Makita GA9060R Bedienungsanleitung

15 Oktober 2024

Hitachi G 13SR Bedienungsanleitung

14 Oktober 2024

Makita DGA700Z Bedienungsanleitung

13 Oktober 2024

Metabo WP820-115 Bedienungsanleitung

8 Oktober 2024

DeWalt DW887N Bedienungsanleitung

7 Oktober 2024

Milwaukee 0725-21 Bedienungsanleitung

5 Oktober 2024

Makita GA013GD101 Bedienungsanleitung

3 Oktober 2024

Milwaukee 2784-20 Bedienungsanleitung

3 Oktober 2024

Ryobi RAG800-115 Bedienungsanleitung

2 Oktober 2024

Makita GA022GD202 Bedienungsanleitung

2 Oktober 2024