Neff R8580X1GB Bedienungsanleitung

Neff Trockner R8580X1GB

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Neff R8580X1GB (10 Seiten) in der Kategorie Trockner. Dieser Bedienungsanleitung war für 52 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/10

1 2 3 4 5 6

Reduced temperature for delicate fabrics , for a longer drying time;'

e.g. acrylic, polyamide, elastane or acetate silk.

ˎ÷÷

Low Heat

Reduces creasing and prolongs the anti-creasing phase after the

programme has finished; can be selected in one of two levels.

ˎLess Ironing

Indicators which show the programme sequences.

Drying, Iron Dry, Cupboard Dry, End / Easy Iron.

Status indicators

Icc+cc\

Clean the fluff filter and/or air cooler under running water aPage 4/6.

Empty the condensation container.

Fill the water tank with distilled water .aPage 9

Service indicators

4 clean

. container

u water tank

ˎMenu For selecting the settings.

ˎ-/+ For changing all the settings in the display panel.

Electronic start

timer

End of the programme after ... (depending on the programme selected, e.g. 1:54h 2h;a

you can always select up to the next full hour).

1 -24 hrs

3Signal There are four buzzer volume settings: 0 (off), 1 (quiet), 2 (normal), 3 (loud), 4 (very loud). 0, 1, 2, 3, 4

#Appliance lock

(depending on the

model)

Provides protection against unintentional changes to the functions set

(press and hold the button for 5 seconds).Menu

On-Off

9Fine adjustment

of the drying result

The drying result (e.g. Cupboard Dry) can be adjusted over three levels (1 - max. 3) for the

Cottons Easy-Care, Mixed Load Rapid 40’, and programmes presetting = 0. a

After one of these programmes has been finely adjusted, the setting is retained for the others.

0, 1, 2, 3

Spin speed The spin speed that was used in the washing machine;

for more precise indication of the projected drying duration only.

600-1800 ²

... and adapt to individual requirements

Never operate the dryer if it is damaged.

Inform your after-sales service. Inspecting

the dryer

Sorting and loading laundry

Remove all objects from pockets.

Pay particular attention to cigarette lighters.

The drum must be empty before filling.

If necessary, fill the water tank for

Steam Dry / Steam Refresh programmes Page 8.a

See programme overview on page 7.

See also separate instructions for “basket for woollens”

(depending on the model)

Your new dryer

Congratulations! - You have chosen a modern, high-quality domestic

appliance from Neff.

A distinctive feature of the condensation dryer is its low energy

consumption.

Every dryer which leaves our factory is carefully checked to ensure

that it functions correctly and is in perfect condition.

Should you have any questions, our after-sales service will be pleased

to help.

Environmentally-responsible disposal

Dispose of packaging in an environmentally-responsible manner.

This appliance is designated according to European directive 

2002/96/EC which governs waste electrical and electronic

equipment (WEEE).

This directive provides the framework for the EU-wide collection and

reuse of used appliances.

For further information about our products, accessories, spare parts

and services, please visit: www.neff.de

Intended use

Contents Page

ʋPreparation . . . . . . . . . . . . . . . . . . . . . . 2

ʋSetting the programmes . . . . . . . . . . . . . 2

ʋDrying . . . . . . . . . . . . . . . . . . . . . . . . 3/4

ʋNotes on laundry . . . . . . . . . . . . . . . . . . 5

ʋCleaning and care . . . . . . . . . . . . . . . . . . 6

ʋOverview of programmes . . . . . . . . . . . . 7

ʋShort spin / Refresh . . . . . . . . . . . . . . 8/9

ʋInstallation . . . . . . . . . . . . . . . . . . . . . . 10

ʋFrost protection / Transport . . . . . . . . . .10

ʋTechnical data . . . . . . . . . . . . . . . . . . . 11

ʋOptional accessories . . . . . . . . . . . . . . .11

ʋWhat to do if... / After-sales service . . . . 12

ʋSafety instructions . . . . . . . . . . . . . . . . 13

Preparing for installation, see page 8

Selecting and adjusting the programme

Additional functions

Select the drying programme ...

Press the Start/Stop button

Only if your hands are dry.

Only hold the plug by the plug

casing.

Connecting the

mains plug

Display panel

All buttons are sensitive,

a light touch is enough!

Drying / Short spin /

Refresh

Drying Emptying condensation

Empty the container each drying cycle, not during drying!after

1. Remove the container, holding it level.

2. Pour out condensation.

3. Push the .container back in until it clicks into place.

Cleaning the fluff filter

1. Open the door, remove the filter and fold open.

2. Remove the fluff (by wiping the filter with your hand).

3. Close the filter, insert it again and close the door.

4. Remove fluff from the door and the area around it.

Very dirty or blocked filters should be rinsed under warm

water, and then dried thoroughly.

Clean the filter in the water tank if it is dirty

1. Remove the condensation tank.

2. Remove the filter.

3. Clean the filter under running water.

4. Re-insert the filter and push in the condensation tank until it clicks into

place.

Switching off the dryer

Turn the programme selector to .Off

Do not leave damp laundry in the dryer.

Removing the laundry

The automatic Easy Iron function moves the drum at certain intervals. The load remains loose and soft for

an hour (or two hours if you manually select the function, depending on the model.)Less Ironing

Information on laundry ...

Labelling of fabrics

Follow the manufacturer's care information.

(Drying at normal temperature.

'c cDry at a low temperature selecta÷ ÷Low Heat as well.

)cDo not machine dry.

Do not tumble-dry the following fabrics:

– Airtight fabrics (e.g. rubber-coated fabrics).

– Delicate materials (silk, curtains made from synthetic material) they may crease.a

– Oil-stained laundry.

Drying tips

– To ensure a consistent result, sort the laundry by fabric type and drying programme.

– Close zips, hooks and eyes, and do up any buttons.

Tie belts, apron strings etc. together.

– Do not overdry easy-care laundry risk of creasinga

Allow laundry to finish drying in the air.

– Do not iron laundry immediately after drying, fold items up and leave for a while

a the remaining moisture will then be distributed evenly.

– The drying result depends on the type of water used during washing. a

Fine adjustment of the drying result Page 1/2a.

– Knitted fabrics (e.g. T-shirts, jerseys) often shrink slightly the first time they are tumble-dried.

a Do not select the programme.Extra Dry

– Starched laundry is not always suitable for dryers starch leaves behind a coating that a

adversely affects the drying operation.

– When washing laundry that is to be tumble-dried afterwards, dose the fabric softener

according to the manufacturer's instructions.

– With a small load, use the Timed Program.

Tips for Steam Dry / Steam Refresh

– Use your dryer for unwrinkling and refreshing fabrics.

– Short spin cycle for reducing creasing.

– Refresh cycle for reducinging odours from fabrics.

Do not use Steam Dry / Steam Refresh for the following fabrics:

– Wool, leather, fabrics with metal, wooden or plastic parts.

– Wax and oil jackets.

– Sort the laundry by colour and put on separate short Steam Dry / Steam Refresh cycles

to prevent the colours from bleeding.

– These programmes do not remove stains stains must be treated and removed a

beforehand.

– For best results, so that the laundry will have as few creases as possible, remove each item

immediately after the programme has finished and hang on a hanger to finish drying.

Pull clothes into shape if required.

Environmental protection / Energy-saving tips

– Before drying, spin the laundry thoroughly in the washing machine the higher the spin a

speed, the shorter the drying time will be (consumes less energy), also spin easy-care

laundry.

– Use the maximum recommended capacity, but do not exceed it

aPage 7, “Programme overview”.

– Make sure the room is well ventilated during drying.

– Clean the fluff filter after each drying cycle .aPage 4

– Keep the air cooler clean .aPage 6 “Cleaning and care”

– Keep the supply of cool air unobstructed Do not cover or block the cooling grill.a

Condensation container

Control panel

Air inlet

Fluff filter

Drum

Cleaning and care

Dryer housing, control panel, air cooler, moisture sensors

– Wipe with a soft, damp cloth.

– Do not use harsh cleaning agents and solvents.

– Remove detergent and cleaning agent residue immediately.

– During drying, water may collect between the door and seal. This does not affect your

dryer's functions in any way.

Clean the protective filter 5 - 6 times a year

or if 4 flashes after the fluff filter has been cleaned.

Air cooler / Protective filter

When cleaning, only remove the protective filter.

Clean the air cooler behind the protective filter once a year.

– Allow the dryer to cool.

– Residual water may leak out, so place an absorbent towel

underneath the maintenance door.

1. Unlock the maintenance door.

2. Open the maintenance door fully.

3. Turn both locking levers towards each another.

4. Pull out the protective filter/air cooler.

Do not damage the protective filter or air cooler.

Clean with warm water only. Do not use any hard or sharp-edged

objects.

5. Clean the air cooler thoroughly.

Allow to drip dry.

6. Clean the seals.

7. Re-insert the protective filter/air cooler,

with the handle facing down.

8. Turn back both locking levers.

9. Close the maintenance door until the lock clicks into place.

Moisture sensors

The dryer is fitted with stainless steel moisture sensors. The sensors

measure the level of moisture in the laundry. After a long period of

operation, a fine layer of limescale may form on the sensors.

1. Open the door and clean the moisture sensors with a damp sponge

which has a rough surface.

Do not use steel wool or abrasive materials.

Cover for steam nozzle in the drum

After lengthy operation, limescale and fluff may accumulate on

the cover of the steam nozzle. Clean regularly:

1. Open the door and remove the cover with a screw driver.

Clean the cover under running water.

2. Push and click the protective cap back in place.

Cover for

steam nozzle

Air cooler

Programme end once \ lights up in the display.

Interrupt programme removing or adding laundry.

The drying cycle can be interrupted for a brief period so that laundry may be added or removed.

The selected programme must then be continued until it is finished.

Hot steam may escape during the Steam Drying / Steam Refresh programmes.

1. Open the door. The drying cycle is paused.

2. Remove or add laundry and close the door.

3. If required, select a new programme and additional functions.

4. Press the /Stop button. The remaining time is updated after a few minutes.Start

Water tank

filling hole

with filter

Only when switched off!

Read these instructions and the separate

Energy-saving mode instructions before

operating the dryer.

Observe the safety instructions on page 13.

Caution - risk of scalding.

ʋFor domestic use only.

ʋOnly to be used for drying, refreshing or unwrinkling

fabrics that have been washed with water.

Do not leave children

unsupervised near the dryer.

Keep pets away from the dryer.

The dryer can be operated by children 8 years old

and older, by persons with reduced physical,

sensory or mental abilities and by persons with

insufficient experience or knowledge if they are

supervised or have been instructed in its use

by a responsible adult.

Programme selector

Programme overview see also pages 5 and 8

Sort the laundry according to type of textile and fabric. Fabrics must be suitable for tumble drying.

After drying...

c

iron laundry



lightly iron laundry

do not iron laundry

mangle laundry

PROGRAMMES TEXTILE TYPE AND INFORMATION

**Cottons max. 7 kg Hard-wearing fabrics, boil-resistant fabrics made of cotton or linen.

**Easy-Care max. 3.5 kg Non-iron laundry made of synthetic fibres and blended fabric, easy-care cotton.

**Mixed Load max. 3 kg Mixed items of laundry madeof cotton and synthetics (Mix).

Iron Dry c @c ÷ Fabrics suitable for ironing (iron fabrics in order to avoid creasing).

Cupboard Dry @Single-layer fabrics.

* Extra Dry @Fabrics made of thick, multilayered items of clothing.

Steam Drying For smoothing hard-wearing and easy-care fabrics. Steam smooths the fabrics.

Minimum Iron Daily Load max. 2.5 kg Further information Page 8.a

Minimum Iron Shirt max. 1.5 kg

Steam Refresh For freshening hard-wearing and easy-care fabrics. Steam freshens up the fabrics.

Business max. 1.5 kg Further information Page 8.a

Freshen up max. 1 kg

Sports max. 1.5 kg Fabrics with membrane coating, water-repellent fabrics, functional clothing, fleece fabrics

(dry jackets/trousers with removable internal lining separately).

Woollens Finish max. 3 kg Woollen fabrics suitable for washing machines. Fabrics become fluffier but not dry.

Remove fabrics once the programme has ended and allow to dry.

Rapid 40’ max. 2 kg

Laundry made of synthetic fibres, cotton or blended fabrics (for example) that needs to be dried quickly. The values may

differ from the those specified depending on the type of fabric, mixture of laundry to be dried, residual moisture in the

fabric and loading capacity.

Timed Programme/warm max. 3 kg Pre-dried, multi-layered, sensitive fabrics made of acrylic fibres, or separate small items of laundry.

Also for subsequent drying.

*for and programmes onlyCottons Easy-Care

**Dryness levels can be selected individually Extra Dry, Cupboard Dry and Iron Dry .a (depending on the model)

Degree of dryness can be finely adjusted; multi-layered textiles require a longer drying time than single-layered items of clothing.

Recommendation: Dry separately.

9304 / 9000882842

*882842* R8580X1GB

Steam Drying - Steam Refresh

Steam programmes for unwrinkling or refreshing

– Your dryer has unwrinkling and refreshing programmes that can be used for reducing

odours and minimising creasing in dry fabrics. Steam smooths and freshens up items

– of clothing.

– Sorting the laundry according to size, weight, fabric and colour is necessary.

– Only use Short spin/Refresh for fabrics with the same properties.

– During steam generation (required), additional noises may occur.

– The result of refreshing and unwrinkling may vary depending on the type of fabric,

size of the load and programme selected.

– After unwrinkling or refreshing, all fabrics must be removed immediately and hung

crease-free on a hanger or a washing line for 15 minutes.

Programmes

Please observe the treatment symbols and manufacturer's instructions on the fabrics.

Do not use Short spin/Refresh for fabrics made of wool, leather, containing metal or

wooden parts as well as wax and oil jackets!

Do not use any dryer cleaning sets!

ʑSteam Drying

Minimum Iron Shirt

Suitable for easy-care fabrics, e.g. formal shirts. Fabrics are smoothed. You can expect

optimum results if “non-iron” appears on the care label. After the programme has finished,

the items must be removed immediately and hung crease-free on a hanger or washing line

for 15 minutes. The programme is for up to 5 formal shirts.

Minimum Iron Daily Load

Suitable for hard-wearing cotton fabrics, e.g. bed linen, tablecloths or formal shirts. Fabrics

are smoothed. You can expect optimum results if “non-iron” appears on the care label. After

the programme has finished, the items must be removed immediately and hung crease-free

on a hanger or washing line for 15 minutes. The programme is for up to 5 formal shirts or

1 to 2 larger items.

ʑSteam Refresh

Business

Suitable for refreshing suits, jackets and trousers, or dry-clean items that cannot be washed

in the washing machine see the care label. The programme only refreshes fabrics and a

does not clean them. After the end of the programme, the items must be removed

immediately. Programme for 1 suit or 1 to 2 smaller items.

Freshen up

Suitable for refreshing casual wear made of cotton or artificial fibres. Fabrics must be

suitable for dryers a see the care label. The programme refreshes fabrics only, and does

not clean them. After the programme has finished, the fabrics must be removed

immediately. Programme for 1 pullover, 2 pairs of trousers or formal shirts.

Steam Drying - Steam Refresh

Your water tank empties automatically after the programme has finished.

Cleaning is therefore not required

Filling the water tank:

Fill the dryer's water tank with distilled water before every Steam Drying - Steam Refresh

cycle.

1. Steam DryingMove the programme selector to

or .Steam Refresh

The appears in the display.u symbol

2. Remove the condensation tank completely.

Before every Steam Drying - Steam Refresh cycle, fill the water tank with

distilled water only. Do not use tap water, condensation or additives.

3. Fill the water tank. Use the jug supplied.

If the water tank filter is dirty aclean the filter in the water tank.

See page 4.

4. Pour the distilled water into the filling hole on the water tank,

until the symbol goes out on the display panel.u

If drying the recommended load, approximately 250 to 300 ml of distilled

water is used in the Steam Drying - Steam Refresh programmes.

5. Insert the condensation container all the way.

6. Steam Drying Steam RefreshStart the or programme.

Installation

– Scope of delivery: dryer, installation and instruction manual, jug, basket for woollens

(depending on the model).

– Check dryer for transport damage.

– The dryer is heavy. Do not attempt to lift it on your own.

– Be careful to avoid sharp edges.

– Do not install in a room where there is a risk of freezing. Freezing water may cause damage.

– If in doubt, have the appliance connected by a specialist.

– Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.

Setting up the dryer

– The appliance plug must always be accessible.

– Ensure that the appliance is installed on a clean, level

and firm surface.

– Keep the cooling grille on the front of the dryer

clear.

– Keep the area around the dryer clean.

– Level the dryer using the threaded feet.

Use a spirit level.

– Do not remove the threaded feet under any

circumstances.

Mains connection see safety information page 13.a

– Connect to an AC earthed socket. If in doubt, have the socket checked by a specialist.

– The mains voltage and the voltage shown on the rating plate (aPage 11) must be the same.

– The connected load and necessary fuse protection are specified on the rating plate.

Frost protection / Transport

Preparation

1. Empty the condensation container .apage 4

2. Select any programme using the programme selector.

3. Press the /Stop button Start a condensation is pumped into the container.

4. Wait 5 min., and then empty the condensation container again.

5. Turn the programme selector to .Off

The water tank must not contain any distilled water. If necessary, run the Steam/Refresh programme.

Remove all accessories

from the drum.

The drum must be empty.

Make sure that the air inlet

remains unobstructed

Clean and level

Do not install the dryer behind a door or sliding

door, which could prevent or restrict opening of the

dryer door. This will prevent children from locking

themselves in and putting their lives in danger.

Do not operate the dryer if there

is a danger of frost.

Technical data

ʠDimensions (DxWxH) 60 x 60 x 85 cm (adjustable height)

Weight approximately 43.5 kg

Max. capacity 7 kg

Condensation container 4.0 l

Water tank approx. 0.4 l

Connection voltage 220-240 V

Connected load max. 2600 W

Fuse protection 13 A

Ambient temperature 5 - 35 °C

Product number

Production number Inside of door

The rating plate can be found on the back of the dryer.

ʠDrum interior light (bulb E14, 25 W)(depending on model)

The drum lights up after the door is opened or closed, and after the programme starts,

and switches off automatically. Changing the bulb page 12.a

Consumption rates (The value on the label is achieved at the maximum heat setting.)

Fabrics/programmes Residual moisture in the

fabrics after spinning

Drying time** Energy

consumption**

Cottons 7 kg 13 A 13 A

Cupboard Dry* 1400 U/min (50%) 106 min 3.60 kWh

1000 U/min (60%) 124 min 4.20 kWh

800 U/min (70%) 143 min 4.80 kWh

Iron Dry* 1400 U/min (50%) 82 min 2.59 kWh

1000 U/min (60%) 98 min 3.28 kWh

800 U/min (70%) 112 min 3.96 kWh

Easy-Care 3.5 kg

Cupboard Dry* 800 U/min (40%) 42 min 1.35 kWh

600 U/min (50%) 51 min 1.65 kWh

* Programme setting for testing in accordance with applicable standard EN61121.

** The values may differ from those specified, depending on the type of fabric, composition of

laundry to be dried, residual moisture in the fabric and the amount of laundry being loaded.

Fabrics/programmes Drying time Annual energy consumption

Cottons 7 kg / 3.5 kg*

Cupboard Dry*** 97 min / per cycle 504 kWh / per year

***Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.

Optional accessories (from after-sales service using order number)

Washer-dryer stack connection set

The dryer can be placed on top of a suitable washing machine with the same width and depth

to save space. The dryer must be fastened to the washing machine using this connection set.

Connection fittings for condensation outlet

The condensation is conveyed directly via a hose.

Installation underneath the worktop

Instead of the appliance covering plate, you must have a metal cover fitted by

a specialist.

11390

20160

20290

What to do if...

If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales

service. We will always find an appropriate solution and will avoid unnecessary visits by

engineers. Trust the expertise of the manufacturer and rest assured that the repair will be

carried out by trained service technicians using original spare parts. The contact details of your

local after-sales service can be found in the enclosed after-sales service directory, or by

calling one of these numbers:

– 0844 892 8989 (Calls from a BT landline will be charged at up to 3 pence per minute. GB

A call set-up fee of up to 6 pence may apply.)

– 01450 2655 IE

When contacting the after-sales service, please quote the appliance's product number (E no.)

and production number (FD) (see the inside of the door).

Set the programme selector to and remove the appliance plug from the socket.Off

ʠThe Start/Stop indicator light does

not come on.

Mains plug plugged in?

Programme selected?

Check the socket fuse.

ʠThe display panel light and

indicator lights (depending on

model) go out and the

Start/Stop indicator light flashes.

Energy-saving mode is activated

see the separate

Energy-saving mode instructions.

ʠThe ā symbol and Start/Stop

indicator light are flashing.

Empty the condensation container a Page 4.

Check the condensation outlet hose, if applicable (kink).

ʠThe 4 symbol and /Stop Start

indicator light are flashing.

Clean the air cooler aPage 6 “Cleaning and care”. Clean the

fluff filter .aPage 4

ʠThe u symbol flashes. Is the water tank empty?

Filling with distilled water .a Page 9

The filter in the water tank may have become dirty.

If so, clean the filter in the water tank .aPage 4

ʠThe Steam Drying - Steam Refresh

does not start.

ʠDryer does not start. Has the Start/Stop button been pressed? Is the door closed?

Programme set?

Ambient temperature greater than 5 °C?

ʠWater is leaking out. Make sure the dryer is level.

Clean the air cooler seal.

ʠThe door opens by itself. Push the door closed until you hear it click into place.

ʠItems crease even though the

Steam Drying - Steam Refresh

programme has been selected.

Laundry load exceeded?

Remove articles of clothing immediately after the end of the

programme, hang up and pull into shape.

Unsuitable programme selected a Page 7.

ʠDrying result is not satisfactory

(laundry feels too damp).

Warm laundry feels damper than it actually is.

The selected programme does not suit the load. Use another

drying programme or, in addition, select the time programme

aPage 7.

Use fine adjustment for the drying result aPage 1/2.

Fine layer of limescale on the humidity sensors

a Clean the humidity sensors aPage 6.

Programme termination, e.g. tank full, mains power supply

failure, door open or maximum drying time reached.

ʠDrying time too long. Rinse the fluff filters under running water a Page 4.

Insufficient supply of air a ensure that air can circulate.

Air inlet possibly blocked Clear inlet a a Page 10.

Ambient temperature higher than 35 °C a ventilate the room.

ʠThe humidity in the room increases

significantly.

Make sure the room is sufficiently ventilated.

ʠOne or more programme status

indicator lamps are flashing.

Clean the filter and air cooler under running water aPage 4/6.

Check the installation conditions aPage 10.

Switch off, allow to cool, switch on again and restart the

programme.

ʠThe interior light (depending on the

model) does not work.

Unplug the appliance plug, fold back the cover cap on

the inside above the door (using a Torx 20 screwdriver)

and replace the bulb. Close the cover cap.

Safety instructions

Emergency

– Pull the appliance plug out of the socket immediately or disconnect the fuse.

ONLY use the

dryer...

– in rooms inside the house.

– for drying or unwrinkling/refreshing fabrics.

The dryer must

NEVER...

– be used for purposes other than those described above.

– be modified in terms of its technology or properties.

Hazards

– The dryer must not be used by children or persons who have not been

instructed in its use.

– Do not leave children unsupervised near the dryer.

– Keep pets away from the dryer.

– Remove all objects from pockets,

and lighters in particular a risk of explosion.

– Do not lean or sit on the door a risk of tipping.

– Open the door carefully. Hot steam may escape. The clothes and drum may

be hot a risk of burns.

Installation

– Secure loose leads or hoses, otherwise there is a risk of tripping.

– Below 0 °C there is a possibility of frost damage.

Mains

connection

– Connect the dryer according to specifications to an AC earthed socket,

otherwise it cannot be guaranteed that the appliance is completely safe.

– The cable cross-section must be sufficient.

– Only use earth-leakage circuit breakers with the following symbol:

– The appliance plug and socket must be compatible.

– Do not use multiple plugs/connectors and/or extension cables.

– Do not touch or hold the appliance plug with wet hands

a risk of electric shock.

– Never pull the appliance plug out of the socket by its cable.

– Do not damage the mains lead a risk of electric shock.

Operation

– Only laundry must be loaded into the drum.

Before switching on the dryer - check the contents.

– Do not use the dryer if the laundry has been in contact with solvents, oil, wax,

grease or paint (e.g. hair setting spray, nail polish remover, stain remover,

cleaning solvent, etc.) a fire/explosion hazard.

– Hazard caused by dust (e.g. coal dust, flour): do not use the dryer

a risk of explosion.

– Do not put laundry containing foamed material/rubber in the dryer elastic a

material may be destroyed and the dryer may be damaged due to possible

deformation of the foamed material.

– Switch off the dryer once the programme has ended.

– For unwrinkling/refreshing fabrics, use distilled water only. Do not use

condensation, tap water or additives.

– Distilled/condensation water is not for drinking.

Defect

– Do not use the dryer if it is defective or if you suspect that it is.

Repairs must only be carried out by the after-sales service.

– Do not use a dryer with a faulty mains lead. To prevent risks, a faulty mains

lead must only be replaced by the after-sales service.

– Before changing the bulb of the interior light make absolutely sure you have

pulled the appliance plug from the socket a risk of electric shock.

Spare parts

– Only use genuine spare parts and accessories for safety reasons.

Disposal

– Dryer: unplug the appliance plug, then cut the mains lead from the appliance.

Dispose of the dryer at an approved public disposal facility.

– Packaging: keep all packaging out of reach of babies and children.

a danger of suffocation.

– All materials are environmentally safe and recyclable. Dispose of in an

environmentally-responsible manner.

INSTRUCTIONS FOR INSTALLATION AND USE

TUMBLE DRYER

1 2

Reduced temperature for delicate fabrics , for a longer drying time;'

e.g. acrylic, polyamide, elastane or acetate silk.

ˎ÷÷

Low Heat

Reduces creasing and prolongs the anti-creasing phase after the

programme has finished; can be selected in one of two levels.

ˎLess Ironing

Indicators which show the programme sequences.

Drying, Iron Dry, Cupboard Dry, End / Easy Iron.

Status indicators

Icc+cc\

Clean the fluff filter and/or air cooler under running water aPage 4/6.

Empty the condensation container.

Fill the water tank with distilled water .aPage 9

Service indicators

4 clean

. container

u water tank

ˎMenu For selecting the settings.

ˎ-/+ For changing all the settings in the display panel.

Electronic start

timer

End of the programme after ... (depending on the programme selected, e.g. 1:54h a

you can always select up to the next full hour).

3Signal There are four buzzer volume settings: 0 (off), 1 (quiet), 2 (normal), 3 (loud), 4 (very loud).

#Appliance lock

(depending on the

model)

Provides protection against unintentional changes to the functions set

(press and hold the button for 5 seconds).Menu

9Fine adjustment

of the drying result

The drying result (e.g. Cupboard Dry) can be adjusted over three levels (1 - max. 3) for the

Cottons Easy-Care, Mixed Load Rapid 40’, and programmes presetting = 0. a

After one of these programmes has been finely adjusted, the setting is retained for the others.

Spin speed The spin speed that was used in the washing machine;

for more precise indication of the projected drying duration only.

... and adapt to individual requirements

Never operate the dryer if it is damaged.

Inform your after-sales service.

Sorting and loading laundry

Remove all objects from pockets.

Pay particular attention to cigarette lighters.

The drum must be empty before filling.

If necessary, fill the water tank for

Steam Dry / Steam Refresh programmes Page 8.a

See programme overview on page 7.

See also separate instructions for “basket for wool

(depending on the model)

Your new dryer

Congratulations! - You have chosen a modern, high-quality domestic

appliance from Neff.

A distinctive feature of the condensation dryer is its low energy

consumption.

Every dryer which leaves our factory is carefully checked to ensure

that it functions correctly and is in perfect condition.

Should you have any questions, our after-sales service will be pleased

to help.

Environmentally-responsible disposal

Dispose of packaging in an environmentally-responsible manner.

This appliance is designated according to European directive 

2002/96/EC which governs waste electrical and electronic

equipment (WEEE).

This directive provides the framework for the EU-wide collection and

reuse of used appliances.

For further information about our products, accessories, spare parts

and services, please visit: www.neff.de

Intended use

Contents Page

ʋPreparation . . . . . . . . . . . . . . . . . . . . . . 2

ʋSetting the programmes . . . . . . . . . . . . . 2

ʋDrying . . . . . . . . . . . . . . . . . . . . . . . . 3/4

ʋNotes on laundry . . . . . . . . . . . . . . . . . . 5

ʋCleaning and care . . . . . . . . . . . . . . . . . . 6

ʋOverview of programmes . . . . . . . . . . . . 7

ʋShort spin / Refresh . . . . . . . . . . . . . . 8/9

ʋInstallation . . . . . . . . . . . . . . . . . . . . . . 10

ʋFrost protection / Transport . . . . . . . . . .10

ʋTechnical data . . . . . . . . . . . . . . . . . . . 11

ʋOptional accessories . . . . . . . . . . . . . . . 11

ʋWhat to do if... / After-sales service . . . .12

ʋSafety instructions . . . . . . . . . . . . . . . . 13

Preparing for installation, see page 8

Selecting and adjusting the programme

Additional functions

Select the drying programme ...

Press the Start/Stop button

Only if your hands are dry.

Only hold the plug by the plug

casing.

Connecting the

mains plug

Display panel

All buttons are sensitive,

a light touch is enough!

(

'c ca÷ ÷

Read these instructions and the separate

Energy-saving mode instructions before

operating the dryer.

Observe the safety instructions on page 13.

Caution - risk of scalding.

ʋFor domestic use only.

ʋOnly to be used for drying, refreshing or unwrinkling

fabrics that have been washed with water.

Do not leave children

unsupervised near the dryer.

Keep pets away from the dryer.

The dryer can be operated by children 8 years old

and older, by persons with reduced physical,

sensory or mental abilities and by persons with

insufficient experience or knowledge if they are

supervised or have been instructed in its use

by a responsible adult.

Programme selector

Produktspezifikationen

Marke:	Neff
Kategorie:	Trockner
Modell:	R8580X1GB
Breite:	598 mm
Tiefe:	626 mm
Produktfarbe:	Weiß
Steuerung:	Rotary, Touch
Höhe:	842 mm
Eingebautes Display:	Ja
Geräteplatzierung:	Freistehend
Energieeffizienzklasse:	B
Stromverbrauch (Standby):	1 W
Trockenprogramme:	Wool, Mix, Sport, Quick, Steam
Startzeitvorwahl:	Ja
Anti-Faltenfunktion:	Ja
Ladetyp:	Frontlader
Jährlicher Energieverbrauch:	504 kWh
Wärmequelle:	Elektro
Energieverbrauch:	4.2 kWh
Zykluszeit:	124 min
Nennkapazität:	7 kg
Trocknungsklasse:	B
Geräuschpegel:	64 dB
Anti-Falten Programm:	120 min
Trommelmaterial:	Edelstahl
Türanschlag:	Rechts
Trocknungssystem:	Kondensation
Einschalteverzögerung (max.):	24 h
Kindersicherung:	Ja
Stromverbrauch (aus):	0.1 W
Alarm:	Ja
Trommelinnenbeleuchtung:	Ja
LED Programm-Kontrollleuchte:	Ja