Moxa MGate 5101-PBM-MN-T Bedienungsanleitung

Moxa Nicht kategorisiert MGate 5101-PBM-MN-T

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Moxa MGate 5101-PBM-MN-T (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
P/N: 1802051010014
*1802051010014*
MGate 5101- - PBM MN Series
Quick Installation Guide
Vers 20ion January 3.2, 21
Technical Support Contact Information
www.moxa.com/support

2 . A 20 1 Moxa Inc ll rights reserved.
- - 2
Overview
The MGate 5101-PBM-MN is an industrial Ethernet gateway for
PROFIBUS- - - to Modbus TCP network communication.
Package Checklist
Before installing the MGate 5101-PBM-MN, verify that the package
contains the following items:
• -PBM- 1 MGate 5101 MN gateway
• i g Quick nstallation uide (printed)
• Warranty Card
Please notify your sales representative if any of the above items are
missing or damaged.
Optional Accessories (can be purchased separately):
• - - - - - - CBL F9M9 150: DB9 female to DB9 male serial cable, 150 cm
• - - - - - - CBL F9M9 20: DB9 female to DB9 male serial cable, 20 cm
• - - - - - Mini DB9F to TB: DB9 female to terminal- block connector
• - - - WK 36 01: Wall mounting kit
Hardware Introduction
LED Indicators
LED
Color
PWR1
Green
Off
PWR2
Green
Off
Ready
Green
Steady on: Power is on and the MGate is
functioning normally
Blinking: The MGate has been located by the
Red
up
Blinking: Indicates an IP conflict, or the DHCP or
Off
COMM
Off
Green
Green,
flashing
Data exchange with at least one slave (not all
Red
CFG
Off
Green
PBM
Off
Red
Green,
flashing
PROFIBUS master is in CLEAR mode
Green
TOK
Green
Off
- - 3
LED
Color
Ethernet
Amber
Green
Off
Reset Button
The reset button is used to load factory defaults. Use a pointed object
such as a straightened paper clip to hold the reset button down for five
seconds. Release the reset button when the Ready LED stops blinking.
Hardware Installation Procedure
STEP 1 :
C -onnect the power adapter. Connect the 12 48 VDC power line
or DIN
-rail power supply with the MGate -PBM-5101 MN
device’s terminal block.
Make sure the adapter is connected to
an earthed socket.
STEP 2:
Use a PROFIBUS cable to connect the unit to a PROFIBUS slave
device.
STEP 3 :
Connect the unit to the Modbus TCP device.
STEP 4
:
The
MGate -PBM- 5101 MN series is designed to be
attached to
a DIN
- rail or mounted on a wall. For DIN rail
mounting, push
down the spring and properly attach it to the
-DIN
rail until it
“snaps” into place. For wall
mounting, install the wall-mount
kit (optional) firs
t and then screw the device onto the wall.
Wall or Cabinet Mounting
Two metal plates are provided for mounting the
unit on a wall or inside a cabinet. Attach the plates
to the unit’s rear panel with screws. With the plates
attached, use screws to mount the unit on a wall.
The heads of the screws should be 5 to 7 mm in
diameter, the shafts should be 3 to 4 mm in
diameter, and the length of the screws should be
more than 10.5 mm.
For each screw, the head should be 6 mm or less in diameter, and the
shaft should be 3.5 mm or less in diameter.


Produktspezifikationen

Marke: Moxa
Kategorie: Nicht kategorisiert
Modell: MGate 5101-PBM-MN-T
Gewicht: 500 g
Betriebstemperatur: -40 - 75 °C
Relative Luftfeuchtigkeit in Betrieb: 5 - 95 %
Anzahl Ethernet-LAN-AnschlĂĽsse (RJ-45): 1
Temperaturbereich bei Lagerung: -40 - 85 °C
Abmessungen (BxTxH): 36 x 105 x 140 mm
Eingangsspannung: 12 - 48 V
Sicherheit: UL 60950-1, EN 60950-1
Höhe bei Betrieb: 0 - 2000 m

Brauchst du Hilfe?

Wenn Sie Hilfe mit Moxa MGate 5101-PBM-MN-T benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Moxa

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-