Pioneer CDJ-400 Bedienungsanleitung

Pioneer DJ Ausrüstung CDJ-400

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pioneer CDJ-400 (69 Seiten) in der Kategorie DJ Ausrüstung. Dieser Bedienungsanleitung war für 35 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/69

COMPACT DISC PLAYER

LECTEUR DE COMPACT DISC

COMPACT-DISC-SPIELER

LETTORE DI COMPACT DISC

COMPACT DISC-SPELER

REPRODUCTOR DE DISCOS COMPACTOS

ПРОИГРЫВАТЕЛЬ КОМПАКТ-ДИСКОВ

CDJ-400

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Istruzioni per l’uso

Handleiding

Manual de instrucciones

Инструкции по эксплуатации

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product's

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_En-A

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified

service personnel.

D3-4-2-1-2-2_B_En

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the

fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug

must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of

safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows ;

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter or coloured BLACK.N

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter or coloured RED.L

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

CAUTION

This product is a class 1 laser product, but this

product contains a laser diode higher than Class 1.

To ensure continued safety, do not remove any covers

or attempt to gain access to the inside of the product.

Refer all servicing to qualified personnel.

The following caution label appears on your unit.

Location: Inside of the player

CLASS 1

LASER PRODUCT

APPAREIL Á LASER

DE CLASSE 1

D3-4-2-1-8_B_En

CAUTION

ATTENTION

CLASS 3B INVISIBLE LASER RADIATION

WHEN OPEN, AVOID EXPOSURE TO BEAM.

RADIATIONS LASER INVISIBLES DE CLASSE 3B QUAND

OUVERT. ÉVITEZ TOUT EXPOSITION AU FAISCEAU.

ADVARSEL

KLASSE 3B USYNLIG LASERSTRÅLING VED ÅBNING.

UNDGÅ UDSÆTTELSE FOR STRÅLING.

VARNING

KLASS 3B OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD. UNDVIK ATT UTSÄTTA DIG FÖR STRÅLEN.

VARO!

AVATTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE

LUOKAN 3B LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

PRECAUCIAÓN

CUANDO SE ABRE HAY RADIACIÓN LÁSER DE CLASE 3B

INVISIBLE. EVITE LA EXPOSICIÓN A LOS RAYOS LÁSER.

VORSICHT

BEI GEÖFFNETER ABDECKUNG IST UNSICHTBARE LASERSTRAHLUNG

DER KLASSE 3B IM GERÄTEINNEREN VORHANDEN. NICHT DEM

LASERSTRAHLAUSSETZEN!

DRW2308-A

WARNING

This equipment is not waterproof. To prevent a fire

or shock hazard, do not place any container filled

with liquid near this equipment (such as a vase or

flower pot) or expose it to dripping, splashing, rain

or moisture. D3-4-2-1-3_A_En

WARNING

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230V

or 120V) written on the rear panel.

D3-4-2-1-4_A_En

Before plugging in for the first time, read the following

section carefully.

WARNING

To prevent a fire hazard, do not place any naked

flame sources (such as a lighted candle) on the

equipment.

D3-4-2-1-7a_A_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat

radiation (at least 5 cm at rear, and 5 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the

product, and to protect it from overheating. To

prevent fire hazard, the openings should never be

blocked or covered with items (such as newspapers,

table-cloths, curtains) or by operating the

equipment on thick carpet or a bed.

D3-4-2-1-7b_A_En

Operating Environment

Operating environment temperature and humidity:

+5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c_A_En

This product complies with the Low Voltage Directive

2006/95/EC and EMC Directive 2004/108/EC.

D3-4-2-1-9a_A_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left

unused for a long period of time (for example, when

on vacation).

D3-4-2-2-1a_A_En

CAUTION

The POWER switch on this unit will not completely

shut off all power from the AC outlet. Since the

power cord serves as the main disconnect device for

the unit, you will need to unplug it from the AC outlet

to shut down all power. Therefore, make sure the

unit has been installed so that the power cord can

be easily unplugged from the AC outlet in case of an

accident. To avoid fire hazard, the power cord should

also be unplugged from the AC outlet when left

unused for a long period of time (for example, when

on vacation).

D3-4-2-2-2a_A_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized

service center or your dealer for a replacement.

S002_En

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading

the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory

drawings. However the method of connecting and operating the unit is the same.

K015 En

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used

electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to

designated collection facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential

negative effects on the environment and human health. K058_A_En

When using this product follow the instructions

written on the underside of the unit, which

concern rated voltage, etc.

D3-4-2-2-4_En

BEFORE OPERATING (FEATURES)

English

FEATURES

Designed for professional use by DJs, the CDJ-400 compact

disc player provides all the functions and performance re-

quired in disco clubs while offering performance, sound qua-

lity and functionality superior to analog players.

SCRATCH JOG EFFECT

Equipped with Scratch Jog Effect for new scratch sounds.

Equipped with three buttons [BUBBLE], [TRANS] and [WAH]

for new scratch sounds. Effects that are different from the nor-

mal scratch sound can be obtained, broadening the possibili-

ties of your DJ play.

DIGITAL JOG BREAK

Equipped with Digital Jog Break for original sound effects.

Individual remix assist functions [JET], [ROLL] and [WAH]

have been provided individually in three buttons. By choosing

a function and operating the jog dial in time with the music, a

new remix world can be experienced.

JOG DIAL

The large 115 mm diameter jog dial enables better handling

than an analog turntable.

■ PITCH BEND

This function changes the music tempo depending on the di-

rection and speed the jog dial is rotated.

■ SCRATCH PLAY

In the VINYL mode when the surface of the jog dial is pressed

playback is discontinued and then continues according to the

direction and speed the dial is rotated.

■ FRAME SEARCH

Moves the pause position in frame units (1/75 sec) when the

jog dial is rotated in the pause mode.

■ SUPER-FAST SEARCH

By turning the jog dial while holding down the manual search

button or the track search button, disc search can be per-

formed faster than normal search or track search functions.

TEMPO CONTROL

100 mm long high-precision slider allowing free speed adjust-

ment.

With a digital display calibrated in 0.02 % units (within a ±6 %

range), tempo adjustments can be made more easily and ac-

curately.

■ TEMPO CONTROL RANGE

The maximum variable range can be set to four variable

ranges; ±6 %, ±10 %, ±16 %, WIDE, to provide easier operation

environment.

■ MASTER TEMPO

Maintains the same pitch of sound while changing the music

tempo.

REVERSE PLAY

When the reverse button (DIRECTION REV) is pressed so that

the button’s indicator lamp lights, play is performed in the re-

verse direction.

CUE

■ BACK CUE

After storing cue points in memory, press the buttonCUE

while playing a track to return and start from the stored cue

point.

■ AUTO CUE

Skips the non-recorded part at the top of a track and automati-

cally enters stand-by mode at the track’s starting point, allow-

ing playback to begin instantly when the buttonPLAY/PAUSE

(6) is pressed.

■ CUE POINT SAMPLER

Playback can be started at one touch from a stored cue point,

convenient for confirming start points and as sampler.

CUE/LOOP MEMORY

This player is equipped with an internal memory that permits

the recording of cue point or loop point; the recorded points

can later be recalled as desired.

REAL TIME SEAMLESS LOOP

This function simplifies the setting and canceling of loops.

The loop can be set at the very instant the track is being

played. By setting a loop just before the end of the track, the

track can be made so that it doesn’t stop. In addition, an

ADJUST mode has been added to enable one-touch adjust-

ments to the loop-out point, thereby facilitating the loop op-

eration.

RELOOP

Allows returning to the set loop position any number of times.

Press the button after canceling loop play toRELOOP/EXIT

return to the loop start position. By using the loop ON and OFF

combined with the rhythm of the track, new sound effects can

be created.

BEAT LOOP/LOOP DIVIDE

Automatically sets a loop-out point according to the track’s

BPM and starts loop-play. Each additional time the button is

pressed, the loop is divided and a new rhythm produced.

PLAYING ADDRESS

The bar graph provides a visual reference of the track play-

back progress that enables the user to visualize the current

playback position, in the same way as is done with an analog

record by checking the position of the needle. The current po-

sition can be confirmed by the length of the graph, and in ad-

dition, the graph flashes to notify the ending of the track.

FADER START

When a Pioneer DJ mixer (sold separately) is connected, the

mixer’s fader operation can be used to perform quick start

and back cue.

RELAY PLAY

Two CDJ-400 units can be connected in tandem to perform

automatic relay play.

When track playback stops on one of the players, the standby

mode of the other player is released and playback begins au-

tomatically.

Produktspezifikationen

Marke:	Pioneer
Kategorie:	DJ Ausrüstung
Modell:	CDJ-400
Gewicht:	2700 g
Playback MP3:	Ja
Stromverbrauch (Standardbetrieb):	19 W
Gerätetyp:	Tragbarer CD-Player
THD, totalklirren:	0.006 %
Energiebedarf:	220 - 240 V, 50/60 Hz
Rauschverhältnis (SNR):	115 dB
Frequenzbereich:	4 - 20000 Hz
Abmessungen (BxTxH):	217.9 x 296.3 x 107.5 mm
CD-R-Wiedergabe:	Ja
CD-RW-Wiedergabe:	Ja
Unterstützte Medientypen:	CD, CD-R, CD-RW, MP3 CD
Audioausgang:	1x RCA, DIGITAL