Ozito QSS-1000U Bedienungsanleitung

Ozito Sander QSS-1000U

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ozito QSS-1000U (2 Seiten) in der Kategorie Sander. Dieser Bedienungsanleitung war für 23 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

• Keep the vents of the sander clean at all times. If possible, prevent foreign

matter from entering the vents.

• After each use, blow air through the sander housing to ensure it is free from

all dust particles which may build up. Build up of dust particles may cause the

sander to overheat and fail.

• If the enclosure of the sander requires cleaning, do not use solvents but a

moist soft cloth only. Never let any liquid get inside the sander; never immerse

any part of the sander into a liquid.

Carbon Brushes

When the carbon brushes wear out, the sander

will spark and/or stop. Discontinue use as soon

as this happens. They should be replaced prior to

recommencing use of the sander. Carbon brushes

are a wearing component of the sander and are

therefore not covered under warranty. Continuing

to use the sander when carbon brushes need to

be replaced may cause permanent damage to the

sander. Carbon brushes will wear out after many uses. When the carbon

brushes need to be replaced, take the sander to an electrician or a power tool

repairer for a quick and low cost replacement. Always replace both carbon

brushes at the same time.

Note: Ozito Industries will not be responsible for any damage or injuries

caused by the repair of the sander by an unauthorised person or by

mishandling of the sander.

ORBITAL

SANDER

1/4 SHEET

ORIGINAL INSTRUCTIONS

SPECIFICATIONS

Voltage: 230-240V ~ 50Hz

Power: 135W

No Load Spead: 13,000/min

Pad Shape: 1/4 Sheet

Pad Size: (110x100mm)

Weight: 0.9kg

WHAT’S IN THE BOX

Quarter Sheet Sander

Sand Paper x 3

Dust Bag

MAINTENANCE

DESCRIPTION OF SYMBOLS

TROUBLE SHOOTING

V Hz

~ W

/bpm

/min

Volts

Alternating current

Revolutions or

reciprocation per minute

Orbital per minute

Double insulated

Warning

Hertz

Watts

No load speed

Diameter

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents.

This is normal and does not indicate a problem.

Excessive sparking visible through the housing air vents

and/or the drill failing to operate

May indicate the carbon brushes have worn out and need to be replaced. Carbon

brushes should only be replaced by a qualied electrician or power tool repairer.

Sandpaper Selection

Selecting the correct grit of sandpaper is an important step in achieving

optimum results. Coarse grit will remove the most material. Finer grit will

produce a smoother nish. The condition of the workpiece will determine the

grit of the sandpaper to be used. The higher the grit number, the ner the

grade of sandpaper.

If the surface is rough, start with a coarse grit and sand until the surface is

uniform. Medium grit may then be used to remove scratches left by the coarser

grit. Finer grit is then used to nish the surface. Always continue sanding with

each grade of sandpaper until the surface is uniform.

MATERIAL APPROPRIATE GRIT

Coarse Sanding Fine Sanding

Paintwork 180 400

Wood: Softwood 60 240

Hardwood 60 180

Veneer 240 320

Note: If intermediate sanding is required, choose a grit rating between coarse and

ne. The above table is intended as a guide only. To ensure a satisfactory result,

a small, inconspicuous area should rst be tested to ensure the grit of sandpaper

chosen is suitable for the desired nish.

Sanding Tips

Never force the sander. The weight of the sander supplies adequate pressure,

allowing the sandpaper to do the work. Applying additional pressure will slow the

motor, rapidly wear the sandpaper, and greatly reduce the sander speed. This will

slow the removal rate and produce an inferior quality surface.

CAUTION: Excessive pressure will overload the motor, causing possible damage

to the sander by overheating the motor; or damage to the workpiece.

Be sure to check your workpiece often. The sander is capable of removing

material rapidly, especially with coarse paper.

The orbital action of your sander allows you to sand with the grain, or at any angle

across it for most sanding jobs. In the nal stages a better nish will be achieved

by sanding with the grain.

Do not sand on one spot for too long. The sander’s rapid action may remove too

much material, creating an uneven surface.

SPARE PARTS

ozito-diy.co.uk

QUARTER SHEET SANDER SAFETY WARNINGS

Read Instruction Manual

Paper Punch Plate

QSS-1000U

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of re, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool o󰀨 in an emergency, before

operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the equipment to the mains supply make sure that the data on the rating plate are

identical to the mains data.

This tool is double insulated therefore no earth wire is required.

If the supply cord of this power tool is damaged, it must be replaced by a specially prepared cord available

through the service organization.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The

insulation system is for added protection against injury resulting from a possible electrical insulation failure

within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the

extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not

suitable for the power input of the tool or which is damaged or defective may result in a risk of re and electric

shock.

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

WARNING!

• This tool may only be used for dry grinding/sanding operations.

• Always guide the power cable away from the back of the tool.

• Use of the tool on materials containing asbestos is prohibited.

• Always remove the plug from the power supply socket before carrying out any work

on the machine (cleaning the sander, changing the sandpaper, etc.).

• Always disconnect the machine by removing the plug from the socket, not by pulling

on the power cable.

• To protect your health, always wear safety goggles and a dust mask during sanding/

grinding work!

• Keep your workplace clean and well illuminated.

• Make sure that the workpiece is su󰀩ciently secured so that it cannot slip.

• Keep children away.

• For your own sake, keep the machine clean at all times and check it for signs of

damage each time after using it.

• Make sure that the switch is set to OFF before you insert the plug into the power

supply socket.

• Make sure of your footing, particularly when working on ladders and platforms.

• Harmful or toxic dust can be produced when working on wood or metal.

Touching or inhaling this dust can be harmful for the operator and other persons

nearby.

• If you discover any damage to the machine, use the exploded diagram and the

spare parts list to determine which parts need to be ordered from Customer Service.

• Important! Wear safety goggles and a dust mask.

Do not lose these safety instructions.

Spare parts can be ordered from the Special Orders Desk

at your local Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: enquires@ozito-diy.co.uk

WARRANTY

iSC GmbH · Eschenstraße 6 · 94405 Landau /Isar · Germany 0716

All of our products undergo strict quality checks to ensure that they reach

you in perfect condition. In the unlikely event that your device develops a

fault, please contact our service department at the address shown on this

guarantee card. You can also contact us by telephone using the customer

service number shown. Please note the following terms under which

guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the

manufacturer mentioned below promises to buyers of its new products

in addition to their statutory guarantee claims are not a󰀨ected by this

guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or

manufacturing faults on a product which you have bought from the

manufacturer mentioned below are limited to either the rectication of said

defects on the product or the replacement of the product, whichever we

prefer.

Please note that our devices are not designed for use in commercial, trade

or professional applications. A guarantee contract will not be created if the

device has been used by commercial, trade or industrial business or has

been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly

instructions or due to incorrect installation, a failure to follow the operating

instructions (for example connecting it to an incorrect mains voltage or

current type) or a failure to follow the maintenance and safety instructions

or by exposing the device to abnormal environmental conditions or by lack

of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example

overloading the device or the use or unapproved tools or accessories),

ingress of foreign bodies into the device (such as sand, stones or dust,

transport damage), the use of force or damage caused by external forces

(for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural

wear or tear or by normal use of the device.

4. Your Product is guaranteed for a period of 36 months from the original

date of purchase and is intended for DIY (Do It Yourself) use only. Lithium

Ion batteries and chargers are covered by a 12 month warranty. Warranty

excludes consumable parts. Guarantee claims should be submitted

before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the

guarantee period. The original guarantee period remains applicable to the

device even if repairs are carried out or parts are replaced. In such cases,

the work performed or parts tted will not result in an extension of the

guarantee period, and no new guarantee will become active for the work

performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST

RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR

Please refer to the restrictions of this warranty concerning wearing parts,

consumables and missing parts as set out in the service information in

these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

WARNING! Read all the safety information, instructions, illustrations and technical data

provided on or with this power tool. Failure to adhere to the following instructions may result in

electric shock, re and/or serious injury.

Keep all the safety information and instructions in a safe place for future use.

The term „power tool“ used in the safety information and instructions refers to power tools operated

from the mains power supply (with a power cable) and to battery operated power tools (without a

power cable).

1. Workplace safety

a) Keep your work area clean and well lit. Untidy or unlit work areas can result in accidents.

b) Do not use this power tool in an area where there is a risk of explosion and where there are

inammable liquids, gases or dust. Power tools generate sparks that can ignite dust or vapors.

c) Keep children and other people away from the power tool while you are using it. If you are

distracted you may lose control of the power tool.

2. Electrical safety

a) The plug on the power tool must t into the socket. The socket must not be modied in any way. Do

not use adapter plugs together with power tools with a protective earth. Unmodied plugs and matching

sockets will reduce the risk of an electric shock.

b) Avoid body contact with earthed surfaces such as pipes, heating systems, stoves and

refrigerators. There is an increased risk of su󰀨ering an electric shock if your body is earthed.

c) Keep the power tool out of the rain and away from moisture. The ingress of water into an electric

power tool increases the risk of an electric shock.

d) Do not use the power cable for a purpose for which it is not designed, for example to carry the

power tool, hang it up or to pull the plug out of the socket. Keep the power cable away from heat,

oil, sharp edges and moving parts. Power cables that are damaged or tangled increase the risk of an

electric shock.

e) If you use an electric power tool outdoors, use only extension cables that are suitable for outdoor

use. The use of an extension cable which is suitable for outdoor use reduces the risk of an electric

shock.

f) If you cannot avoid using the power tool in a damp location, use a residual current device

(RCD) circuit breaker. The use of a residual current device (RCD) circuit breaker will reduce the risk of

su󰀨ering an electric shock.

3. Safety of persons

a) Be careful, watch what you are doing and be sensible and responsible when using an electric

power tool. Never use the power tool if you are tired or under the inuence of drugs, alcohol or

medication. One moment of inattention when using the electric tool can result in serious injuries.

b) Wear personal safety equipment and always wear safety goggles. Wearing personal safety

equipment such as dust masks, non-slip safety shoes, a helmet or ear plugs, depending on the type and

application of the tool, reduces the risk of injury.

c) Make sure that the tool cannot start up accidentally. Ensure that the power tool is switched o󰀨 before

you connect it to the power supply and/or connect the battery pack, pick it up or carry it. If you have your

nger on the switch while carrying the power tool or if you connect the power tool to the power supply

while it is switched on, this may cause accidents.

d) Remove all adjusting tools or wrenches before you switch on the power tool. Any tool or wrench in

a rotating part of the power tool could cause injuries.

e) Avoid abnormal working postures. Make sure you stand squarely and keep your balance at all times.

This will enable you to control the power tool better in unexpected situations.

f) Wear suitable clothes. Never wear loose tting clothes or jewelry. Keep hair and clothing away from

moving parts. Loose clothing, jewelry or long hair can be caught by moving parts.

g) If dust extraction devices and dust collection devices can be tted, they must be connected and

must be used correctly. The use of a dust extractor can reduce the dangers posed by dust.

h) Do not allow yourself to be lulled into a false sense of security and do not ignore the safety

regulations covering electric power tools, even if you are familiar with the power tool after having

used it many times. Carelessness can lead to serious injuries in just a fraction of a second.

4. Using and handling the power tool

a) Do not overload your power tool. Use the correct electric tool for the job in hand. The correct tool will

enable you to work better and more safely within the specic performance range.

b) Do not use an electric power tool if the switch is defective. An electric power tool that cannot be

switched on or o󰀨 is dangerous and must be repaired.

c) Pull the plug out of the socket and/or remove the removable battery pack before making any

adjustments to the tool, changing plug-in tool parts or putting the power tool down. These

precautions will prevent the power tool starting accidentally.

d) Keep unused electric tools out of the reach of children. Do not allow people who are not familiar

with the power tool or who have not read these instructions to use the power tool. Electric tools are

dangerous if they are used by inexperienced people.

e) Look after power tools and plug-in tools with care. Check that moving parts function correctly and do

not jam, and whether any parts are broken or damaged such that they adversely a󰀨ect the function of the

power tool. Have damaged parts repaired before you use the power tool. Many accidents are caused by

poorly maintained electric tools.

f) Keep cutting tools sharp and clean. Carefully maintained cutting tools with sharp cutting edges will

jam less and are easier to control.

g) Use the power tool, plug-in tools, etc. as set out in these instructions. Take account of the

conditions in your work area and the job in hand. Using electric tools for purposes other than the one for

which they are designed can result in dangerous situations.

h) Keep the handles and grip surfaces dry, clean and free from oil and grease. If the handles and grip

surfaces are slippery, it will not be possible to operate and control the power tool safely in unforeseen

situations.

5. Service

a) Have your power tool repaired only by trained personnel using only genuine spare parts. This will

ensure that your power tool remains safe to use.

Anleitung_QSS_1000U.indd 1-3

Anleitung_QSS_1000U.indd 1-3Anleitung_QSS_1000U.indd 1-3 11.12.2019 15:21:41

11.12.2019 15:21:41

11.12.2019 15:21:4111.12.2019 15:21:41

KNOW YOUR PRODUCT

1. SANDING SHEET FITMENT 3. DUST BAG 4. ON/OFF SWITCH 5.

SANDING

2. To turn the sander o󰀨, press the on/o󰀨 button again.

5. Dust Bag

6. Hook & Loop Sanding Sheet

7. Paper Punch Plate

ACCESSORIES

1 On/O󰀨 Switch

2 Hook & Loop Backing Pad

3 Sure Grip Handle

4 Spring Clamp

QUARTER SHEET SANDER

SETUP & PREPARATION OPERATION

1/3

The tool is recommended for use with a residual current

device with a rated residual current of 30mA or less.

2. To turn the sander on, press the on/o󰀨 switch.

QSS-1000U

2. PAPER PUNCH PLATE

2. Align the sides of the backing pad with the raised sides of the

punch. Press down to punch the holes.

1. Fit the 1/4 sanding sheet to the sander.

1. When tting the sanding sheet, align the holes on the sheet with

the holes on the sanding pad.

Use the punch to create dust extraction holes on the sandpaper

which align with the holes on the sander.

Ensure the tool is disconnected from the power supply

before performing any of the following operations.

1. Connect the tool to the mains power supply.

CAUTION: GUIDE THE CORD DURING SANDING TO

PREVENT IT BEING CAUGHT ON THE WORKPIECE,

OR OTHER OBJECTS.

1. Secure the material to be sanded.

2. Firmly grasp the sander. Turn it on and let the motor build up to

maximum speed. Gradually lower it onto the workpiece using a

forward movement.

3. For optimum results, use backward and forward strokes.

The holes on the bottom of the sanding pad allow the dust bag to

draw the sanding dust away from the work area.

3. Fold the sandpaper to

match the contours of

the sanding pad.

2. Unlock the spring clamp

on both sides of the

sander.

5. Feed the paper under

the clamp at the rear

of the sander. Lock the

clamp.

4. Feed the paper under

the clamp at the front

of the sander. Lock the

clamp.

Note: Ensure the sanding sheet is rmly clamped and held at

against the base of the sanding pad.

2. To remove, rotate

and pull the dust

bag away from the

extraction port.

1. Push the dust

bag onto the dust

extraction port

aligning the locking

tab and rotate.

Install

3. Empty dust bag when it becomes

1/3 full for optimum dust

extraction.

Remove

Empty

Note: Keep the entire sanding pad in contact with the workpiece at

all times during sanding.

Anleitung_QSS_1000U.indd 4-6

Anleitung_QSS_1000U.indd 4-6Anleitung_QSS_1000U.indd 4-6 11.12.2019 15:21:42

11.12.2019 15:21:42

11.12.2019 15:21:4211.12.2019 15:21:42

Produktspezifikationen

Marke:	Ozito
Kategorie:	Sander
Modell:	QSS-1000U

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ozito QSS-1000U benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Sander Ozito

Ozito TSS-3100U Bedienungsanleitung

18 August 2024

Ozito HSS-5000U Bedienungsanleitung

16 August 2024

Ozito QSS-1000U Bedienungsanleitung

15 August 2024

Ozito ROS-2000U Bedienungsanleitung

15 August 2024

Ozito ROS-4000U Bedienungsanleitung

15 August 2024

Ozito DSR-2100U Bedienungsanleitung

12 August 2024

Ozito PXROS-125U Bedienungsanleitung

10 August 2024

Ozito OZBG150WAU Bedienungsanleitung

9 August 2024

Ozito DSR-2000 Bedienungsanleitung

24 Juli 2024

Ozito PXBPS-254 Bedienungsanleitung

21 Juli 2024

Bedienungsanleitung Sander

Neueste Bedienungsanleitung für -Kategorien-

Hilti DWS 225 Bedienungsanleitung

15 Oktober 2024

Matrix BS 600 Bedienungsanleitung

8 Oktober 2024

Black And Decker RO410 Bedienungsanleitung

7 Oktober 2024

Black And Decker BT300 Bedienungsanleitung

5 Oktober 2024

Gamma HS200W Bedienungsanleitung

5 Oktober 2024

Gamma IB-350W Bedienungsanleitung

4 Oktober 2024

Gamma HPS-200W Bedienungsanleitung

4 Oktober 2024

Black And Decker FS1000 Bedienungsanleitung

4 Oktober 2024

Powerplus POWE40010 Bedienungsanleitung

3 Oktober 2024

Hazet 9032 MK Bedienungsanleitung

1 Oktober 2024