Morningstar EcoBoost MPPT Bedienungsanleitung

Morningstar Nicht kategorisiert EcoBoost MPPT

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Morningstar EcoBoost MPPT (87 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/87

Solar Charging System Controller

Installation, Operation and Maintenance Manual

www.morningstarcorp.com

EcoBoost MPPT

MAXIMUM POWER POINT TRACKING

For the most recent manual revisions, see the version at:

www.morningstarcorp.com

MODELS

EB-MPPT-20 EB-MPPT-20M

EB-MPPT-30 EB-MPPT-30M

EB-MPPT-40 EB-MPPT-40M

SPECIFICATION SUMMARY

EB-MPPT-20 EB-MPPT-30 EB-MPPT-40

Nominal Battery

Voltage 12/24V 12/24V 12/24V

Max. PV Open-

Circuit Voltage* 120V 120V 120V

Nominal Max.

InputPower** 300 / 600W 400 / 800W 560 /

1120W

Max. Battery

Charging Current 20A 30A 40A

Rated Load Current 20A 30A 30A

DIMENSIONS (centimeters)

TABLE OF

*Array voltage should never exceed this limit

**These power levels refer to the maximum wattage the EcoBoost MPPT

can process. Higher power arrays can be used without damaging the

controller.

(

14.8 )

( 17.0 )

( 19.6 )

(18.1

)

(7.1 )

.....Continued

5.0 Troubleshooting...........................................35

5.1 LED Fault Indications...................................................35

5.2 Battery Charging and Performance Issues.................39

6.0 Warranty .................................................... 40

7.0 Technical Specifications............................... 41

8.0 Certifications...............................................44

Installation 10

• Do not install in locations where water can enter the

controller.

• Loose power connections and /or corroded wires

may result in resistive connections that melt wire

insulation, burn surrounding materials, or even cause

ﬁre. Ensure tight connections and use cable clamps to

secure cables and prevent them from swaying in mobile

applications.

• Preset charging proﬁles are generally designed for

lead acid batteries. Custom settings can be used for

varied charging requirements (see sections 3.2 and 4.7

for details). Note that some battery types may not be

compatible.

• The EcoBoost MPPT battery connection may be wired

to one battery, or a bank of batteries. The following

instructions refer to a singular battery, but it is implied

that the battery connection can be made to either one

battery or a group of batteries in a battery bank.

• The EcoBoost MPPT uses self-tapping fasteners,

an anodized aluminum heat sink, and conformal

coating to protect it from harsh conditions. However,

for acceptable service life, extreme temperatures and

marine environments should be avoided.

• The EcoBoost MPPT prevents reverse current leakage at

night, so a blocking diode is not required in the system.

• The EcoBoost MPPT is designed to regulate ONLY solar

(photovoltaic) power. Connection to any other type of

power source e.g. wind turbine or generator may void

the warranty. However, other power sources can be

connected directly to the battery.

• The maximum power terminal wire size is #6 AWG /

16 mm2 (solid/multi-strand) or #8 AWG / 10 mm2 (ﬁne

strand). Use a ﬂathead insulated screwdriver, and

torque tightly up to 3.95 Nm.

• Stranded wires to be connected to the EcoBoost MPPT

terminals should be prepared ﬁrst with e.g. clamped

copper heads, etc. to avoid the possibility of one

conductor free out of the connection screw, and

possible contact with the metal enclosure.

Installation 12

Switches 2, 3: System Voltage

Three (3) system voltage conﬁgurations are available as

shown in the table below:

System Voltage Switch 2 Switch 3

Auto OFF OFF

12 OFF ON

24 ON OFF

NOTE: Before connecting the battery, measure the open-circuit

voltage. It must be over 10 volts to start the controller. If the

system voltage Settings Switches are set to Auto-detect, battery

voltage over 15.5V will be detected as a 24V nominal battery,

and the unit will charge accordingly. The 12/24V auto selection is

only done at start-up, and the detected system voltage will never

change during operation.

Generally, the specﬁc system voltage is known, and it is best

to set DIPs 2,3 accordingly; the auto-detect setting should

be used only in rare circumstances.

Switches 4, 5, 6: Battery Type Selection

Preset EcoBoost MPPT battery charging options are shown

in table 3-1 below. All voltage settings listed are for nominal

12 volt batteries.

Multiply the voltage settings by two (2) for 24 volt systems.

These settings are general guidelines for NOTE:

use at the operator’s discretion. The

EcoBoost MPPT can be programmed to satisfy a wide range

of charging parameters.

Consult the battery manufacturer for

optimal battery charge settings.

Installation 14

3.3 Mounting

Inspect the controller for shipping damage. Mount the Eco-

Boost MPPT to a vertical surface (4-#8 self-tapping screws

are included). Tighten the mounting screws, using care not

to crack the plastic case. Do not install directly over an easily

combustible surface since the heat sink may get hot under

certain operating conditions.

NOTE: The heat sink must be in a vertical position (ﬁns

up and down).

For proper air ﬂow, allow at least 15 cm (6 in) of space

above and below the controller, and 50 mm (2 in) at the

sides - see Figure 3-2 below. Install in an area protected

from direct rain and sun.

If the controller is installed in an enclosure, some

ventilation is recommended. Do not locate in an enclosure

where battery gases can accumulate.

Figure 3-2. Proper Clearances for Passive Cooling

15 cm

5 cm

Produktspezifikationen

Marke:	Morningstar
Kategorie:	Nicht kategorisiert
Modell:	EcoBoost MPPT
Breite:	196 mm
Tiefe:	71 mm
Gewicht:	1400 g
Internationale Schutzart (IP-Code):	IP20
Höhe:	173 mm
Energieschutzeigenschaften:	Overheating, Overload, Short circuit
Betriebstemperatur:	-40 - 60 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 100 %
Zertifizierung:	CE, TUV Listed: IEC 62109, EN 62109-1, Emissions 55014-1, Immunity 55014-2
Temperaturbereich bei Lagerung:	-20 - 60 °C
Ladestrom:	30 A
Ladespannung:	- V