Ozito CDL-1810U Bedienungsanleitung
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Ozito CDL-1810U (3 Seiten) in der Kategorie bohren. Dieser Bedienungsanleitung war fĂĽr 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/3
CORDLESS
DRILL
DRIVER
18V Lithium Ion
ORIGINAL INSTRUCTIONS
SPECIFICATIONS
Input: 18V
Chuck Size: 10mm Keyless
No Load Speed: 0-550/min
Torque Setting: 21
Max. Torque: 16Nm
Battery Power: 1.5Ah Lithium Ion
Charge time: 3-5 Hours
Weight: 0.9kg
CDL-1810U
WHAT’S IN THE BOX
Cordless Drill Driver
MAINTENANCE
DESCRIPTION OF SYMBOLS
TROUBLESHOOTING
WARNING! Wear ear protectors when impact drilling Exposure to noise can
cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause
personal injury.
Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
Before drilling into walls, ceilings etc, ensure that there are no concealed power cables
or pipes in the cavity.
WARNING! Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contain chemicals known to cause
cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products
• Arsenic and chromium from chemically treated timber
Your risk from exposure to these chemicals varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well ventilated
area and work with approved safety equipment, such as dust masks that are specially
designed to îšżlter out microscopic particles.
This appliance is not intended for use by young or inîšżrm persons unless
supervised by a responsible person to ensure that they can use the appliance
safely. Young children should be supervised to ensure that they do not play with the
appliance.
1. When not in use, the drill should be stored in a dry, frost free
location, keep out of children’s reach.
2. Keep ventilation slots of the drill clean at all times and prevent
anything from entering.
3. If the housing of the drill requires cleaning, do not use solvents.
Use of a cloth only is recommended.
4. Blow out the ventilation slots with compressed air periodically .
Note: Ozito Industries will not be responsible for any damage or
injuries caused by repair of the drill by an unauthorised person or by
mishandling.
SPARE PARTS
ozito-diy.co.uk
DRILL DRIVER SAFETY WARNINGS
18V Battery
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, îšżre and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodiîšżed plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your îšżnger on
the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger speciîšżed by the manufacturer. A charger that is suitable for one
type of battery pack may create a risk of îšżre when used with another batery pack.
b. Use power tools only with speciîšżcally designated battery packs. Use of any other battery packs may
create a risk of injury and îšżre.
c. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a îšżre.
d. Under abusive conditions, liquid may be ejected from the battery; aviod contact. If contact
accidentally occurs, ush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritationor burns.
6. Service
a. Have your power tool serviced by a qualiîšżed repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
GENERAL POWER TOOL SAFETY WARNINGS
ELECTRICAL SAFETY
BATTERY AND CHARGER SAFETY WARNINGS
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR
YOUR BATTERY CHARGER.
1. Before using the charger read all instructions and cautionary markings on the charger, battery
pack and the product using the battery pack.
2. This charger is not intended for any uses other than charging rechargeable batteries. Any other
use may result in risk of îšżre, electric shock or electrocution.
3. Do not place any object on top of the charger or place the charger on a soft surface that may
result in excessive internal heat. Place the charger in a position away from any heat source.
4. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when
disconnecting the charger.
5. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected
to damage or stress.
6. An extension cord should not be used unless absolutely necessary. Use of an improper extension
cord could result in the risk of îšżre, electric shock or electrocution.
7. Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in
any way. Have it checked by an electrician or power tool repairer.
8. Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair
is required. Incorrect reassembly may result in a risk of electric shock, electrocution or îšżre.
9. To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning.
Removing the battery pack will not reduce this risk.
10. Never attempt to connect 2 chargers together.
11. DO NOT store or use the tool and battery pack in locations where the temperature may reach or
exceed 40ÂşC (such as inside sheds or metal buildings in summer).
12. The charger is designed to operate on standard household electrical power (240 volts). Do not
attempt to use it on any other voltage!
13. The battery pack is not fully charged out of the carton. First read the safety instructions and then
follow the charging notes and procedures.
14. The longest life and best performance can be obtained if the battery pack is charged when the
air temperature is between 18 - 24ÂşC. Do not charge the battery pack in an air temperature below
10ÂşC or above 40ÂşC. This is important and will prevent damage to the battery pack.
15. Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The
battery can explode in a îšżre.
16. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack
breaks or cracks, immediately discontinue use and do not recharge.
17. During charging, the battery must be placed in a well ventilated area.
LED lights do not illuminate on charger
Check the charging adaptor is securely plugged into the wall outlet.
Check the battery is îšżrmly connected to the charging cradle.
Check that the charging jack is securely connected to the charging cradle.
Variable speed trigger is locked
Ensure that the forward / reverse lever is in the correct position; pressed
left for forwards direction, pressed right for backwards direction. If it is in
between the two settings the variable speed trigger will be locked.
The drill is stripping the screw head
Ensure you are starting with a low torque setting and holding the drill
securely onto the screw head. Increase the torque setting as required.
Drill has cut out during use
The battery charge could be completely depleted. Place the battery on the
charging cradle for 3-5 hours.
Sparking visible through the housing air vents
A small amount of sparking may be visible through the housing vents.
This is normal and does not indicate a problem.
Charging Adaptor & Cradle
Belt Clip
WARNING! When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of îšżre, electric shock, personal injury and
material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before
operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The manufacturer cannot accept any liability for damage or accidents which arise due to a failure to follow these
instructions and the safety information.
Before you connect the equipment to the mains supply make sure that the data on the rating plate are identical
to the mains data.
This charger is double insulated therefore no earth wire is required.
The power supply for this product should be protected by a residual current device (rated at 30mA or less). A
residual current device reduces the risk of electric shock.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualiîšżed
persons in order to avoid a hazard.
Note: Double insulation does not take the place of normal safety precautions when operating this tool. The
insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not
suitable for the power input of the tool or which is damaged or defective may result in a risk of îšżre and electric
shock.
WARRANTY
OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG 0616
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the customer
service number shown. Please note the following terms under which
guarantee claims can be made:
1. These warranty terms regulate additional warranty services, which the
manufacturer mentioned below promises to buyers of its new products
in addition to their statutory guarantee claims are not affected by this
guarantee. Our guarantee is free of charge to you.
2. The warranty services only covers defects due to material or
manufacturing faults on a product which you have bought from the
manufacturer mentioned below are limited to either the rectiîšżcation of said
defects on the product or the replacement of the product, whichever we
prefer.
Please note that our devices are not designed for use in commercial, trade
or professional applications. A guarantee contract will not be created if the
device has been used by commercial, trade or industrial business or has
been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly
instructions or due to incorrect installation, a failure to follow the operating
instructions (for example connecting it to an incorrect mains voltage or
current type) or a failure to follow the maintenance and safety instructions
or by exposing the device to abnormal environmental conditions or by lack
of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example
overloading the device or the use or unapproved tools or accessories),
ingress of foreign bodies into the device (such as sand, stones or dust,
transport damage), the use of force or damage caused by external forces
(for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural
wear or tear or by normal use of the device.
4. Your Product is guaranteed for a period of 36 months from the original
date of purchase and is intended for DIY (Do It Yourself) use only. Lithium
Ion batteries and chargers are covered by a 12 month warranty. Warranty
excludes consumable parts. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect
being noticed. No guarantee claims will be accepted after the end of the
guarantee period. The original guarantee period remains applicable to the
device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts îšżtted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work
performed or parts îšżtted. This also applies if an on-site service is used.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR
REGISTER RECEIPT.
Please refer to the restrictions of this warranty concerning wearing parts,
consumables and missing parts as set out in the service information in
these operating instructions.
CUSTOMER SERVICE HELPLINE
GB: 0151 294 4488
IRL: 1850 882711
Ozito-diy.co.uk
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse or Homebase store.
For further information, or any parts visit
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: enquires@ozito-diy.co.uk
Warning Read instruction manual
ø Diameter
mA Milliamperes
Recycle battery Do not put in the rubbish
Polarity
Do not incinerate Do not get battery wet
Thermal cut-out protection
Double insulated
/min Revolutions or
reciprocation per minute
Ah Amp hour
Indoor use only
Lithium Ion battery Do not use or store battery in
temperatures exceeding 50ÂşC
IPM Impacts per minute Nm Newton Meters
no No load speed
V Volts Hz Hertz
ac/~ Alternating current W ttsWa
Direct current
dc/
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
FWD
KNOW YOUR PRODUCT SETUP & PREPARATION
CDL-1810U
1. BATTERY 2. KEYLESS CHUCK 3. CONTROLS 4. DRILLING 5.
HELPFUL TIPS
1 Keyless Chuck
2 Torque Adjustment Collar
3 LED Light
4 Variable Speed Trigger
5 Battery Release Button
6 Battery 18V
7 Forward/ Reverse Lever
CORDLESS DRILL DRIVER
OPERATION
1 2 3 4 5
8
6
9
7
10
When drilling hard, smooth surfaces, use a centre punch to mark
the desired hole location. This measure will prevent the drill bit from
slipping off centre as you start the hole.
When drilling metals, use light oil on the drill bit to keep it from
overheating. The oil will prolong the life of the bit and increase drilling
action.
8 Charging Cradle
9 Charging Adaptor
10 Charging Jack
11 Belt Clip
Charging
Forward/ Reverse Lever Before starting to drill, perform a few simple checks.
Adjusting Torque
Variable Speed Trigger
Installing the Battery Pack
1 Plug charging jack into
charging cradle. The green
light only will illuminate when
connected.
1 For forward rotation, push the fwd/rev lever towards the left side of
the drill. For reverse rotation push fwd/rev lever to the right.
1 Slide the battery into the drill base until it clicks into place.
3 Secure the material to be drilled in a vice or clamp to stop it turning
whilst drilling.
3 Drill into the material until the surface reaches the start of the tape..
7 Move the drill bit into the workpiece.
1 Rotate the torque collar to the desired setting.
1 To start drilling squeeze the
variable speed trigger.
1 Depress and release the
variable speed trigger to
ensure it is not locked on. 1 Measure along the drill bit to
indicate the desired depth
5 Hold the drill îšżrmly and place
the bit at the point to be drilled.
2 Slide the battery onto the
charging cradle. Both lights
will illuminate when battery is
properly connected.
2 To stop drilling release the
trigger.
2 Check the forward/reverse
lever is on desired setting.
2 Wrap a small piece of masking
tape tightly around the drill bit.
6 Depress the variable speed
trigger to start the drill.
FWD
Note: Once fully charged, the green light only will be illuminated.
Installing a Drill Bit
Removing the Battery Pack
Removing a Drill Bit
1 Rotate the chuck collar anti-
clockwise to open the chuck
1 Hold down the battery release
button.
1 Open the chuck by rotating the
chuck collar and remove the
frill bit.
3 Tighten the chuck by turning
clockwise.
2 Insert the drill bit,
making sure it
is centred in the
chuck.
2 Slide the battery
out.
4 Pull on the bit to
ensure it is îšżrmly
secured.
Note: The more the variable speed trigger is depressed, the
faster the drill bit will rotate.
Note: Do not force the drill or apply side pressure to elongate
the hole. Let the drill do all the work.
Note: Selecting a higher torque setting will allow the drill to
use more torque to drive the screw in or out. To prevent
damaging the screw head, it is recommended to start at
a low torque setting and increase when necessary.
Torque Settings
Drilling to a Preset Depth
2 If the clutch rachets and
makes a clicking sound before
screw is ush, increase the
collar setting and continue
tightening.
Torque settings can alter the depth to which you can drill or drive into
a surface. To determine the torque setting required to drive a screw
perfectly ush to the work surface, follow the below steps.
A simple way of achieving a hole at a desired depth is to use masking
tape.
1 Set the torque
collar to lowest
setting and tighten
the îšżrst screw.
3 Repeat until you
reach the correct
setting/ screw
depth. Use this
setting for the
remaining screws.
CAUTION: TO REDUCE THE RISK OF INJURY WE
RECOMMEND THE USE OF GLOVES WHEN HANDLING
DRILL BITS.
WARNING! THE POWER SUPPLY FOR THIS CHARGER
SHOULD BE PROTECTED BY A RESIDUAL CURRENT
DEVICE (RATED AT 30MA OR LESS). A RESIDUAL CURRENT
DEVICE REDUCES THE RISK OF ELECTRIC SHOCK.
WARNING! Ensure the tool is turned off & disconnected from the
power supply before performing any of the following operations.
11
ACCESSORIES
Produktspezifikationen
| Marke: | Ozito |
| Kategorie: | bohren |
| Modell: | CDL-1810U |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Ozito CDL-1810U benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung bohren Ozito
16 Oktober 2024
23 August 2024
19 August 2024
16 August 2024
15 August 2024
14 August 2024
9 August 2024
8 August 2024
8 August 2024
8 August 2024
Bedienungsanleitung bohren
- bohren Basetech
- bohren Panasonic
- bohren Clas Ohlson
- bohren Cotech
- bohren Makita
- bohren Bosch
- bohren Flex
- bohren Laserliner
- bohren Parkside
- bohren Vonroc
- bohren AEG
- bohren Velleman
- bohren Powerfix
- bohren Black And Decker
- bohren Cocraft
- bohren FERM
- bohren Ryobi
- bohren Skil
- bohren Topcraft
- bohren Trotec
- bohren Maestro
- bohren Baier
- bohren Carat
- bohren Eibenstock
- bohren Hilti
- bohren Bort
- bohren DeWalt
- bohren Einhell
- bohren Elu
- bohren Festool
- bohren Mafell
- bohren Maktec
- bohren Worx
- bohren Luxor
- bohren Hikoki
- bohren Hitachi
- bohren Hyundai
- bohren Hazet
- bohren Kinzo
- bohren Kress
- bohren Max
- bohren Metabo
- bohren Stanley
- bohren WĂĽrth
- bohren GĂĽde
- bohren Power Craft
- bohren Scheppach
- bohren Workzone
- bohren Biltema
- bohren Meec Tools
- bohren Dremel
- bohren Fieldmann
- bohren EcoMAC
- bohren Proxxon
- bohren Westfalia
- bohren Dedra
- bohren DURO
- bohren Graphite
- bohren Silverline
- bohren Holzmann
- bohren MSW
- bohren Huvema
- bohren Robust
- bohren Zipper
- bohren Stomer
- bohren Yato
- bohren Baumr-AG
- bohren Genesis
- bohren BluCave
- bohren Toolland
- bohren Delta
- bohren Batavia
- bohren Bavaria
- bohren BrĂĽder Mannesmann
- bohren Milwaukee
- bohren Narex
- bohren Toolcraft
- bohren Fein
- bohren Verto
- bohren Craftsman
- bohren Powerplus
- bohren Rupes
- bohren ProfiTech
- bohren Alpha Tools
- bohren Kawasaki
- bohren Sun Joe
- bohren Ridgid
- bohren Porter-Cable
- bohren VARO
- bohren Duro Pro
- bohren Economy
- bohren Fe Powertools
- bohren Gamma
- bohren Global
- bohren Goon
- bohren Lux Tools
- bohren Max Bahr
- bohren Protool
- bohren Spit
- bohren Steren
- bohren Tanaka
- bohren Meister Craft
- bohren Malmbergs
- bohren Truper
- bohren RIKON
- bohren Kreg
- bohren G-Technology
- bohren Einhell Bavaria
- bohren Powerblade
- bohren Rok
- bohren Tryton
- bohren MyTool
- bohren McKenzie
- bohren Rodcraft
- bohren Ribimex
- bohren Black Decker
- bohren RUKO
- bohren Handwerk
- bohren Stalco
Neueste Bedienungsanleitung fĂĽr -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024