Moultrie Super Pro Magnum Feeder Bedienungsanleitung

Moultrie Videokamera Super Pro Magnum Feeder

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Moultrie Super Pro Magnum Feeder (3 Seiten) in der Kategorie Videokamera. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

Instructions for Super Pro Magnum Feeder

Thank you for your purchase of the Super Pro Magnum Feeder. Please read this sheet

before

operating the unit. If you should have any questions about this product or any other

Moultrie

product, please contact us using the information on the back of this sheet.

DRILLING YOUR DRUM OR BARREL

MOUNTING THE FEEDER

Turn drum over, measure and mark the center of the bottom.

Mark where holes of kit are on the bottom of the drum.

Drill three 5/16” Feeder Leg Holes.

Using a Hole Saw, drill a 2.25” hole in the center of the

bottom of your drum.

From the inside of the drum, put at washers on the 1/4-20 x 4”

Combination Drive Screws then slide through the holes in the

bottom of the barrel and screw the push nuts onto the bolts on

the outside of the barrel.

Slide feeder over three Bolts that are sticking rmly through

the bottom of the drum. Attach to the Feeder Kit Drum

using the three provided Wing Nuts.

Super Pro Magnum Kit will mount to the bottom of any drum or barrel

NOTE: If you purchased a Moultrie barrel, go to Step B

Combination Drive Screw

Qty. 3

(¼”-20 x 4”)

Flat Washer

Qty. 3

(¼”)

Push Nut

Qty. 3

(¼”)

Wing Nut

Qty. 3

(¼”)

HARDWARE INCLUDED:

Push Nut

Combination

Drive Screw

Turn grooved handle counterclockwise one click . This will release

the battery cover from the feeder kit. Battery cover can be pulled

o straight downward and set aside.

NOTE: Grooved handle

should stay assembled with battery cover.

DO NOT FORCE THE GROOVED HANDLE COUNTERCLOCKWISE

AN ADDITIONAL CLICK.

This will disassemble the grooved handle

from the battery cover and can cause wear on the parts that

retain this assembly.

Bolts

Super Pro Magnum

Feeder Kit

Wing Nuts

Drum

Flat Washer

INSTALLING BATTERY

CAUTION: WEAR EY ROE P TECTION

NOTE: Be sure that the Red and Black alligator clips labeled with a “1” are

both attached to the appropriate terminals on the rst battery, and that

the Red and Black alligator clips labeled with a “2” are both attached to

the appropriate terminals on the second battery (if used).

Make sure grooved handle is in the counterclockwise position,

then slide the battery cover back onto the assembly. Make sure

the design features line up with the features on the feeder kit.

Once fully in place, rotate the grooved handle one click in the

clockwise direction to secure all pieces in place.

NOTE: Make sure grooved handle is rotated

counter-clockwise before trying to install

battery housing or else it will not lock into place.

STAND UP FEEDER AND INSTALL LID

Assemble leg poles with the desired amount of leg sections.

Tap legs into place during assembly.

With two legs against the ground, rotate feeder upward until

vertical and supported by all three legs.

Add feed, then install lid and tighten bolt securely.

Leg Section

Leg Pole

Square Leg

Brackets

DO NOT EXCEED 400 LBS

OF FEED IN 55-GAL FEEDERS

DO NOT EXCEED 200 LBS

OF FEED IN 30-GAL FEEDERS

Install one or two 6-volt alkaline (ex. Energizer™) or Moultrie rechargeable batteries by attaching the Red Alligator Clip

to the postitive terminal (+) and the Black Alligator Clip to the negative (-) terminal.

Super Pro Magnum

Feeder Kit

Belly Band

Ring

Bolt

Spacer

Lock

Washer

Nut

NOTE: DO NOT LOAD FEEDER until it is standing up and in place (see Section D).

Belly Band

Ring

Slide the bolt through the , and Belly Band Ring Spacer

Lock Washer as shown. Tighten nut on bolt until metal

Belly Band Ring tabs are touching spacer on each side.

Turn the upside down and slide the Metal Drum Belly Band Ring

around perimeter and make sure that belly band is snug against

the bottom structure ring as shown (Moultrie barrel only).

CONFIGURING AND TESTING FEEDER

SET CURRENT TIME: Press the PROGRAM button and SET CURRENT TIME will appear. Press UP or DOWN to set the

hour, then press RIGHT to go to the minutes. Press UP or DOWN to set the minutes. Press the BACK button to return

to the Main Menu , or press PROGRAM to proceed through the settings.

NOTE: The timer is capable up to 10 feed times, each 1-60 seconds each, and each can operate on any day of

the week where each day can be toggled ON/OFF.

SET CURRENT DAY: Press the PROGRAM button until the Set Current Day screen appears. Press LEFT or RIGHT to

select the current day. Press BACK to return to the Main Menu, or press PROGRAM to proceed through the settings.

SET EST. FEED REMAINING: Press the PROGRAM button until the Est. Feed Remaining screen appears. Press UP or

DOWN to select the amount of feed you have in the feeder. Press BACK to return to the Main Menu, or press

PROGRAM to proceed through the settings.

SET FEED TIME: Press the PROGRAM button until the desired Feed Timer appears at the top of the screen. Press the

DOWN button until the feed time is ashing. Press PROGRAM to enter edit mode. Press UP or DOWN to set the hour.

Press the RIGHT button to go over to the minutes. Press UP or DOWN to set the minutes. Press PROGRAM or BACK to

return to the Feed Timer. The factory settings include two feeder times 7am and 6pm, each for 6 seconds.

SET DAYS OF THE WEEK: After setting the feed time, press UP so the days of the week start ashing. Press PROGRAM

to enter edit mode. By default all days should be enabled. Press LEFT or RIGHT to highlight the desired day. Press

DOWN to disable the selected day. Press UP to re-enable the selected day. Once all desired days are selected, press

PROGRAM or BACK to return to the Feed Timer.

SET RUN DURATION: Press DOWN and LEFT until the RUN DURATION seconds are ashing. Press PROGRAM to enter

edit mode. Press UP or DOWN to set desired feed duration. Press PROGRAM or BACK to return to the Feed Timer. 

SET MOTOR SPEED: Press UP or DOWN until the motor speed setting is ashing at the bottom of the screen. Press

PROGRAM to enter edit mode. Press RIGHT or LEFT to select the desired motor setting. Press PROGRAM or BACK to

return to the Feed Timer.

When the Feed Timer is blinking at the top of the screen, press PROGRAM or RIGHT to advance to the next feed

timer. Repeat for all required feed times.

TEST FEEDER: Press the BACK button to reach the Main Menu. Press the TEST button to enter the Test Mode. The

Test duration will appear (this will be the same as the duration as Feed Timer 1). Press UP or DOWN to set the Test

Duration. Press PROGRAM. Press RIGHT or LEFT to select desired motor speed. Press PROGRAM to perform test.

After a 5 second countdown, the test will commence. 

Full Battery

Empty Battery

09292023 / MFG-13455

Our Service Department will gladly answer any questions you have.

www.moultriefeeders.com/support

Helpful Tips:

– For extended battery life, the Moultrie 6V Feeder/Micro Camer Power Panel (MFA-15029) or Feeder PowerPanel (MFA-12602) can be added using the

External Power Port.

– Replacement parts can be purchased from Moultrie’s website www.moultriefeeders.com.

– Your Moultrie Super Pro Magnum Feeder Kit has a Lifetime Warranty. Please visit www.moultriefeeders.com/support for more information.

FCC COMPLIANCE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interf erence, and (2) this device must accept any interf erence received, including interference that

may cause undesired operation.

Changes or modications not expressly approved by PRADCO Outdoor Brands could void the user’s authorit y to operate this device.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interf erence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.