Moxa INJ-24A Bedienungsanleitung

Moxa WLAN-Repeater INJ-24A

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Moxa INJ-24A (10 Seiten) in der Kategorie WLAN-Repeater. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/10

 12 . A20 Moxa Inc ll rights reserved.

P/N: 1802000240020

Moxa High-Power PoE+ Injector

INJ- A 24 Series

Hardware Installation Guide

First 2 Edition, October 201

- - 2

Overview

The Moxa INJ- -24A Series high power PoE+injector is a 1-port PoE+

injector that delivers both data and electrical power to Ethernet-enabled

devices using a single Ethernet cable. The INJ-24A can supply up to 36

watts of power in 2- pair mode or 60 watts in 4-pair mode through the

Ethernet port, and can power IEEE 802.3af/at compliant powered devices

(PD), such as wireless access points or IP cameras, eliminating the need

for additional wiring. The INJ-24A supports Gigabit communication, which

is vital for high-speed and low-latency applications. The INJ-24A also

offers a wide operating temperature range of -40 to 75°C, and is designed

to withstand a high degree of vibration and shock. An innovative

hardware design enhances the INJ-24A with flexible options of Mode A

and Mode B PoE powering modes. This makes the INJ-24A perfect for

outdoor field installation of M12-connector wireless APs and IP cameras

which only have 4 pins in the cable. In addition, the - INJ 24A can resist

3KV surges from the PoE port, protecting s system operation in critical

industrial environments, and complies with CE/FCC and UL standards for

safet y.

Wiring Requirements

WARNING

Do not disconnect modules or wires unless the power supply has

been switched off o

r the area is known to be non-

hazardous. The

devices may only be connected to the supply voltage shown on

the type plate. The devices are designed for operation with a

Safety Extra

Low Voltage. Thus, they may only be connected to

the supply voltage connections and to the signal contact with the

Safety Extra

-Low Voltages (SELV) in compliance with IEC

60950 1.-1/EN 60950-

WARNING

The power for this product is intended to be supplied by a Listed

Power Unit, with output marked LPS, and rated to deliver 24 DC

at a maximum of 3.72 A.

WARNING

This unit is a built

-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must

comply with fire enclosure regulation IEC 60950

- -1/EN60950 1

(or similar regulation).

- - 3

WARNING

Safety First!

Be sure to disconnect the power cord before

installing and/or

wiring your Moxa PoE injector. Calculate the maximum possible

current in each power wire and common wire. Observe all

electrical codes dictating the maximum current allowable for each

wire size. If the current goes above the maximum ratin

gs, the

wiring could overheat, causing serious damage to your

equipment.

You should also pay attention to the following items:

• Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

• NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

• You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

• Keep input wiring and output wiring separated.

• It is strongly advised that you label wiring to all devices in the system

when necessary.

Package Checklist

The Moxa - A INJ 24 Series is shipped with the following items. If any of

these items is missing or damaged, contact a Moxa customer service

representative for assistance.

• Moxa INJ- - 24A High Power PoE+ Injector

• Hardware Installation Guide

• Moxa Product Warranty Statement

Features

High Performance Technology

• 10/100/1000BaseT(X)

• Provides up to 36 watts (2-pair mode) or 60 watts (4- pair mode) per

PoE port

• Built- in 24/48 VDC booster for PoE and PoE+

Innovative Easy Installation

• Selectable PoE Mode A and Mode B connection options

• SmartPoE LED indication

Produktspezifikationen

Marke:	Moxa
Kategorie:	WLAN-Repeater
Modell:	INJ-24A
WLAN:	Nein
Breite:	30.3 mm
Tiefe:	78.8 mm
Gewicht:	245 g
Produktfarbe:	Metallisch
Höhe:	115 mm
AC Eingangsspannung:	12-48 V
Betriebstemperatur:	-40 - 75 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Netzstandard:	IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Zertifizierung:	EN 61000-4-2 (ESD) Level 3, EN 61000-4-3 (RS) Level 3, EN 61000-4-4 (EFT) Level 3, EN 61000-4-5 (Surge) Level 3, EN 61000-4-6 (CS) Level 3, EN 61000-4-8, FCC Part 15 Subpart B Class A, EN 55022 Class A
Power over Ethernet (PoE):	Ja
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	2
Typ:	Netzwerk-Repeater
LED-Anzeigen:	Ja
Temperaturbereich bei Lagerung:	-40 - 85 °C
Mittlere Betriebsdauer zwischen Ausfällen (MTBF):	2407739 h
Eingangsstrom:	3.72 A
Verkabelungstechnologie:	10/100/1000Base-T(X)
Maximal mögliche Übertragungsstrecke:	- m