NAD MDC DAC 2.0 Bedienungsanleitung

NAD Nicht kategorisiert MDC DAC 2.0

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für NAD MDC DAC 2.0 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
®
ASYNCHRONOUS USB DAC MODULE
Mounting Instructions
MOUNTING INSTRUCTIONS FOR THE C375BEE
The DAC Module is compatible with C375BEE. Using the supplied exible at
cable (FFC), DC power connector and screws, the DAC Module can be installed
in a C375BEE by undertaking the following procedure.
Note that if the C375BEE has a PP375 Phono Preamplier Module already
installed, the DAC module and the PP375 can be linked together using the other
supplied FFC.
STEP 1
Pre-install the requisite cables to their respective connector points on the DAC
Module as shown. Connect the FFC to the DAC Modules PP375 IN only if the
C375BEE has a PP375 already installed.
STEP 2
Make the following connections:
1 DC POWER connector from DAC Module to corresponding P216B in
C375BEEs main board.
2 FFC from DAC Module’s ANALOG OUT to P213B on C375BEEs main board.
3 If the optional PP375 module is installed: FFC from DAC Modules PP375 IN
to the corresponding FPC (exible printed circuit) connector of the PP375
module.
Ensure good harnessing by exing and safely contorting the FFC and
DCPOWER connectors.
STEP 3
Remove the dummy cover at the back of the C375BEE and install in its place the
DAC Module. Use the supplied screws to x into place the DAC Module.
3
2
1
IMPORTANT!
The DAC module is only compatible with C 375BEE units that have the
0.5Wstandby logo on their rear panels.
©2015 NAD ELECTRONICS INTERNATIONAL, A DIVISION OF LENBROOK INDUSTRIES LIMITED
All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited.
No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
MDCDAC_QS_V06  04/15
1
2
MOUNTING INSTRUCTION FOR THE C356BEE
The DAC Module is compatible with C356BEE. Using the supplied exible at
cable (FFC), DC power connector and screws, the DAC Module can be installed
in a C356BEE by undertaking the following procedure.
STEP 1
Pre-install the requisite cables to their respective connector points.
Connect the following
1 DC POWER connector from DAC Module to corresponding CB48 on
C356BEE’s main board.
2 FFC from DAC Module’s ANALOG OUT to CB36 on C356BEEs main board.
Ensure good harnessing by exing and safely contorting the FFC and DC POWER
connectors.
STEP 2
Remove the dummy cover at the back of the C356BEE and install in its place the
DAC Module. Use the supplied screws to x into place the DAC Module.


Produktspezifikationen

Marke: NAD
Kategorie: Nicht kategorisiert
Modell: MDC DAC 2.0

Brauchst du Hilfe?

Wenn Sie Hilfe mit NAD MDC DAC 2.0 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert NAD

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-