Milwaukee M18 Fuel 2784-22 Bedienungsanleitung
Milwaukee
Schleifmaschine
M18 Fuel 2784-22
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee M18 Fuel 2784-22 (20 Seiten) in der Kategorie Schleifmaschine. Dieser Bedienungsanleitung war für 32 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/20
Cat. No. / No de cat.
2784-20
M18â„¢ FUELâ„¢ DIE GRINDER
MEULE À RECTIFIER LES MATRICES FUEL™ M18™
AMOLADORA RECTA DE M18â„¢ FUELâ„¢
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and speciîš¿ca-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, îš¿re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiîš¿ed plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your îš¿nger on
the switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
• Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of îš¿re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and îš¿re.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
3
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a îš¿re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Do not use a battery pack or tool that is dam-
aged or modiîš¿ed. Damaged or modiîš¿ed batteries
may exhibit unpredictable behavior resulting in îš¿re,
explosion or risk of injury.
• Do not expose a battery pack or tool to re or
excessive temperature. Exposure to îš¿re or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range speciîš¿ed in the instructions. Charging
improperly or at temperatures outside the speciîš¿ed
range may damage the battery and increase the risk
of îš¿re.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
DIE GRINDERS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, Polishing, Carving or Abrasive
Cutting-Off Operations:
• This power tool is intended to function as a
grinder, sander, wire brush, polisher, carving
or cut-off tool. Read all safety warnings,
instructions, illustrations and speciîš¿cations
provided with this power tool. Failure to follow
all instructions listed below may result in electric
shock, îš¿re and/or serious injury.
• Do not use accessories which are not specically
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
• The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and y apart.
• The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately controlled.
• The arbour size of wheels, sanding drum or any
other accessory must properly îš¿t the spindle or
collet of the power tool. Accessories that do not
match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may
cause loss of control.
• Mandrel mounted wheels, sanding drums,
cutters or other accessories must be fully
inserted into the collet or chuck. If the mandrel is
insufîš¿ciently held and/or the overhang of the wheel
is too long, the mounted wheel may become loose
and ejected at high velocity.
• Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, sanding drum
for cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or acces-
sory is dropped, inspect for damage or install
an undamaged accessory. After inspecting and
installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum
no-load speed for one minute. Damaged acces-
sories will normally break apart during this test time.
• Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping ying debris generated by various opera-
tions. The dust mask or respirator must be capable
of îš¿ltrating particles generated by your operation.
Prolonged exposure to high intensity noise may
cause hearing loss.
• Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may y away and
cause injury beyond immediate area of operation.
• Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
• Always hold the tool rmly in your hands during
the start-up. The reaction torque of the motor, as it
accelerates to full speed, can cause the tool to twist.
• Use clamps to support workpiece whenever
practical. Never hold a small workpiece in one
hand and the tool in the other hand while in use.
Clamping a small workpiece allows you to use both
hands to control the tool. Round material such as
dowel rods, pipes or tubing have a tendency to roll
while being cut, and may cause the bit to bind or
jump toward you.
• Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
• After changing the bits or making any adjust-
ments, make sure the collet nut, chuck or any
other adjustment devices are securely tightened.
Loose adjustment devices can unexpectedly shift,
causing loss of control, loose rotating components
will be violently thrown.
• Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the ac-
cessory into your body.
• Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
• Do not operate the power tool near ammable
materials. Sparks could ignite these materials.
• Do not use accessories that require liquid cool-
ants. Using water or other liquid coolants may result
in electrocution or shock.
Produktspezifikationen
Marke: | Milwaukee |
Kategorie: | Schleifmaschine |
Modell: | M18 Fuel 2784-22 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Milwaukee M18 Fuel 2784-22 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schleifmaschine Milwaukee
5 Oktober 2024
3 Oktober 2024
22 September 2024
16 September 2024
2 September 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
Bedienungsanleitung Schleifmaschine
- Schleifmaschine SilverCrest
- Schleifmaschine Cotech
- Schleifmaschine Makita
- Schleifmaschine Bosch
- Schleifmaschine Flex
- Schleifmaschine Parkside
- Schleifmaschine Vonroc
- Schleifmaschine AEG
- Schleifmaschine Gorenje
- Schleifmaschine Mesko
- Schleifmaschine Black And Decker
- Schleifmaschine Cocraft
- Schleifmaschine FERM
- Schleifmaschine Ryobi
- Schleifmaschine Skil
- Schleifmaschine Topcraft
- Schleifmaschine Trotec
- Schleifmaschine Maestro
- Schleifmaschine Eibenstock
- Schleifmaschine Hilti
- Schleifmaschine Bort
- Schleifmaschine DeWalt
- Schleifmaschine Einhell
- Schleifmaschine Elu
- Schleifmaschine Festool
- Schleifmaschine Maktec
- Schleifmaschine Worx
- Schleifmaschine Nuova Simonelli
- Schleifmaschine Hikoki
- Schleifmaschine Hitachi
- Schleifmaschine Hyundai
- Schleifmaschine Hazet
- Schleifmaschine Kress
- Schleifmaschine Max
- Schleifmaschine Metabo
- Schleifmaschine Stanley
- Schleifmaschine Güde
- Schleifmaschine Scheppach
- Schleifmaschine Workzone
- Schleifmaschine United Office
- Schleifmaschine Meec Tools
- Schleifmaschine AquaPur
- Schleifmaschine Dremel
- Schleifmaschine Fieldmann
- Schleifmaschine Proxxon
- Schleifmaschine Westfalia
- Schleifmaschine Profitec
- Schleifmaschine DURO
- Schleifmaschine Graphite
- Schleifmaschine Pattfield
- Schleifmaschine Silverline
- Schleifmaschine Holzmann
- Schleifmaschine Florabest
- Schleifmaschine Aerotec
- Schleifmaschine Huvema
- Schleifmaschine Stomer
- Schleifmaschine Yato
- Schleifmaschine Baumr-AG
- Schleifmaschine Genesis
- Schleifmaschine ABB
- Schleifmaschine Batavia
- Schleifmaschine Dolmar
- Schleifmaschine Bavaria
- Schleifmaschine Brüder Mannesmann
- Schleifmaschine Toolcraft
- Schleifmaschine Fein
- Schleifmaschine Craftsman
- Schleifmaschine Defort
- Schleifmaschine Powerplus
- Schleifmaschine Alpha Tools
- Schleifmaschine Ozito
- Schleifmaschine Kawasaki
- Schleifmaschine Solo
- Schleifmaschine Ridgid
- Schleifmaschine Porter-Cable
- Schleifmaschine Dolmar(Makita)
- Schleifmaschine Duro Pro
- Schleifmaschine Ergofix
- Schleifmaschine Gamma
- Schleifmaschine Global
- Schleifmaschine Goon
- Schleifmaschine Gude Pro
- Schleifmaschine Tanaka
- Schleifmaschine Bunn
- Schleifmaschine Neo
- Schleifmaschine Meister Craft
- Schleifmaschine Malmbergs
- Schleifmaschine Yamato
- Schleifmaschine Truper
- Schleifmaschine Victoria Arduino
- Schleifmaschine RIKON
- Schleifmaschine Einhell Bavaria
- Schleifmaschine Proviel
- Schleifmaschine Budget
- Schleifmaschine McKenzie
- Schleifmaschine Kwb
- Schleifmaschine Ergotools Pattfield
- Schleifmaschine FIXIT
- Schleifmaschine THUN
- Schleifmaschine Rodcraft
- Schleifmaschine Bavaria By Einhell
- Schleifmaschine ATI-ZDL
- Schleifmaschine Gladiator
- Schleifmaschine Handwerk
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
14 Oktober 2024
13 Oktober 2024
8 Oktober 2024
7 Oktober 2024
3 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024
29 September 2024