Ozito BDP-500 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ozito BDP-500 (8 Seiten) in der Kategorie bohren. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8
DRILL
PRESS
500W 9 Speed
INSTRUCTION MANUAL
BDP -500
STANDARD EQUIPMENT
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself) use
only. If a product is defective it will be replaced in accordance with
the terms of this warranty. Warranty excludes consumable parts, for
example: feed wheel handles, keyed chuck, hex key, chuck key, belt.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction
manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
0719
SPECIFICATIONS
Motor Size: 500W (S2 15min)
Input: 230 – 240V ~ 50Hz
No Load Speed: 500-2,500/min
Chuck: 16mm Keyed
Morse Taper: B16-2MT
Spindle Travel: 50mm
Spindle Shaft to
Column Distance: 115mm
Column Height: 625mm
Table Size: 168x168mm
Table Tilt: 0-45
0 (Left & Right)
Weight: 16.08kg
3
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Assembling the drill press
1. Carefully remove contents from the packaging.
2. Select a rm, level surface on which
to assemble the drill press.
3. Place the base and align the column
over the large hole. Align the holes
in the column support with those
in the base and secure in place
using the 3 column support bolts
(supplied). Using a 14mm spanner
securely tighten all
3 column support bolts.
4. Slide the table support over the
column. Using the table support
lock, secure the table into the
desired position.
5. Lift the head assembly and slide it
down onto the column as far as it
will go. Rotate the head so that is
aligned with the base.
To secure in position install the 2
head lock screws. Tighten using
the 4mm Hex key, rotating in a
clockwise direction.
DRILL PRESS
KNOW YOUR PRODUCT
2120
1. ASSEMBLY
SETUP & PREPARATION
WARNING! DURING ASSEMBLY ENSURE THE
DRILL PRESS IS DISCONNECTED FROM THE
POWER SUPPLY.
ACCESSORIES
20. Chuck key
21. 4mm & 10mm
Hex key
1. Emergency Stop Button
2. Pulley cover screw
3. Feed wheel handles
4. Belt tension knob
5. Feed wheel hub
6. Column
7. 16mm Keyed chuck
8. Eye Shield
9. Table
10. Table support
11. Table support lock
12. Column support bolts x 3
13. Column support
14. Base
15. Head assembly
16. Depth indicator
17. ON/OFF Switch
18. Head lock screw
19. Chuck Key Holder
1
2
4
3
5
6
7
10
11
13
14
15
9
12
17
18
8
16
19
6. To t the eye shield, rst loosen the
phillips head screw on the shield
and then slide over the drill spindle.
Tighten the securing screw to lock
in position.
7. To t the feed wheel handles,
screw them into the feed
wheel hub.
8. To t the keyed chuck, rst place
a piece of timber on the table and
position the keyed chuck with the
jaws retracted under the drive
shaft. Raise the table toward
the drive shaft until the chuck is
approximately 25mm from the
drive shaft.
9. To secure the keyed chuck to the drive
shaft gently lower the drive shaft using
the feed wheel handles until the drive
shaft is pushed into the rear of the keyed
chuck. A gentle tap on the timber is
required to secure the keyed chuck onto
the tapered drive shaft.
Installing and removing drill bits
1. Using the chuck key, loosen the
jaws of the chuck by rotating in an
anti-clockwise direction.
2. Insert the drill bit fully into the
keyed chuck.
3. Whilst holding the drill bit in one
hand, rotate the top collar of
the keyed chuck in a clockwise
direction.
Ensure that you tighten all 3 holes
in the keyed chuck using the chuck
key to securely tighten the jaws and
hold the drill bit in position.
Approx. 25mm
Produktspezifikationen
| Marke: | Ozito |
| Kategorie: | bohren |
| Modell: | BDP-500 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Ozito BDP-500 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung bohren Ozito
16 Oktober 2024
23 August 2024
19 August 2024
16 August 2024
15 August 2024
14 August 2024
9 August 2024
8 August 2024
8 August 2024
8 August 2024
Bedienungsanleitung bohren
- bohren Basetech
- bohren Panasonic
- bohren Clas Ohlson
- bohren Cotech
- bohren Makita
- bohren Bosch
- bohren Flex
- bohren Laserliner
- bohren Parkside
- bohren Vonroc
- bohren AEG
- bohren Velleman
- bohren Powerfix
- bohren Black And Decker
- bohren Cocraft
- bohren FERM
- bohren Ryobi
- bohren Skil
- bohren Topcraft
- bohren Trotec
- bohren Maestro
- bohren Baier
- bohren Carat
- bohren Eibenstock
- bohren Hilti
- bohren Bort
- bohren DeWalt
- bohren Einhell
- bohren Elu
- bohren Festool
- bohren Mafell
- bohren Maktec
- bohren Worx
- bohren Luxor
- bohren Hikoki
- bohren Hitachi
- bohren Hyundai
- bohren Hazet
- bohren Kinzo
- bohren Kress
- bohren Max
- bohren Metabo
- bohren Stanley
- bohren Würth
- bohren Güde
- bohren Power Craft
- bohren Scheppach
- bohren Workzone
- bohren Biltema
- bohren Meec Tools
- bohren Dremel
- bohren Fieldmann
- bohren EcoMAC
- bohren Proxxon
- bohren Westfalia
- bohren Dedra
- bohren DURO
- bohren Graphite
- bohren Silverline
- bohren Holzmann
- bohren MSW
- bohren Huvema
- bohren Robust
- bohren Zipper
- bohren Stomer
- bohren Yato
- bohren Baumr-AG
- bohren Genesis
- bohren BluCave
- bohren Toolland
- bohren Delta
- bohren Batavia
- bohren Bavaria
- bohren Brüder Mannesmann
- bohren Milwaukee
- bohren Narex
- bohren Toolcraft
- bohren Fein
- bohren Verto
- bohren Craftsman
- bohren Powerplus
- bohren Rupes
- bohren ProfiTech
- bohren Alpha Tools
- bohren Kawasaki
- bohren Sun Joe
- bohren Ridgid
- bohren Porter-Cable
- bohren VARO
- bohren Duro Pro
- bohren Economy
- bohren Fe Powertools
- bohren Gamma
- bohren Global
- bohren Goon
- bohren Lux Tools
- bohren Max Bahr
- bohren Protool
- bohren Spit
- bohren Steren
- bohren Tanaka
- bohren Meister Craft
- bohren Malmbergs
- bohren Truper
- bohren RIKON
- bohren Kreg
- bohren G-Technology
- bohren Einhell Bavaria
- bohren Powerblade
- bohren Rok
- bohren Tryton
- bohren MyTool
- bohren McKenzie
- bohren Rodcraft
- bohren Ribimex
- bohren Black Decker
- bohren RUKO
- bohren Handwerk
- bohren Stalco
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024