Pioneer DJM-700-S Bedienungsanleitung

Pioneer Mischer DJM-700-S

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pioneer DJM-700-S (80 Seiten) in der Kategorie Mischer. Dieser Bedienungsanleitung war für 50 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/80

DJ MIXER

MESA DE MEZCLAS DJ

DJM-700-S

DJM-700-K

Operating Instructions

Manual de instrucciones

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product's

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_En-A

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified

service personnel.

D3-4-2-1-2-2_B_En

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the

fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug

must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of

safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows ;

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter or coloured BLACK.N

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter or coloured RED.L

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

D8-10-1-2_En

CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the

unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and

televisions, use shielded cables and connectors for connections.

D8-10-3a_En

Information to User

Alteration or modifications carried out without

appropriate authorization may invalidate the user’s

right to operate the equipment.

D8-10-2_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left

unused for a long period of time (for example, when

on vacation). D3-4-2-2-1a_A_En

CAUTION

The POWER switch on this unit will not completely

shut off all power from the AC outlet. Since the

power cord serves as the main disconnect device for

the unit, you will need to unplug it from the AC outlet

to shut down all power. Therefore, make sure the

unit has been installed so that the power cord can

be easily unplugged from the AC outlet in case of an

accident. To avoid fire hazard, the power cord should

also be unplugged from the AC outlet when left

unused for a long period of time (for example, when

on vacation). D3-4-2-2-2a_A_En

WARNING

This equipment is not waterproof. To prevent a fire

or shock hazard, do not place any container filed

with liquid near this equipment (such as a vase or

flower pot) or expose it to dripping, splashing, rain

or moisture. D3-4-2-1-3_A_En

WARNING

To prevent a fire hazard, do not place any naked

flame sources (such as a lighted candle) on the

equipment. D3-4-2-1-7a_A_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat

radiation (at least 5 cm at rear, and 3 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the

product, and to protect it from overheating. To

prevent fire hazard, the openings should never be

blocked or covered with items (such as newspapers,

table-cloths, curtains) or by operating the

equipment on thick carpet or a bed.

D3-4-2-1-7b_A_En

Operating Environment

Operating environment temperature and humidity:

+5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light) D3-4-2-1-7c_A_En

WARNING

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230V

or 120V) written on the bottom panel.

D3-4-2-1-4_A_En

mod

Before plugging in for the first time, read the following

section carefully.

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized

service center or your dealer for a replacement. S002_En

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading

the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory

drawings. However the method of connecting and operating the unit is the same. K015 En

When using this product follow the instructions

written on the underside of the unit, which

concern rated voltage, etc. D3-4-2-2-4_En

English

LINE VOLTAGE SELECTOR SWITCH

The line voltage selector switch is located on the side panel of this

mixier.The factory setting for the voltage selector is 220-240V.

Check that it is set properly before plugging the power cord into

the outlet. If the voltage is not properly set or if you move to an area

where the voltage requirements differ, adjust the selector switch

as follows:

• Use a medium-sized (flat blade) screwdriver. Insert the tip of the

screwdriver into the groove of the selector switch and set it so

that the power voltage marking of your area points to the arrow.

• For Taiwan, please set to 110-120V before using.

Contents

CONFIRM ACCESSORIES..............................................4

CAUTIONS REGARDING HANDLING............................4

Location .......................................................................................... 4

Cleaning the Unit........................................................................... 4

FEATURES ....................................................................4

CONNECTIONS .............................................................5

CONNECTION PANEL ................................................................... 5

CONNECTING INPUTS.................................................................. 6

CONNECTING EXTERNAL EFFECTORS, OUTPUT

CONNECTORS............................................................................... 7

ABOUT MIDI CONNECTORS........................................................ 8

CONNECTING MICROPHONE AND HEADPHONES ................. 8

CONNECTING THE POWER CORD.............................................. 8

NAMES AND FUNCTIONS OF PARTS ...........................9

MIXER OPERATIONS..................................................13

FADER START FUNCTION .......................................................... 14

EFFECT FUNCTIONS ...................................................16

PRODUCING BEAT EFFECTS...................................................... 18

MANUAL FILTER OPERATION.................................................... 19

EFFECT FREQUENCY FILTER OPERATION................................ 19

EFFECT PARAMETERS................................................................ 20

MIDI SETTINGS ..........................................................21

SYNCHRONIZING AUDIO SIGNALS TO EXTERNAL

SEQUENCER, OR USING DJM-700-S/DJM-700-K INFORMATION

TO OPERATE AN EXTERNAL SEQUENCER .............................. 21

MIDI MESSAGES ......................................................................... 22

PROGRAM CHANGE ................................................................... 24

SNAPSHOT................................................................................... 24

MIDI ON/OFF................................................................................ 24

TROUBLESHOOTING ..................................................25

SPECIFICATIONS........................................................26

110-120V 220-240V

VOLTAGE

SELECTOR

Produktspezifikationen

Marke:	Pioneer
Kategorie:	Mischer
Modell:	DJM-700-S
Gewicht:	6600 g
AUX-Eingang:	Ja
Anzahl USB 2.0 Anschlüsse:	2
Stromverbrauch (Standardbetrieb):	33 W
Anzahl Kanäle:	4 Kanäle
THD, totalklirren:	0.005 %
Digital Audio-Ausgang (koaxial):	1
Frequenzbereich:	20 - 20000 Hz
Mikrofon-Eingang:	Ja
Abmessungen (BxTxH):	320 x 107.9 x 378.4 mm
Digital sound Bearbeitung:	24 Bit
Samplerate:	96 kHz
Phono-Eingänge (RCA):	3
Line-Eingänge (RCA):	5
Übersprechen (1 kHz):	82 dB
Mikrofon Signal-to-Noise Ratio (SNR):	82 dB
Master (L, R) Ausgang:	1
Linie Signal-zu-Laut Ratio (SNR):	104 dB
Booth-Out (1/4"):	1
Master (XLR) Ausgang:	1
Anzahl der EQ bands pro Kanal:	3