Nxg NX-C8.2-P Bedienungsanleitung

Nxg Lautsprecher NX-C8.2-P

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Nxg NX-C8.2-P (2 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
(Continued on reverse)
Where To Place Your In-Ceiling Speakers (Fig. 2)
Placement can make all the difference in how your speakers sound, and how easy they will be to install.
Carefully consider where your speakers should be positioned. For optimum performance, speakers should be
mounted to the left and right of the main listening area and a minimum of 8 to 10 feet apart. Avoid mounting
speakers in stud cavities containing electrical wiring, heating ducts, water pipes, etc. Make sure the ceiling
materials are sturdy enough to support the weight of the speakers. Optimum performance will be achieved
when your speakers are mounted to the left and right of the main listening area.
Pivoting Tweeters (Fig. 3)
The tweeters in all NXG Pro Series speakers may be adjusted, allowing you to focus the speakers’ high
frequency output to better fit the listening area. The overall smoothest response is achieved with the tweeter
facing straight out: however, you may find the sound more pleasing by aiming tweeters toward a particular lis-
tening area. To adjust the tweeter, apply pressure on the ring surrounding the tweeter with your thumb or
finger.
Tweeter Level Adjustments (Fig. 4)
The tweeter level control allows you to tailor the speakers’ frequency response to better match the room’s
acoustics. As an example, if a room has a hardwood floor, which makes it acoustically brighter sounding,
you may want to adjust the tweeter level down to compensate. You can experiment to find the sound that’s
most pleasing to you in your particular listening environment.
Speaker Installation In Existing Construction (See Fig. 5 on reverse)
Once you have selected the location for your speakers, you are ready to install them.
You will need the following:
• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers
• Utility Knife or Drywall Saw • Small LevelPencil •
• Masking Tape • Phillips Screwdriver • Speaker Wire
NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer or custom
audio contractor.
1. NXG Architectural Speakers are designed to be installed in the cavities between wall studs. Using a stud
finder, make sure you are between two studs. Using the supplied template and a level to ensure your tem-
plate is straight, tape the template to the wall and lightly trace around the outside with a pencil.
2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of the outline.
This will allow you to check for any obstructions that may exist behind the desired location. CAUTION: Be
certain electrical wiring, water pipes or heating ducts do not interfere in the planned installation areas prior
to drilling or cutting the wall.
3. Run speaker wire from your amplifier or speaker switching device to the speaker location.
4. If you like the standard white finish of your NXG speakers, skip to step 5, but if if you want your
speakers to blend in with a colored wall or ceiling, now is the time to paint your speaker’s outer frame and
perforated grille. The speaker’s outer surface will accept ordinary latex wall paint or aerosol spray paint.
Because the speaker baffle surface behind the grille should remain unpainted, you will need to cover this
area with the supplied paint mask. Cover the speaker’s interior black surface, woofer and tweeter. Paint the
outer speaker frame and grille separately. (Grille painting hint: Use a paint roller that is nearly out of paint
to first paint the inside of the grille, then the outside. This will avoid paint filling the grille perforations.)
5. Attach the wire to the input terminals on the rear of the speaker. Remember to maintain proper polarity
with the amplifier by attaching the positive (+) lead to the red terminal and the negative (-) lead to the black
terminal.
Thank you for choosing NXG Pro Series
Loudspeakers. Like all NXG products, great
care has been taken in their design. Their
combination of advanced engineering and
state-of-the-art materials will provide you
with years of listening pleasure, while blend-
ing smoothly into your home’s decor. Before
you get started, it is a good idea to identify
all the parts and hardware (See Fig. 1).
Speaker with self-contained
mounting clamps
Aluminum grille with
foam inner backing
FIG. 2
NXG Pro Series speakers can be used as
rear surround channels by mounting them
(1) on each side of, (2) just behind,
or (3) in back of the viewing position.
1
1
2
2
3
3
FIG. 3
Adjust tweeter level as shown
Press on the edge of
the tweeter to rotate
FIG. 4
NX-C8.2-P 8˝ Two-Way In-Ceiling Speaker System
FIG. 1
Grille
removal
tool
Black
grille
adhesive
Tweeter Level
Switch
Painting masks
Cutout templates
(Continued from front)
6. See Fig. 6. With the speaker wire attached to the speaker, slide
the speaker up inside the cut-out hole. Center the speaker in the
cut-out hole and turn the four locking screws clockwise until the
speaker is drawn up snugly to the wall board from behind, clamping
the speaker in place. Try to tighten each screw equally. Replace the
speaker grill by gently pressing it into place.
New Construction (A)
Note: Use of optional new construction rough-in bracket kits will
not only save time but will also enhance the sound quality of your
installed speakers. (See rough-in kit installation manual for mounting
instructions when using kits.)
New Construction (B)
(Installation without use of new construction rough-in brackets.)
1. Determine speaker locations and mark them on your plans for
future reference.
2. If possible, run speaker wires after HVAC and electrical wiring is
in place.
3. Secure speaker wires in place along the run with insulated staples
only and be careful not to pierce the wire’s insulation. Allow a bit of
slack for expansion of building materials.
4. Needless to say, the actual speakers should not be installed until
the wall board is in place. In the meantime, leave several feet of wire
coiled up and secured at the back side of the mounting hole.
5. To complete the installation follow steps 2 through 5 above.
FIG. 6
16648 North 94th Street • Scottsdale, AZ 85260
1-800-733-0008 www.nxgtech.com
NXG -YPro Series Three ear Limited Warranty
If the NXG Pro Series speaker system proves to be defective in workmanship or materials within
three years from the date of the original customer’s purchase, we will, at our option, repair or
replace the defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability and fitness for a particular purpose,
are limited in duration to the length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or replacement of the product at our
our option. NXG shall not be liable for incidental or consequential damages of any kind or character
because of product defects. Some states do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations and exclusions may not apply.
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or improper operation.
• Any product whose serial number has been altered, defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage must be made with
the carrier.)
Warranty Service
Warranty service must be performed by an authorized service center, usually an NXG speaker
systems dealer or its authorized agent. You may obtain a list of authorized service centers by con-
tacting NXG. All warranty repairs must be accompanied by the original bill of sales. No other doc-
ument is acceptable or is required. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. NXG reserves the right to revise speaker system
specifications without notice.
Operational Check
After making all connections, it’s a good idea to make sure every-
thing is working properly. Turn on your surround or stereo system,
making sure the volume control is turned down and that the balance
control is in the center position. Activate a musical or movie source
such as FM, a CD or DVD player. Gently turn up the volume, you
should hear sound coming from your new NXG speakers. If no
sound is heard from any or all speakers, switch off the system
immediately and check for open or loose connections, wrong polar-
ity or shorts, or proper source selection.
NX-C8.2-P Specifications
Maximum Power Handling: 5 - 120 watts
Sensitivity: 90dB @ 1 watt/1 meter
Frequency Response: 37 Hz-22,000 Hz
Driver Complement:
8˝ (204 mm) metallic-anodized, graphite-filled, injection-molded RCT
cone woofer with rubber surround
1˝ (25mm) minimum diffraction, pivoting, fluid-cooled, high tenacity
teteron dome tweeter
Impedance: 8 ohms nominal, 6 ohms minimum
Grille: Corrosion-resistant powder coated aluminum
Overall Dimensions (Diameter x Depth): 10 3/4˝ x 4˝ D (273 mm x 102 mm)
Required Ceiling Cutout: 91
/2˝ (241 mm) diameter
FIG. 5

Produktspezifikationen

Marke: Nxg
Kategorie: Lautsprecher
Modell: NX-C8.2-P

Brauchst du Hilfe?

Wenn Sie Hilfe mit Nxg NX-C8.2-P benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Lautsprecher Nxg

Nxg

Nxg NX-W5.2-LCR-P Bedienungsanleitung

21 August 2024
Nxg

Nxg NX-W6.2-P Bedienungsanleitung

21 August 2024
Nxg

Nxg NX-C6.2-P Bedienungsanleitung

20 August 2024
Nxg

Nxg NX-C8.3-P Bedienungsanleitung

19 August 2024
Nxg

Nxg NX-C8.2-P Bedienungsanleitung

18 August 2024
Nxg

Nxg NX-AW5 Bedienungsanleitung

10 Juli 2024
Nxg

Nxg Onyx NX-C8.2-ENC-X Bedienungsanleitung

15 November 2023

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-

Sonance

Sonance Visual Performance VP65 SST Bedienungsanleitung

16 Oktober 2024
Bowers And Wilkins

Bowers And Wilkins CWM664 Bedienungsanleitung

16 Oktober 2024
Focal

Focal Chorus 826 V Bedienungsanleitung

16 Oktober 2024
KEF

KEF Ci200ER Bedienungsanleitung

16 Oktober 2024
Steren

Steren SPK-1100BL Bedienungsanleitung

16 Oktober 2024
Aiwa

Aiwa SP-A100 Bedienungsanleitung

16 Oktober 2024
Trust

Trust GXT 628 Bedienungsanleitung

15 Oktober 2024
Pyle

Pyle PBMSPG6 Bedienungsanleitung

15 Oktober 2024
Marshall

Marshall Tufton Bedienungsanleitung

15 Oktober 2024
Sunstech

Sunstech SPUBT780 Bedienungsanleitung

15 Oktober 2024