Milwaukee 5192 Bedienungsanleitung

Milwaukee Schleifmaschine 5192

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee 5192 (20 Seiten) in der Kategorie Schleifmaschine. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/20

Cat. No. / No de cat.

5192, 5194, 5196

HEAVY-DUTY DIE GRINDERS

EXTRA ROBUSTE RECTIFIEUSES POUR MATRICES

HEAVY DUTY RECTIFICADOR DE MATRICES

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING

Read all safety warnings, instruc-

tions, illustrations and specica-

tions provided with this power tool. Failure to

follow all instructions listed below may result in

electric shock, re and/or serious injury. Save all

warnings and instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-oper-

ated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

•

Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Un-

modied plugs and matching outlets will reduce risk

of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electric shock.

• Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

• When operating a power tool outdoors, use an ex-

tension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of an GFCI reduces

the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not

use a power tool while you are tired or under the

inuence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result

in serious personal injury.

• Use personal protective equipment. Always wear

eye protection. Protective equipment such as a dust

mask, non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your nger on the

switch or energizing power tools that have the switch

on invites accidents.

• Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a ro-

tating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewelry. Keep your hair and clothing away from

moving parts. Loose clothes, jewelry or long hair can

be caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust col-

lection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do no

t force the power tool. Use the correct power tool

for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting

the power tool accidentally.

• Store

idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Pow-

er tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a hazard-

ous situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

SERVICE

• Have your power tool serviced by a qualied repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES FOR

DIE GRINDERS

Safety Warnings Common for Grinding, Sanding,

Wire Brushing, Polishing, Carving or Abrasive

Cutting-Off Operations:

• This power tool is intended to function as a grinder,

sander, wire brush, polisher, carving or cut-off tool.

• Do not use accessories which are not specically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to

your power tool, it does not assure safe operation.

• The rated speed of the accessories must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and y apart.

• The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories cannot

be adequately controlled.

• The arbour size of wheels, sanding drum or any

other accessory must properly t the spindle or

collet of the power tool. Accessories that do not

match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause

loss of control.

• Mandrel mounted wheels, sanding drums, cutters

or other accessories must be fully inserted into the

collet or chuck. If the mandrel is insufciently held and/

or the overhang of the wheel is too long, the mounted

wheel may become loose and ejected at high velocity.

• Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, sanding drum for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of the

rotating accessory and run the power tool at maxi-

mum no-load speed for one minute. Damaged ac-

cessories will normally break apart during this test time.

• Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of

stopping ying debris generated by various operations.

The dust mask or respirator must be capable of ltrating

particles generated by your operation. Prolonged ex-

posure to high intensity noise may cause hearing loss.

• Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of work-

piece or of a broken accessory may y away and cause

injury beyond immediate area of operation.

• Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or

its own cord. Cutting accessory contacting a "live"

wire may make exposed metal parts of the power tool

"live" and could give the operator an electric shock.

• Always hold the tool rmly in your hands during

the start-up. The reaction torque of the motor, as it

accelerates to full speed, can cause the tool to twist.

• Use clamps to support workpiece whenever practi-

cal. Never hold a small workpiece in one hand and

the tool in the other hand while in use. Clamping

a small workpiece allows you to use your hand(s) to

control the tool. Round material such as dowel rods,

pipes or tubing have a tendency to roll while being cut,

and may cause the bit to bind or jump toward you.

• Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinning accessory.

• Never lay the power tool down until the accessory

has come to a complete stop. The spinning acces-

sory may grab the surface and pull the power tool out

of your control.

• After changing the bits or making any adjustments,

make sure the collet nut, chuck or any other adjust-

ment devices are securely tightened. Loose adjust-

ment devices can unexpectedly shift, causing loss of

control, loose rotating components will be violently

thrown.

• Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

your body.

• Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

• Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

• Do not use accessories that require liquid cool-

ants. Using water or other liquid coolants may result

in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, sanding band, brush or any other acces-

sory. Pinching or snagging causes rapid stalling of the

rotating accessory which in turn causes the uncontrolled

power tool to be forced in the direction opposite of the

accessory’s rotation. For example, if an abrasive wheel

is snagged or pinched by the workpiece, the edge of the

wheel that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb out

or kick out. The wheel may either jump toward or away

from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels

may also break under these conditions. Kickback is the

result of power tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking

proper precautions as given below.

• Maintain a rm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. The operator can control kickback forces, if

proper precautions are taken.

• Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the ac-

cessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause

loss of control or kickback.

• Do not attach a toothed saw blade. Such blades

create frequent kickback and loss of control.

• Always feed the bit into the material in the same

direction as the cutting edge is exiting from the

material (which is the same direction as the chips

are thrown). Feeding the tool in the wrong direction

causes the cutting edge of the bit to climb out of the

work and pull the tool in the direction of this feed.

• When using rotary les, cut-off wheels, high-speed

cutters or tungsten carbide cutters, always have

the work securely clamped. These wheels will grab

if they become slightly canted in the groove, and can

kickback. When a cut-off wheel grabs, the wheel itself

usually breaks. When the steel saw, high-speed cutters

or tungsten carbide cutter grab, it may jump from the

groove and you could lose control of the tool.

Safety Warnings Specic for Grinding and Abrasive

Cutting-Off Operations:

• Use only wheel types that are recommended for

your power tool and only for recommended appli-

cations. For example: do not grind with the side of

a cut-off wheel. Abrasive cut-off wheels are intended

for peripheral grinding, side forces applied to these

wheels may cause them to shatter.

• For threaded abrasive cones and plugs use only

undamaged wheel mandrels with an unrelieved

shoulder ange that are of correct size and length.

Proper mandrels will reduce the possibility of breakage.

• Do not “jam” a cut-off wheel or apply excessive pres-

sure. Do not attempt to make an excessive depth of

cut. Overstressing the wheel increases the loading and

susceptibility to twisting or snagging of the wheel in the

cut and the possibility of kickback or wheel breakage.

Produktspezifikationen

Marke:	Milwaukee
Kategorie:	Schleifmaschine
Modell:	5192

Brauchst du Hilfe?

Wenn Sie Hilfe mit Milwaukee 5192 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Schleifmaschine Milwaukee

Milwaukee 0725-21 Bedienungsanleitung

5 Oktober 2024

Milwaukee 2784-20 Bedienungsanleitung

3 Oktober 2024

Milwaukee 6121-31 Bedienungsanleitung

22 September 2024

Milwaukee 6147-31 Bedienungsanleitung

16 September 2024

Milwaukee 5192 Bedienungsanleitung

2 September 2024

Milwaukee AGV 17-180 XC DMS Bedienungsanleitung

31 August 2024

Milwaukee AP 12 E Bedienungsanleitung

31 August 2024

Milwaukee AGV 17-125 INOX Bedienungsanleitung

31 August 2024

Milwaukee AP 14-2 200E Bedienungsanleitung

31 August 2024

Milwaukee C12 RT Bedienungsanleitung

31 August 2024

Bedienungsanleitung Schleifmaschine

Neueste Bedienungsanleitung für -Kategorien-

Makita GA9060R Bedienungsanleitung

15 Oktober 2024

Hitachi G 13SR Bedienungsanleitung

14 Oktober 2024

Makita DGA700Z Bedienungsanleitung

13 Oktober 2024

Metabo WP820-115 Bedienungsanleitung

8 Oktober 2024

DeWalt DW887N Bedienungsanleitung

7 Oktober 2024

Makita GA013GD101 Bedienungsanleitung

3 Oktober 2024

Ryobi RAG800-115 Bedienungsanleitung

2 Oktober 2024

Makita GA022GD202 Bedienungsanleitung

2 Oktober 2024

Hilti GDG 6-A22 Bedienungsanleitung

30 September 2024

Black And Decker KG2300 Bedienungsanleitung

29 September 2024