Nexa AD-147 Bedienungsanleitung

Nexa Nicht kategorisiert AD-147

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Nexa AD-147 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

AD-147

Plug-in mottagare Dimmer/

Plug-in receiver Dimmer

Svenska

AD-147 är en liten Z-Wave plug-in dimmermottagare som enkelet ansluts

mellan lasten och eluttaget. Den kan styras av Nexa Bridge eller annan

kontroller som är Z-Wavecertierad. AD-147 har en knapp för att kunna slås

av och på utan fjärrkontroll.

Säkerhet

Läs igenom hela instruktionen först.

Anlita fackman vid behov. Nexa kan ej hållas ansvarig om den användas till

annat än den är designad för eller om instruktionen inte följs. Anslut aldrig

lampor eller utrustning som överskrider mottagarens maximala belast-

ning. Det kan leda till fel, kortslutning eller brand. Försök inte att reparera

produkten. Den innehåller inga reparerbara delar. Produkten är inte vattentät.

Se till att den alltid är torr. Använd inte kemikalier, lösningsmedel eller starka

rengöringsmedel. Utsätt inte produkten för stark värme eller kyla.

Teknisk information

Inspänning 230 V ~50 Hz

Last 6-250 W resistiv last

Frekvens Z-Wave (868,42 MHz)

Räckvidd Upp till 30 m

Dimensioner Ø52 x 78 mm

Arbetstemperatursområde -10°C - 40°C

IP klassicering IP20

Installation

Stoppa i plug-in mottagaren i vägguttaget. Stoppa i lastens kontakt i plug-in

mottgaren.

AD-147 kommer ihåg sitt tillstånd om strömmen bryts och sedan kommer

tillbaka (t.ex. vid strömavbrott). Detta kan ändras i Z-Wave-kontrollenheten.

Inkludering i Z-Wave nätverk

På enheten nns en knapp [Link Key] som används för att inkludera, exklu-

dera, och återställa. Se vidare i manualen för Z-Wavekontrollern hur enheten

inkluderas eller exkluderas.

När inget nod-id nns lagrat blinkar LED:en i 0,5 Hz.

Autoinkludering

Om enheten inte har har ett nod-id och spänningssätts så sätts den automa-

tiskt i inkluderingsläge i 4 minuter.

Inkludera Tryck 3 gånger på [Link Key] inom 1,5 sekunder.

Exkludera Tryck 3 gånger på [Link Key] inom 1,5 sekunder.

Återställning Tryck 3 gånger på [Link Key] inom 1,5 sekunder.

Tryck, inom 1 sekund, och håll [Link Key] nedtryckt

tills dess att LED slocknar.

Enheten är nu återställd och ställer sig i autoinklu-

deringsläge.

För information angånde programmering av Z-Wave modulen, se baksidan.

Användning

Styrning med Z-Wavekontroller

Se manualen till din Z-Wavekontroller för information hur du styr din motta-

gare.

Styrning med knappen [Link key]

Tryck en gång för att tända. Tryck igen för att släcka. För att dimra, håll

knappen intryckt när lampan är tänd. Lampan kommer att tändas med den

ljusstyrka den hade när den släcktes.

mer information på:

www.nexa.se/zwave

English

AD-147 is a small Z-Wave plug-in dimmer receiver that easly is connected

between wall socket and load. It can be controlled by Nexa Bridge or other

Z-Wave controller. AD-147 has a button for control without a remote.

Safety

Read the instructions rst.

Call in professional as needed. Nexa can not be held responsible if it is used

for other purposes than it is designed for, or if instructions are not followed.

Never connect the lights or equipment that exceeds the recipient’s maximum

load. It can lead to failure, short circuit or re. Do not attempt to repair the

product. It contains no serviceable parts. The product is not waterproof.

Make sure it is completely dry. Do not use chemicals, solvents or harsh

detergents. Do not expose to extreme heat or cold.

Technical information

Power supply 230 V ~50 Hz

Load 6-250 W resistive load

Frequency Z-Wave (868,42 MHz)

Range Up to 30 m

Dimensions Ø52 x 78 mm

Environment temp. range -10°C - 35°C

IP classication IP20

Installation

Put the plug-in receiver in the wall socket. Put the loads plug in the receiver.

AD-147 is able to remember the status of the relay when power is cut o

(such as power black-out). When power is supplied again, the unit will resu-

me the last status of the relay (on or o) automatically. This can be changed

in the Z-Wave controller.

Adding to a Z-Wave network

The button marked [Link Key] on the unit is used to include, exclude and

reset the unit.

See Z-Wave controller manual how inclusion/exclusion is done.

The Led ashes 0.5 Hz when no Node ID is stored.

Auto inclusion

If the unit has no Node ID and is powered it enters auto inclusion mode for

4 minutes.

Include Press [Link Key] 3 times within 1,5 seconds.

Exclude Press [Link Key] 3 times within 1,5 seconds.

Reset Press [Link Key] 3 times within 1,5 seconds. Then,

within 1 seconds, press and hold [Link Key] until

LED turns o.

The unit is now reset and enters auto inclusion

mode.

For more information regarding how to program the Z-wave unit, see the

other side.

Operation

Operation with Z-Wave controller

See Z-Wave controller’s manual.

Operation with the button [Link key]

Push once to turn on light, push once again to turn o. Push and hold when

light is on to dim. When the light is turned back on, it will have the same light

intensity as it had when turned o.

more information at:

www.nexa.se/zwave

ad147_86802_manual_002 | 1

Z-Wave Group Support

The unit supports two association groups with 1 node support for Grouping 1 and 4 nodes

support for Grouping 2. This has the eect that when the unit is operating, all devices

associated with the unit will receive the relevant reports.

• When the unit is powered up and is already a part of a Z-Wave network, the unit will send

a Notication Report to the node in Group 1.

• When setting the unit or changing the unit’s status, the unit will send a Multilevel Switch

Report to the node of Group 1.

• When performing Reset the unit will send Device Reset Locally Notication to the node

of Group1.

• The minimum interval time between two reports sent from this unit to the node of Group 1

is 3 seconds. Refer to Conguration parameter 2 for more information.

• When the button on the unit or the wall switch (S1) is pressed, the unit will send a Basic

Set command to the nodes of Group 2. When the unit is OFF, Basic Set Value = 0x00.

When the unit is ON, Basic Set Value = 0xFF.

Z-Wave Plus Info

Role Type Node Type Installer Icon User Icon

Slave Always On Z-Wave Plus node Light Dimmer Switch Light Dimmer Switch

Version

Protocol Library 3 (Slave_Enhance_232_Library)

Protocol Version 3.95 ( 6.51.02)

Manufacturer

Manufacturer ID Product Type Product ID

0x0060 0x0003 0x0003

AGI (Association Group Information) Table

Group Prole Command Class & Command (List)

N bytes

Group Name(UTF-8)

1General:NA Multilevel Switch Report,

Notication Report,

Device Reset Locally Notication

Lifeline

2 Basic SetControl:Key1 On/O control

(Button1)

Basic

• Basic Get: Inquire about the status of the device.

• Basic Report: Report the status of the device.

• Basic Set: Set the status of the device.

Basic Set Value Description

0x00 Device OFF

0x01 ~ 0x63 Device ON, output Level as the specied Value.

0xFF Device ON, output Level as the last memorized Level.

Notication

The device will send notications (Notication Type =0x08, Event = 0x01) upon being

powered on.

Conguration

The congurable values are as following:

Basic Set Command value:

Parameter Number DefaultSize Range

120~99 , 255(0xFF) 255 (0xFF)

The delaying time to report to Group 1:

Parameter Number DefaultSize Range

2 1 33 - 25 (seconds)

Remember the last status:

Parameter Number DefaultSize Range

311/0 1: remember

(0: do not remember)

Output mode setting: Dimming, On/O

Parameter Number DefaultSize Range

511/0 1: Dimming

(0: On/O)

Note: When set to 1, the operation mode is not changed; only the light would be turned on

with 100% brightness immediately.

Command Classes

The module supports Command Classes including…

• COMMAND_CLASS_ZWAVEPLUS_INFO_V2

• COMMAND_CLASS_VERSION_V2

• COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

• COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1

• COMMAND_CLASS_ASSOCIATION_V2

• COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1

• COMMAND_CLASS_POWERLEVEL_V1

• COMMAND_CLASS_BASIC_V1

• COMMAND_CLASS_NOTIFICATION_V4

• COMMAND_CLASS_CONFIGURATION_V1

• COMMAND_CLASS_SWITCH_MULTILEVEL

• COMMAND_CLASS_SWITCH_ALL_V1

• COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

Additional Command Classes Supported

• Power Level: For test purpose during product installation.

• Multilevel Switch: Refer to Basic.

• Switch All: The device turns on when receiving “Switch All On”, and turns o upon

receiving “Switch All O”.

• Firmware Update: For OTA function.

Programming

Is herewith conrmed to comply with the requirements set out in the Council

Directive on the Approximation of the Laws of the Member States relating to

Radio Equipment and Telecommunications Terminal Equipment (RED) Directive

2014/54/EU, Low-voltage Directive (2014/35/EU). For the evaluation regarding the

Directives, the following standards were applied:

EN301489-1 V1.9.2

EN301489-3 V1.6.1

EN300220-1 V2.4.1

EN300220-2 V2.4.1

EN61058-1: 2002/A2: 2008

DIN VDE 0620-2-1: 2013

Company Name: Nexa Trading AB

Adress: Karl Johansgatan 152, 40242, Göteborg, Sweden

Signatur: _ __

Name: Erik Hjelmström

Title: Vice President

Date, Place: 17 May 2016, Göteborg

DECLARATION OF CONFORMITY

ad147_86802_manual_002 | 2

Produktspezifikationen

Marke:	Nexa
Kategorie:	Nicht kategorisiert
Modell:	AD-147
Tiefe:	41 mm
Produktfarbe:	Weiß
AC Eingangsspannung:	220 - 240 V
AC Eingangsfrequenz:	50 Hz
Anzahl:	1
Durchmesser:	52 mm
Max. Leistung:	250 W
Maximum Innenabstand:	30 m
Anschluss1 Formfaktor:	Gerade
Anschluss2 Formfaktor:	Gerade
HF-Übertragungsfrequenz:	868.42 MHz
Anschlussstecker-Typ:	Typ C (Euro-Stecker)
Buchsenstecker-Typ:	Typ C (Euro-Stecker)