Moxa A53-DB9F Bedienungsanleitung

Moxa Nicht kategorisiert A53-DB9F

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Moxa A53-DB9F (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Serial Communication Interface Conversion Solution
Transio A52/53 User’s Manual P/N: 1802000520516 Seventh Edition.
www.moxa.com ©2008 Moxa Inc.
Moxa Inc. All rights reserved.
A52/A53 DTE Device
RJ45 DB9 Male
TxD 5 2 RxD
RxD 6 3 TxD
GND 7 5 GND
A52/A53 DCE Device
RJ45 DB25 Female
TxD 5 2 RxD
RxD 6 3 TxD
GND 7 7 GND
RS-422/RS-485 Pinouts
The RS-422/RS-485 port with RJ45 connector
or Terminal Block Connector is depicted as
follows.
~
~
~
~~RS-422
A52/A53
RJ45 Jack
Connector Pinouts Signals
1 TxD -(A)
2 RTS -(A)
3 RTS +(B)
4/7 SG
5 TxD +(B)
6 RxD +(B)
8 CTS +(B)
9 CTS -(A)
10 RxD -(A)
A52/A53
Terminal Block
Connector Pinouts Signals
1 TxD +(B)
2 TxD -(A)
3 RxD +(B)
4 RxD -(A)
5 SG
6 Power GND
7 VCCA (9V)
Note: Pins 6 and 7 of the Terminal Block are for
Power GND and Power Input, which is an
alternate option for power adapter. Be
careful TO NOT confuse RS-422/RS-485
GND with Power GND.
SG: Signal Ground
~
~
~
~~RS-485
A52/A53
RJ45 Jack
Connector Pinouts Signals
1 Data-(A)
4 SG
5 Data+(B)
7 SG
A52/A53
Terminal Block
Connector Pinouts Signals
1 Data+(B)
2 Data-(A)
5 SG
6 Power GND
7 VCCA 9V
Note : Pins 6 and 7 of the Terminal Block are for
Power GND and Power Input, which is an
alternate option for power adapter. Be
careful TO NOT confuse RS-422/RS-485
GND with Power GND.
SG: Signal Ground
Transio A52/53
Smart RS-232 to RS-422/485
Bi-directional Converter
Overview
Transio A52/53 is a smart RS-232 to RS-422/485
bi-directional converter, which allows one RS-232
port to be converted into an RS-422 or RS-485
port. With A52/53 you can control up to 32
devices, within 1.2 km, in a multidrop
environment.
Transio A52/53 is a Moxa Green Product. Moxa’s
Green Products satisfy the RoHS directive of the
European Parliament, and accordingly, do not
contain cadmium and cadmium compounds,
hexavalent chromium compounds, lead and lead
compounds, mercury and mercury compounds,
PBBs (polybrominated biphenyls), or PBDEs
(polybrominated diphenyl ethers).
To ease 2-wire RS-485 half-duplex control, fully
Automatic Data Direction Control (ADDC)
intelligence that requires no baud rate switch
settings is designed into each A52/53, simplifying
RS-485 software programming. Your applications
can easily manage data transmitting and receiving
via the half-duplex RS-485 port without using
additional code. Compared to other products that
require setting the clock speed manually with
switches, A52/53 lets you avoid many developing
and maintenance hassles.
To meet the high reliability required by harsh
industrial environments, all RS-422/485 signals
provide TVS protection, and ESD up to 25 KV. In
addition, A53 provides 2 KV of optical isolation
protection for all signals at the RS-422/485 end.
Features and Specifications
• Serial interface: RS-232, RS-422/485
• Port types: RS-232: RJ45;
RS-422/485: RJ45 or Terminal Block
• High speed, baud rate up to 921.6 Kbps; no
switch setting needed
• Signals:
RS-232: TxD, RxD, RTS, CTS, DTR, DSR,
DCD, GND;
RS-422: TxD+(B)/-(A), RxD+(B)/-(A),
RTS+(B)/-(A), CTS+(B)/-(A), GND;
RS-485-Data+(B)/-(A), GND
• Supports fully Automatic Data Direction
Control (ADDC) with no baud rate switch
settings for RS-485
• RS-485 data control modes: auto (ADDC) or
by RTS
• RS-422 supports CTS, RTS signals for
hardware flow control
• LED indicators for power and 4 signal states
(TxD, RxD, RTS, CTS)
• All RS-422/485 signals provide TVS
protection. (ESD 8 KV, EFT 2KV)
• All RS-422/485 signals support up to 2 KV
(DC) of optical isolation protection (A53
only)
• Provides overloading protection when there
are 2 signals shorted together at the
RS-422/485 end
• Built-in 120 ohm termination resistors for
RS-422/RS-485 (selectable with jumper by
RS-485 mode)
• Supports up to 32 units connected in an
RS-485 multidrop network
• CE approval
• 9V 1.5A UL/ TÜV 110V/230V power
adapter can support up to 4 converters
• An external power adapter is required, with
input voltage for the converter ranging from
DC +9V to +30V.
• Operating temperature: 0 to 55°C
• Dimensions: 90 x 60 x 21 mm
• Mounting Kit: Plastic Plates and screws for
mounting A52/53 on the wall or any surface.
• Power consumption: A52: 157 mA max.
(+9V); A53: 285A max. (+9V)
Applications
• Multipoint data acquisition
• Factory automation
• Remote serial device control
• Building security automation
• Critical industrial control
1 2 3 4 5 6 7
RJ45 Connector Terminal Block Connector
1 2 3 4 5 6 7 8 9 10
RJ45 Plug Pin 1
R S -4 2 2 / 4 8 5 R S -2 3 2
Mounting
Screw
Fixing Screw
RJ45 Plu
g
Pin 1
RS-422/485
R 45 Connecto rJ
Power Jack
RS-232
R 45 Connecto rJ
External Po wer Connection
RS-422/485
Ter mi n al Bl o c k
Transio A52/53 User’s Manual Transio A52/53 User’s Manual
Installation
Switch and jumper settings
To change the operation mode, remove the two
screws on top of the converter, open the cover,
and then use the array of sliding switches to set
the desired mode.
DIP switches are used to select the operation
mode (RS-422 or RS-485). For RS-485 mode,
the control mode (By RTS or ADDC) is also set
by DIP switch.
Internal view of A52/53
SW1
RS-422 mode Off
RS-485 mode On*
SW2
By RTS Off
Auto Data Direction Control (ADDC) On*
(* Default settings)
In RS-422 mode, RxD is automatically set with
a 120 ohm terminating resistor.
In RS-485 mode, the 120 ohm terminating
resistor is set by one jumper.
When shorted, the resistor is enabled.
Basic Communication Wiring
Before placing a converter in an existing
network, the converter should be properly
configured. The following diagrams show
typical layouts for both converters.
LED Indicators
LED indicators for TxD, RxD, RTS, CTS
signals and PWR are located on top of
A52/A53. The indicator light is NOT lit when
there is no signal, or the power is off.
TxD: Shows green when connected and
transmitting data from RS-232 to
RS-422/485.
RxD: Shows green when connected and
receiving data from RS-232 to
RS-422/485.
RTS: Shows green when connected and
RS-232 RTS Signal is ON.
CTS: Shows green when connected and
RS-232 CTS Signal is ON.
PWR: Shows green when power is ON.
Power supply
A52/53 converters are designed for standard
+24 VDC unregulated power for use in
industrial environments. Operation is
guaranteed when using any power supply
between +9 and +30 VDC, 350 mA.
An optional power adapter (9V 1.5A UL/TUV
110V/230V) can support up to 4 converters
(see the following diagram).
A52/53 Converter Connection Diagram
RS-232 Pinouts
The RJ45 port for the RS-232 signal is shown
in the following figure.
1 10
A52/A53 RJ45
Connector Pinouts RS-232 Signals
1 DCD Always On
2 DSR
3 RTS
4 GND
5 TxD
6 RxD
7 GND
8 CTS
9 DTR
10 –
Note: Each group of (DTR, DSR) pins are
shorted, freeing users from the hardware
flow control cable wiring problem. For
this reason, we list two types of RS-232
cable wiring below.
Type 1: To connect the RS-232 side of A52/A53 to
a DTE (e.g., PC COM1/2) or DCE (Be
sure to check the precise DTE/DCE
pinouts. The following DTE/DCE pinouts
are just an example)
A52/A53 DTE Device
RJ45 DB25 Male
DCD 1 8 DCD
DSR 2 20 DTR
RTS 3 5 CTS
GND 4 7 GND
TxD 5 3 RxD
RxD 6 2 TxD
GND 7 7 GND
CTS 8 4 RTS
DTR 9 6 DSR
A52/A53 DTE Device
RJ45 DB9 Male
DCD 1 1 DCD
DSR 2 4 DTR
RTS 3 8 CTS
GND 4 5 GND
TxD 5 2 RxD
RxD 6 3 TxD
GND 7 5 GND
CTS 8 7 RTS
DTR 9 6 DSR
A52/A53 DCE Device
RJ45 DB25 Female
DCD 1 8 DCD
DSR 2 6 DTR
RTS 3 4 CTS
GND 4 7 GND
TxD 5 2 RxD
RxD 6 3 TxD
GND 7 7 GND
CTS 8 5 RTS
DTR 9 20 DSR
Type 2: You can connect the RS-232 side of
A52/A53 to a DTE, e.g., a terminal or PC
COM1/2, with 3-pin wiring if you don't
need hardware flow control.
A52/A53 DTE Device
RJ45 DB25 Male
TxD 5 3 RxD
RxD 6 2 TxD
GND 7 7 GND
10-pin RJ45 Jack
AUTO
485
RTS
422
JP
T
X
D
R
X
D
R
T
S
C
T
S
P
W
R
RJ45 Plug Pin 1
RJ45 Plug Pin 1
RJ45 Plug Pin 1
RJ45 Plug Pin 1
Pow e r
Po we r G ND
RS-42 2/4 85 RS-4 22/48 5
RS- 23 2 PC
Po w e r
TxD(2)
RxD ( 3 )
RTS(4 )
CTS(5)
DSR(6)
GND(7)
DCD(8)
DTR(20)
RxD(2) Data + (B))
TxD(3) Data -(A)
CTS(4) GND
RTS(5)
DTR(6)
GND(7)
DCD(8)
DSR(20 )
Data+ (B)
Data
GND
-(A)
RS-232 RS- 485
Host D 25 Fe ma le
Conn ec tor
B
A52/53 Co nvert er
RS-48 5 De v ic e s
TxD(2)
RxD (3)
RTS(4 )
CTS(5)
DSR(6)
GND(7)
DCD(8)
DTR(20)
RxD(2) TxD+ (B))
TxD(3) TxD-(A)
CTS(4) RxD+ (B)
RTS(5) RxD-(A)
DTR(6) GND
GND(7)
DCD(8)
DSR(20)
RxD + (B)
TxD+ (B )
TxD-(A)
GND
RxD - ( A)
RS- 2 3 2
Ho st D 2 5 Fe male
Con ne c to r
B
A52/53 Converter
RS-4 22 De vic es

Produktspezifikationen

Marke: Moxa
Kategorie: Nicht kategorisiert
Modell: A53-DB9F

Brauchst du Hilfe?

Wenn Sie Hilfe mit Moxa A53-DB9F benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Moxa

Moxa

Moxa TCF-142-S-ST-T Bedienungsanleitung

23 August 2024
Moxa

Moxa ioLogik E2260 Bedienungsanleitung

23 August 2024
Moxa

Moxa MGate MB3170-T Bedienungsanleitung

23 August 2024
Moxa

Moxa TCC-100I-T Bedienungsanleitung

27 Juni 2024
Moxa

Moxa MGate MB3270I-T Bedienungsanleitung

27 Juni 2024
Moxa

Moxa MGate MB3270-T Bedienungsanleitung

27 Juni 2024
Moxa

Moxa MGate 5101-PBM-MN-T Bedienungsanleitung

27 Juni 2024
Moxa

Moxa MGate MB3270I Bedienungsanleitung

27 Juni 2024
Moxa

Moxa MGate MB3170I Bedienungsanleitung

27 Juni 2024
Moxa

Moxa MGate 5101-PBM-MN Bedienungsanleitung

27 Juni 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024