Ozito OZCCS85WA Bedienungsanleitung
Ozito
Sägemaschine
OZCCS85WA
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr Ozito OZCCS85WA (8 Seiten) in der Kategorie Sägemaschine. Dieser Bedienungsanleitung war fĂźr 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8

CHAINSAW
CHAIN
SHARPENER
85W
INSTRUCTION MANUAL
OZCCS85WA
WHATâS IN THE BOX
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: wheel.
WARNING
The following actions will result in the warranty being void.
â˘î If the tool has been operated on a supply voltage other
thanîthatîspeciîˇedîonîtheîtool.
â˘î If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
â˘î Failure to perform maintenance as set out within the
instruction manual.
â˘î If the tool is disassembled or tampered with in any way.
â˘î Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/NewîZealandî(HeadîOfîˇce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
Theîbeneîˇtsîprovidedîunderîthisîwarrantyîareîinîadditionî
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
1014
SPECIFICATIONS
Motor: 85W
Input: 230V-240V ~ 50Hz
No load speed: 4,800/min
Table/vice angles: 0 â 35° left & right
Sharpening Wheel: Ă108 x 3.2mm
Bore: Ă23mm
Suits chain pitch: 0.325â and 3/8â
Weight: 2.4kg
Chainsaw Chain Sharpener
Sharpening Wheel
(assembled)
Table & Lock Knob

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Assembling the table
1. Insert the bolt of the table through
the hole in the base.
2. Secure the table in place by îżxing
the locking knob to the bolt (by
screwing the knob clockwise).
Mounting the sharpener
For safe operation of the sharpener, the base of the tool must be îżtted to
a îat, solid, secure surface such as a work bench.
The sharpener base is designed in two halves. The rear half is for îżtting
îat to a stable surface and the front is designed to protrude over the edge
of the mounting surface.
The sharpener base should
be îżtted to the mounting
surface by sliding the
rear half back until the
two âstepsâ on the base
align with the edge of the
mounting surface. Ensure
when mounting, that the
table locking knob is still
easily accessible for when
adjusting the table angles.
Two 6mm mounting holes allow for îżxing
the base to the mounting surface (bolts
not supplied). Ensure the mounting
surface is capable of supporting the
weight of the sharpener and chain to
be sharpened.
1. Lowering hand piece
2. Sharpening wheel cover
3. Direction of rotation indicator
4. Safety guard
5. Sharpening wheel
6. Depth of grind knob
7. Depth of grind locking knob
8. Depth of grind pin
9. Guide clamp lever
10. Chain (tooth) stop
11. Guide
12 Depth stop platform
13. Table locking knob
14 Bench mounting holes
15. Sharpener base
16. Chain stop adjusting
knob lock nut
17. Adjustable table
18. Chain stop adjusting knob
19. Table scale
CHAINSAW CHAIN SHARPENER
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
6
2
16
7
4
17
3
18
8
9 10 11
13
12
14 15
19
WARNING!: BEFORE ASSEMBLING, MOUNTING,
SETTING OR MAINTAINING YOUR SHARPENER,
MAKE SURE THAT THE MOTOR IS OFF AND THE TOOL
DISCONNECTED FROM THE POWER SUPPLY TO PREVENT
ACCIDENTAL STARTING.
1
5

4. If you do not know the angle of the chain
set, the table angle to 35°.
Take hold of the hand piece and bring it
down so that the wheel is slowly lowered
into the chain, along the cutting tooth.
Slowly move the table so the cutting face
of the tooth is parallel with the edge of the
wheel. The most common chain angles
are 30 35°. It may be necessary to slide â
the chain slightly to allow the wheel to
enter down the face of the tooth.
5. Once the correct angle as been achieved
tighten the table locking knob to lock the
table in the current position.
After the table is locked in the required
position, take hold of the hand piece and
lower the head assembly until the wheel
is aligned along the tooth of the chain.
Conîżrm the angle then slide the chain so
the face of the tooth is just touching the
face of the wheel.
6. Lock the guide by rotating
the clamping lever as far
as it will go in a clockwise
direction. Ensure the chain
is clamped îżrmly into the
sliding guide. Should the
chain still not be clamped,
pull the clamping lever
outwards (away from the
guide), turn the lever anti-
clockwise 1/4 of a turn.
Push the lever back in towards the guide.
Proceed to rotate the lever fully clockwise.
Check the chain is clamped. Should it
still not be clamped, repeat the process
above.
2. SETTING OF THE SHARPENER
Note. Prior to using the sharpener, several adjustments must be made in
order to sharpen the teeth of the chain effectively.
1. Adjusting the angle of cut.
2. Adjusting the chain (tooth) stop.
3. Adjusting the depth of cut.
Failure to perform these adjustments will result in poor sharpening and
possible damage to the chain being sharpened.
Before making adjustments, always ensure the sharpener has been
disconnected from the power supply.
Adjusting the angle of cut
1. Open the slide guide groove
by rotating the guide clamp
lever anti-clockwise.
2. Fit a chain over the guide groove
ensuring the inner side of the chain
sits inside the guide groove. Ensure
the chain hangs freely over the side
of the mounting surface. The chain
should be îżtted so the teeth face the
right hand side of the sharpener and
the chain can move freely in both
directions.
3. If you know the angle of the chain,
rotate the table to the same angle as
the chain. To rotate the table loosen
the table lock knob and rotate the
table until the scale indicator lines
up with the scale on the base of the
sharpener.
Produktspezifikationen
Marke: | Ozito |
Kategorie: | Sägemaschine |
Modell: | OZCCS85WA |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Ozito OZCCS85WA benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Sägemaschine Ozito

6 September 2024

6 September 2024

6 September 2024

5 September 2024

5 September 2024

18 August 2024

17 August 2024

16 August 2024

16 August 2024

14 August 2024
Bedienungsanleitung Sägemaschine
- Sägemaschine Brennenstuhl
- Sägemaschine Cotech
- Sägemaschine Makita
- Sägemaschine Royal Catering
- Sägemaschine Bosch
- Sägemaschine Flex
- Sägemaschine Parkside
- Sägemaschine Vonroc
- Sägemaschine AEG
- Sägemaschine Black And Decker
- Sägemaschine Cocraft
- Sägemaschine FERM
- Sägemaschine Ryobi
- Sägemaschine Skil
- Sägemaschine Topcraft
- Sägemaschine Trotec
- Sägemaschine Maestro
- Sägemaschine Prime3
- Sägemaschine Hilti
- Sägemaschine Bort
- Sägemaschine DeWalt
- Sägemaschine Einhell
- Sägemaschine Elu
- Sägemaschine Festool
- Sägemaschine Mafell
- Sägemaschine Maktec
- Sägemaschine Worx
- Sägemaschine Luxor
- Sägemaschine Tacklife
- Sägemaschine Hikoki
- Sägemaschine Hitachi
- Sägemaschine Hyundai
- Sägemaschine Fuxtec
- Sägemaschine Kress
- Sägemaschine Max
- Sägemaschine Metabo
- Sägemaschine Stanley
- Sägemaschine Atika
- Sägemaschine Gßde
- Sägemaschine Power Craft
- Sägemaschine Scheppach
- Sägemaschine Workzone
- Sägemaschine Biltema
- Sägemaschine Meec Tools
- Sägemaschine Dremel
- Sägemaschine Fieldmann
- Sägemaschine King Craft
- Sägemaschine Proxxon
- Sägemaschine Westfalia
- Sägemaschine Remington
- Sägemaschine Husqvarna
- Sägemaschine Stihl
- Sägemaschine Dedra
- Sägemaschine DURO
- Sägemaschine Graphite
- Sägemaschine Pattfield
- Sägemaschine Silverline
- Sägemaschine Holzmann
- Sägemaschine MSW
- Sägemaschine Florabest
- Sägemaschine Germania
- Sägemaschine Stiga
- Sägemaschine Hammer
- Sägemaschine ACG
- Sägemaschine Greenworks
- Sägemaschine Huvema
- Sägemaschine Robust
- Sägemaschine Zipper
- Sägemaschine Yato
- Sägemaschine Baumr-AG
- Sägemaschine Genesis
- Sägemaschine BluCave
- Sägemaschine Morrison
- Sägemaschine Batavia
- Sägemaschine Evolution
- Sägemaschine Matrix
- Sägemaschine Dolmar
- Sägemaschine Bavaria
- Sägemaschine Brßder Mannesmann
- Sägemaschine Milwaukee
- Sägemaschine Narex
- Sägemaschine Toolcraft
- Sägemaschine Fein
- Sägemaschine AL-KO
- Sägemaschine EGO
- Sägemaschine CMI
- Sägemaschine IDEAL
- Sägemaschine Cobra
- Sägemaschine Verto
- Sägemaschine Craftsman
- Sägemaschine Powerplus
- Sägemaschine Alpha Tools
- Sägemaschine Echo
- Sägemaschine Elektra Beckum
- Sägemaschine Toledo
- Sägemaschine McCulloch
- Sägemaschine Yard Force
- Sägemaschine Sun Joe
- Sägemaschine Solo
- Sägemaschine Texas
- Sägemaschine Oregon Scientific
- Sägemaschine Ridgid
- Sägemaschine Porter-Cable
- Sägemaschine VARO
- Sägemaschine Spear & Jackson
- Sägemaschine Duro Pro
- Sägemaschine Erbauer
- Sägemaschine Ergofix
- Sägemaschine Exakt
- Sägemaschine Ferrex
- Sägemaschine FOM
- Sägemaschine Gamma
- Sägemaschine Gardenline
- Sägemaschine Global
- Sägemaschine Goon
- Sägemaschine Grizzly
- Sägemaschine Gude Pro
- Sägemaschine HURRICANE
- Sägemaschine Kompernass
- Sägemaschine Lux Tools
- Sägemaschine Max Bahr
- Sägemaschine Maxx
- Sägemaschine Qualcast
- Sägemaschine Tanaka
- Sägemaschine Toolson
- Sägemaschine Troy-Bilt
- Sägemaschine Avantco
- Sägemaschine Wolfcraft
- Sägemaschine Masport
- Sägemaschine Garland
- Sägemaschine Meister Craft
- Sägemaschine Clarke
- Sägemaschine Powerworks
- Sägemaschine Sovereign
- Sägemaschine Challenge
- Sägemaschine Challenge Xtreme
- Sägemaschine Truper
- Sägemaschine Ĺucznik
- Sägemaschine Vulcan
- Sägemaschine MacAllister
- Sägemaschine RIKON
- Sägemaschine Backyard Pro Butcher Series
- Sägemaschine Kreg
- Sägemaschine Jonsered
- Sägemaschine Einhell Bavaria
- Sägemaschine Proviel
- Sägemaschine Budget
- Sägemaschine Tryton
- Sägemaschine MTM
- Sägemaschine EFA
- Sägemaschine MyTool
- Sägemaschine McKenzie
- Sägemaschine Anova
- Sägemaschine Yellow Garden Line
- Sägemaschine Ergotools Pattfield
- Sägemaschine IKRA
- Sägemaschine FIXIT
- Sägemaschine Bestgreen
- Sägemaschine BGU
- Sägemaschine Power Smart
- Sägemaschine Ultranatura
- Sägemaschine TAURUS Titanium
- Sägemaschine Maxbear
- Sägemaschine Extralink
- Sägemaschine Stalco
Neueste Bedienungsanleitung fĂźr -Kategorien-

16 Oktober 2024

16 Oktober 2024

15 Oktober 2024

15 Oktober 2024

15 Oktober 2024

15 Oktober 2024

14 Oktober 2024

12 Oktober 2024

12 Oktober 2024

11 Oktober 2024