Milwaukee 6147-31 Bedienungsanleitung

Milwaukee Schleifmaschine 6147-31

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee 6147-31 (19 Seiten) in der Kategorie Schleifmaschine. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/19

HEAVY-DUTY SANDERS/GRINDERS

EXTRA ROBUSTE PONCEUSE-RECTIFIEUSE

LIJADORAS/ESMERILADORAS HEAVY-DUTY

Cat. No.

No de cat.

6117-30

6117-31

6117-31B

6117-33

6117-33D

6121-30

6121-31

6121-31A

6124-30

6124-31

6146-30

6146-31

6146-33

6147-30

6147-31

6161-30

6161-31

6161-33

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

SPECIFIC SAFETY RULES or its own cord. Cutting accessory contacting a

"live" wire may make exposed metal parts of the

power tool "live" and shock the operator.

• Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled into

the spinning accessory.

• Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the power

tool out of your control.

• Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

• Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal

may cause electrical hazards.

• Do not operate the power tool near ﬂ ammable

materials. Sparks could ignite these materials.

• Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in

the direction opposite of the accessory’s rotation

at the point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into

the surface of the material causing the wheel to

climb out or kick out. The wheel may either jump

toward or away from the operator, depending on

direction of the wheel’s movement at the point of

pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

• Maintain a ﬁ rm grip on the power tool and posi-

tion your body and arm to allow you to resist

kickback forces. Always use auxiliary handle,

if provided, for maximum control over kickback

or torque reaction during start-up. The operator

can control torque reactions or kickback forces, if

proper precautions are taken.

• Never place your hand near the rotating acces-

sory. Accessory may kick back over your hand.

• Do not position your body in the area where

power tool will move if kickback occurs. Kick-

back will propel the tool in direction opposite to

the wheel’s movement at the point of snagging.

• Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

• Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create fre-

quent kickback and loss of control.

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or

serious injury. Save all warnings and instructions for future reference

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

POWER TOOL USE AND CARE

SERVICE

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

these devices can reduce dust-related hazards.

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and oﬀ. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc., in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations diﬀerent from those intended could

result in a hazardous situation.

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂ uence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

Safety Warnings Common for Grinding, Sand-

ing, Wire Brushing or Abrasive Cutting-Off

Operations:

• This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations

and speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, ﬁ re and/or serious injury.

• Operations such as polishing are not recom-

mended to be performed with this power tool. Op-

erations for which the power tool was not designed

may create a hazard and cause personal injury.

• Do not use accessories which are not speciﬁ -

cally designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

• The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and ﬂ y apart.

• The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

• The arbour size of wheels, ﬂ anges, backing

pads or any other accessory must properly

ﬁ t the spindle of the power tool. Accessories

with arbour holes that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

• Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or acces-

sory is dropped, inspect for damage or install

an undamaged accessory. After inspecting and

installing an accessory, position yourself and

bystanders away from the plane of the rotating

accessory and run the power tool at maximum

no-load speed for one minute. Damaged acces-

sories will normally break apart during this test time.

• Wear personal protective equipment. Depend-

ing on application, use face shield, safety

goggles or safety glasses. As appropriate,

wear dust mask, hearing protectors, gloves

and work shop apron capable of stopping

small abrasive or workpiece fragments. The

eye protection must be capable of stopping ﬂ ying

debris generated by various operations. The dust

mask or respirator must be capable of ﬁ ltrating

particles generated by your operation. Prolonged

exposure to high intensity noise may cause hear-

ing loss.

• Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken accessory

may ﬂ y away and cause injury beyond immediate

area of operation.

• Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring

1. Side handle

2. Spindle lock

3. Side handle socket

4. Paddle switch

5. Switch lock-on

6. Switch lock-oﬀ

7. Type 27 guard

8. Guard lock lever

9. Trigger switch

10.Slide switch

Safety Warnings Specific for Grinding and

Abrasive Cutting-Oﬀ Operations:

• Use only wheel types that are recommended

for your power tool and the speciﬁ c guard

designed for the selected wheel. Wheels for

which the power tool was not designed can not

be adequately guarded and are unsafe.

• The guard must be securely attached to the

power tool and positioned for maximum safety,

so the least amount of wheel is exposed to-

wards the operator. The guard helps to protect

operator from broken wheel fragments and ac-

cidental contact with wheel.

• Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-off wheel. Abrasive cut-off wheels are

intended for peripheral grinding, side forces applied

to these wheels may cause them to shatter.

• Always use undamaged wheel ﬂ anges that are

of correct size and shape for your selected

wheel. Proper wheel ﬂ anges support the wheel

thus reducing the possibility of wheel breakage.

Flanges for cut-oﬀ wheels may be different from

grinding wheel ﬂ anges.

• Do not use worn down wheels from larger

power tools. Wheel intended for larger power tool

is not suitable for the higher speed of a smaller

tool and may burst.

Additional Safety Warnings Speciﬁ c for Abra-

sive Cutting-Oﬀ Operations:

• Do not "jam" the cut-off wheel or apply ex-

cessive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibility

of kickback or wheel breakage.

• Do not position your body in line with and

behind the rotating wheel. When the wheel, at

the point of operation, is moving away from your

body, the possible kickback may propel the spin-

ning wheel and the power tool directly at you.

• When wheel is binding or when interrupting a

cut for any reason, switch oﬀ the power tool

and hold the power tool motionless until the

wheel comes to a complete stop. Never attempt

to remove the cut-oﬀ wheel from the cut while

the wheel is in motion otherwise kickback may

occur. Investigate and take corrective action to

eliminate the cause of wheel binding.

• Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully reenter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted

in the workpiece.

• Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

• Use extra caution when making a "pocketcut"

into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes, elec-

trical wiring or objects that can cause kickback.

Safety Warnings Speciﬁ c for Sanding Operations:

• Do not use excessively oversized sanding disc

paper. Follow manufacturers recommenda-

tions, when selecting sanding paper. Larger

sanding paper extending beyond the sanding

pad presents a laceration hazard and may cause

snagging, tearing of the disc or kickback.

Safety Warnings Speciﬁ c for Wire Brushing

Operations:

• Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not

over stress the wires by applying excessive

load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

• If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

or brush may expand in diameter due to workload

and centrifugal forces.

Additional Safety Warnings

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

10 5

Double Insulated

Volts Alternating Current

Volts Alternating Current /

Direct Current

Amps

Revolutions per Minute (RPM)

Underwriters Laboratories, Inc.

United States and Canada

Mexican Approvals Marking

FUNCTIONAL DESCRIPTION

SYMBOLOGY

SPECIFICATIONS

Cat. No. Volts Amps RPM Spindle

Thread Size Wheel

Size Switch

Type Lock-On Guard

Type Speed

Dial

6117-30

6117-31

6117-31B

6117-33

6117-33D

6121-30

6121-31

6121-31A

6124-30

6124-31

6146-30

6146-31

6146-33

6147-30

6147-31

6161-30

6161-31

6161-33

120 AC

120 AC/DC

120 AC

11,000

2,800-11,000

11,000

9,000

11,000

9,000

5/8"-11

4½"

Paddle

Slide

Trigger

Paddle

Slide

Paddle

Slide

Yes

Type 27

Type 1

Yes

outlet (See Figure A). If the tool should electrically

malfunction or break down, grounding provides a

low resistance path to carry electricity away from

the user, reducing the risk of electric shock.

The grounding prong in the plug is connected

through the green wire inside the cord to the

grounding system in the tool. The green wire in the

cord must be the only wire connected to the tool's

grounding system and must never be attached to an

electrically "live" terminal.

Your tool must be plugged into

an appropriate outlet, properly

installed and grounded in ac-

cordance with all codes and

ordinances. The plug and outlet

should look like those in Figure A. Fig. A

GROUNDING

WARNING Improperly connecting the

grounding wire can result in the risk of

electric shock. Check with a qualiﬁ ed electri-

cian if you are in doubt as to whether the

outlet is properly grounded. Do not modify

the plug provided with the tool. Never remove

the grounding prong from the plug. Do not

use the tool if the cord or plug is damaged. If

damaged, have it repaired by a MILWAUKEE

service facility before use. If the plug will not

ﬁ t the outlet, have a proper outlet installed by

a qualiﬁ ed electrician.

Grounded Tools: Tools with Three Prong Plugs

Tools marked "Grounding Required" have a three

wire cord and three prong grounding plug. The

plug must be connected to a properly grounded

Produktspezifikationen

Marke:	Milwaukee
Kategorie:	Schleifmaschine
Modell:	6147-31

Brauchst du Hilfe?

Wenn Sie Hilfe mit Milwaukee 6147-31 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Schleifmaschine Milwaukee

Milwaukee 0725-21 Bedienungsanleitung

5 Oktober 2024

Milwaukee 2784-20 Bedienungsanleitung

3 Oktober 2024

Milwaukee 6121-31 Bedienungsanleitung

22 September 2024

Milwaukee 6147-31 Bedienungsanleitung

16 September 2024

Milwaukee 5192 Bedienungsanleitung

2 September 2024

Milwaukee AGV 17-180 XC DMS Bedienungsanleitung

31 August 2024

Milwaukee AP 12 E Bedienungsanleitung

31 August 2024

Milwaukee AGV 17-125 INOX Bedienungsanleitung

31 August 2024

Milwaukee AP 14-2 200E Bedienungsanleitung

31 August 2024

Milwaukee C12 RT Bedienungsanleitung

31 August 2024

Bedienungsanleitung Schleifmaschine

Neueste Bedienungsanleitung für -Kategorien-

Makita GA9060R Bedienungsanleitung

15 Oktober 2024

Hitachi G 13SR Bedienungsanleitung

14 Oktober 2024

Makita DGA700Z Bedienungsanleitung

13 Oktober 2024

Metabo WP820-115 Bedienungsanleitung

8 Oktober 2024

DeWalt DW887N Bedienungsanleitung

7 Oktober 2024

Makita GA013GD101 Bedienungsanleitung

3 Oktober 2024

Ryobi RAG800-115 Bedienungsanleitung

2 Oktober 2024

Makita GA022GD202 Bedienungsanleitung

2 Oktober 2024

Hilti GDG 6-A22 Bedienungsanleitung

30 September 2024

Black And Decker KG2300 Bedienungsanleitung

29 September 2024