Ozito RHD-900 Bedienungsanleitung

Ozito bohren RHD-900

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ozito RHD-900 (6 Seiten) in der Kategorie bohren. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
ROTARY
HAMMER
DRILL KIT
900W
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 900W
Impact Rate: 4,100 bpm
Impact Energy: 3.0 Joule
No Load Speed: 850/min
Accessory Fitment: SDS+
Drilling Capacities: Masonry 26mm
RHD-900
WHAT’S IN THE BOX
Kit Box
Rotary Hammer Drill
Side Handle
Accessories
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the original
date of purchase and it is intended for DIY (Do It Yourself) use only.
If a product is defective it will be replaced in accordance with the
terms of this warranty. Warranty excludes consumable parts, for example:
carbon brushes, included accessories etc.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other than that
specied on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights
and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You
are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount
to a major failure.
Generally you will be responsible for all costs associated with a claim
under this warranty, however, where you have suffered any additional
direct loss as a result of a defective product you may be able to claim
such expenses by contacting our customer service helpline above.
ozito.com.au
0517
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
KNOW YOUR PRODUCT
1. USING THE DEPTH ROD
The depth rod allows you to drill to a predetermined depth.
1 SDS+ Accessory Holder
2 Accessory Locking Sleeve
3 Depth Rod Locking Hole
4 Side Handle
5 Side Mode Selector
6 Grease Cap
7 Rear Mode Selector
8 On/Off Switch
9 Rear Handle
ROTARY HAMMER DRILL
10 Depth Rod
11 3 x SDS+ 150mm Drill Bits
12 1 x SDS+ Flat Chisel
14 x 250mm
13 1 x SDS+ Point Chisel
14 x 250mm
14 Dust Cover
15 Tub of Grease
16 Pin Spanner
ACCESSORIES
SETUP & PREPARATION
WARNING! ENSURE THE TOOL IS DISCONNECTED
FROM THE POWER SUPPLY BEFORE PERFORMING
ANY OF THE FOLLOWING OPERATIONS.
Required
Drilling
Depth
1 Loosen the depth rod
securing nut then insert
depth rod.
4 Drill the hole until
the end of the
depth rod touches
the workpiece.
3 Tighten the depth
rod securing nut to
lock the depth rod
into place.
2 Adjust the depth
rod so the drill bit
extends beyond the
end of the depth
rod to the required
drilling depth.
1
10 12 13 14 15 1611
2 3 4 5 6 7 8 9
2. SDS+ ACCESSORIES 3.
FITTING AND USING THE DUST COVER
1 Prior to insertion into
chuck, ensure the SDS
+
accessory is clear of
dust and debris.
1 Slide dust cover over
accessory.
3 Insert drill bit in locking
sleeve.
4 Press dust cover to the
end of locking sleeve.
2 Add lubrication grease.
3 Pull locking sleeve back
and hold.
5 Rotate and continue to
insert as far as possible.
7 Checked SDS+ accessory
is locked. Try to pull it out.
Note: It should have approx
10 – 20mm movement. This
is normal.
2 Prior to insertion into
drill add supplied
lubricant to the SDS
+
accessory.
4 Insert SDS+ Accessory.
6 Release locking sleeve.
8 To remove the SDS+
accessory pull back the
locking sleeve and pull
accessory out.
a
b
Accessory
SDS+
The cover catches dust and debris - while using the drill upright or
overhead - to avoid dust entering the air vents.


Produktspezifikationen

Marke: Ozito
Kategorie: bohren
Modell: RHD-900

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ozito RHD-900 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung bohren Ozito

Bedienungsanleitung bohren

Neueste Bedienungsanleitung fĂźr -Kategorien-