Milwaukee TILT-LOK 6390-21 Bedienungsanleitung
Milwaukee
Sägemaschine
TILT-LOK 6390-21
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee TILT-LOK 6390-21 (32 Seiten) in der Kategorie Sägemaschine. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/32
Cat. No. / No de cat.
6390-20, 6394
HEAVY-DUTY CIRCULAR SAW WITH TILT-LOK™
ADJUSTABLE HANDLE
SCIES CIRCULAIRES INDUSTRIELLES AVEC POIGNEE
« TILT-LOK™ »
SIERRA CIRCULAR PARA TRABAJO PESADO CON
EMPUÑADURA TILT-LOK™ (INCLINABLE-FIJABLE)
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce risk
of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
• Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
• Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energizing power tools that have the switch
on invites accidents.
• Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
• Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn
it on and o. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Pow-
er tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may aect
the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
SERVICE
• Have your power tool serviced by a qualied repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SPECIFIC SAFETY RULES FOR
CIRCULAR SAW
Cutting procedures
•
DANGER
Keep hands away from cutting area
and the blade. Keep your second
hand on auxiliary handle, or motor housing. If both
hands are holding the saw, they cannot be cut by the
blade.
• Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the workpiece.
• Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
3
• Never hold the workpiece in your hands or across
your leg while cutting. Secure the workpiece to a
stable platform. It is important to support the work
properly to minimise body exposure, blade binding,
or loss of control.
• Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting tool may contact hidden wiring or its own
cord. Contact with a “live” wire will also make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
• When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
• Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the saw
will run o-centre, causing loss of control.
• Never use damaged or incorrect blade washers
or bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
Further safety instructions for all saws
Kickback causes and related warnings
– Kickback is a sudden reaction to a pinched, jammed
or misaligned saw blade, causing an uncontrolled saw
to lift up and out of the workpiece toward the operator;
– When the blade is pinched or jammed by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator;
– If the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into
the top surface of the wood causing the blade to climb
out of the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below:
• Maintain a rm grip with both hands on the saw and
position your arms to resist kickback forces. Posi-
tion your body to either side of the blade, but not
in line with the blade. Kickback could cause the saw
to jump backwards, but kickback forces can be con-
trolled by the operator, if proper precautions are taken.
• When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes
to a complete stop. Never attempt to remove the
saw from the work or pull the saw backward while
the blade is in motion or kickback may occur. In-
vestigate and take corrective actions to eliminate the
cause of blade binding.
• When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are
not engaged into the material. If saw blade is binding,
it may walk up or kickback from the workpiece as the
saw is restarted.
• Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag
under their own weight. Supports must be placed under
the panel on both sides, near the line of cut and near
the edge of the panel.
• Do not use dull or damaged blades. Unsharpened
or improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback.
• Blade depth and bevel adjusting locking levers must
be tight and secure before making cut. If blade adjust-
ment shifts while cutting, it may cause binding and kickback.
• Use extra caution when sawing into existing walls
or other blind areas. The protruding blade may cut
objects that can cause kickback.
Lower guard function
• Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does
not move freely and close instantly. Never clamp or
tie the lower guard into the open position. If saw is
accidentally dropped, lower guard may be bent. Raise
the lower guard with the retracting handle and make
sure it moves freely and does not touch the blade or
any other part, in all angles and depths of cut.
• Check the operation of the lower guard spring. If
the guard and the spring are not operating properly,
they must be serviced before use. Lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
• The lower guard may be retracted manually only for
special cuts such as “plunge cuts” and “compound
cuts”. Raise the lower guard by the retracting han-
dle and as soon as the blade enters the material, the
lower guard must be released. For all other sawing,
the lower guard should operate automatically.
• Always observe that the lower guard is covering
the blade before placing saw down on bench or
oor. An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade to stop after
switch is released.
•
WARNING
To reduce the risk of injury in ap-
plications that produce a consider-
able amount of dust, use an OSHA compliant dust
extraction solution in accordance with the solu-
tion’s operating instructions.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SPECIFICATIONS
Amps ...................................................................15
No Load RPM ..................................................6300
Blade Size ..................................................... 7-1/4"
Arbor ................................................................. 5/8"
Depth of Cut at 90° ............................. 0 to 2-15/32"
Depth of Cut at 45° ............................. 0 to 1-13/16"
Cat. No. 6390-20 .....................................................
Volts .......................................................120 AC/DC
Cat. No. 6394 ...........................................................
Volts .................................................... 120 AC Only
Produktspezifikationen
| Marke: | Milwaukee |
| Kategorie: | Sägemaschine |
| Modell: | TILT-LOK 6390-21 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Milwaukee TILT-LOK 6390-21 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Sägemaschine Milwaukee
6 Oktober 2024
3 Oktober 2024
17 September 2024
15 September 2024
14 September 2024
12 September 2024
6 September 2024
5 September 2024
4 September 2024
1 September 2024
Bedienungsanleitung Sägemaschine
- Sägemaschine Brennenstuhl
- Sägemaschine Cotech
- Sägemaschine Makita
- Sägemaschine Royal Catering
- Sägemaschine Bosch
- Sägemaschine Flex
- Sägemaschine Parkside
- Sägemaschine Vonroc
- Sägemaschine AEG
- Sägemaschine Black And Decker
- Sägemaschine Cocraft
- Sägemaschine FERM
- Sägemaschine Ryobi
- Sägemaschine Skil
- Sägemaschine Topcraft
- Sägemaschine Trotec
- Sägemaschine Maestro
- Sägemaschine Prime3
- Sägemaschine Hilti
- Sägemaschine Bort
- Sägemaschine DeWalt
- Sägemaschine Einhell
- Sägemaschine Elu
- Sägemaschine Festool
- Sägemaschine Mafell
- Sägemaschine Maktec
- Sägemaschine Worx
- Sägemaschine Luxor
- Sägemaschine Tacklife
- Sägemaschine Hikoki
- Sägemaschine Hitachi
- Sägemaschine Hyundai
- Sägemaschine Fuxtec
- Sägemaschine Kress
- Sägemaschine Max
- Sägemaschine Metabo
- Sägemaschine Stanley
- Sägemaschine Atika
- Sägemaschine Güde
- Sägemaschine Power Craft
- Sägemaschine Scheppach
- Sägemaschine Workzone
- Sägemaschine Biltema
- Sägemaschine Meec Tools
- Sägemaschine Dremel
- Sägemaschine Fieldmann
- Sägemaschine King Craft
- Sägemaschine Proxxon
- Sägemaschine Westfalia
- Sägemaschine Remington
- Sägemaschine Husqvarna
- Sägemaschine Stihl
- Sägemaschine Dedra
- Sägemaschine DURO
- Sägemaschine Graphite
- Sägemaschine Pattfield
- Sägemaschine Silverline
- Sägemaschine Holzmann
- Sägemaschine MSW
- Sägemaschine Florabest
- Sägemaschine Germania
- Sägemaschine Stiga
- Sägemaschine Hammer
- Sägemaschine ACG
- Sägemaschine Greenworks
- Sägemaschine Huvema
- Sägemaschine Robust
- Sägemaschine Zipper
- Sägemaschine Yato
- Sägemaschine Baumr-AG
- Sägemaschine Genesis
- Sägemaschine BluCave
- Sägemaschine Morrison
- Sägemaschine Batavia
- Sägemaschine Evolution
- Sägemaschine Matrix
- Sägemaschine Dolmar
- Sägemaschine Bavaria
- Sägemaschine Brüder Mannesmann
- Sägemaschine Narex
- Sägemaschine Toolcraft
- Sägemaschine Fein
- Sägemaschine AL-KO
- Sägemaschine EGO
- Sägemaschine CMI
- Sägemaschine IDEAL
- Sägemaschine Cobra
- Sägemaschine Verto
- Sägemaschine Craftsman
- Sägemaschine Powerplus
- Sägemaschine Alpha Tools
- Sägemaschine Echo
- Sägemaschine Elektra Beckum
- Sägemaschine Toledo
- Sägemaschine McCulloch
- Sägemaschine Ozito
- Sägemaschine Yard Force
- Sägemaschine Sun Joe
- Sägemaschine Solo
- Sägemaschine Texas
- Sägemaschine Oregon Scientific
- Sägemaschine Ridgid
- Sägemaschine Porter-Cable
- Sägemaschine VARO
- Sägemaschine Spear & Jackson
- Sägemaschine Duro Pro
- Sägemaschine Erbauer
- Sägemaschine Ergofix
- Sägemaschine Exakt
- Sägemaschine Ferrex
- Sägemaschine FOM
- Sägemaschine Gamma
- Sägemaschine Gardenline
- Sägemaschine Global
- Sägemaschine Goon
- Sägemaschine Grizzly
- Sägemaschine Gude Pro
- Sägemaschine HURRICANE
- Sägemaschine Kompernass
- Sägemaschine Lux Tools
- Sägemaschine Max Bahr
- Sägemaschine Maxx
- Sägemaschine Qualcast
- Sägemaschine Tanaka
- Sägemaschine Toolson
- Sägemaschine Troy-Bilt
- Sägemaschine Avantco
- Sägemaschine Wolfcraft
- Sägemaschine Masport
- Sägemaschine Garland
- Sägemaschine Meister Craft
- Sägemaschine Clarke
- Sägemaschine Powerworks
- Sägemaschine Sovereign
- Sägemaschine Challenge
- Sägemaschine Challenge Xtreme
- Sägemaschine Truper
- Sägemaschine Łucznik
- Sägemaschine Vulcan
- Sägemaschine MacAllister
- Sägemaschine RIKON
- Sägemaschine Backyard Pro Butcher Series
- Sägemaschine Kreg
- Sägemaschine Jonsered
- Sägemaschine Einhell Bavaria
- Sägemaschine Proviel
- Sägemaschine Budget
- Sägemaschine Tryton
- Sägemaschine MTM
- Sägemaschine EFA
- Sägemaschine MyTool
- Sägemaschine McKenzie
- Sägemaschine Anova
- Sägemaschine Yellow Garden Line
- Sägemaschine Ergotools Pattfield
- Sägemaschine IKRA
- Sägemaschine FIXIT
- Sägemaschine Bestgreen
- Sägemaschine BGU
- Sägemaschine Power Smart
- Sägemaschine Ultranatura
- Sägemaschine TAURUS Titanium
- Sägemaschine Maxbear
- Sägemaschine Extralink
- Sägemaschine Stalco
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
14 Oktober 2024
12 Oktober 2024
12 Oktober 2024
11 Oktober 2024