Pelco IMEEBAP-I Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Pelco IMEEBAP-I (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
1
I E -I ME BAP and
IMEEBAP-E
Electrical Box
Adapter & Type 4X
Adapter
Installation Manual
2
Important Notices
For more information about Pelco’s product-specific important notices and thereto related information, refer to
www.pelco.com/legal.
REGULATORY NOTICES
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Radio and Television Interference
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can
void yo ur authority to operate this equipment under Federal Communications Commission’s rules.
CAN ICES-3(A)/NMB-3(A).
KOREAN CLASS A EMC
WARRANTY STATEMENT
For information about Pelco’s product warranty and thereto related information, refer to www.pelco .com/
warranty.
UL Safety Notices
This product is intended to be supplied by a Listed Power Unit marked “L.P.S.” (or “Limited Power Source”)
and rate output 24Vac, 50/60Hz, 1.28 minimum or 48 Vdc, 0.35A minimum.
The product shall be installed by a qualified service person and the installation shall conform to local codes.
3
Electrical Box Adapter & Type 4X Mount Environmental (IMEEBAP-E: )
and Type 4S Adapter Indoor (IMEEBAP- I)
Installation Guide
NOTE: The environmental camera is weather tight, rated IP66 if installed directly to a surface. So, this mounting
plate is optional. However, to comply with Type 4X outdoor rating, one must install the Type 4X mounting plate.
(The Type 4X plate has a dual function to mount to junction boxes, so you can ignore the additional holes if not
installing to a junction box.)
1. Install the Type 4X electrical adapter plate on the surface or Type 4X electrical box and secure the
screws.
2. Prepare the wire entry holes through the plate and camera box as follows:
a. Remove the conduit plug if required and move to the hole not used.
3. Remove the dome cover from the camera (optional).
4. Install the camera to the plate.
5. Pull the wire through the conduit hole into the camera.
6. Mount the plate/camera to the surface . using the holes marked “A” in the illustration above
7. Connect and seal the conduit.
8. Adjust the angle of lens by pan and tilt by the base.
9. Tighten the locking screw to secure the camera module position.
BASE
A


Produktspezifikationen

Marke: Pelco
Kategorie: Nicht kategorisiert
Modell: IMEEBAP-I

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pelco IMEEBAP-I benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Pelco

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-