Milwaukee 6391-21 Bedienungsanleitung
Milwaukee
Sägemaschine
6391-21
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee 6391-21 (32 Seiten) in der Kategorie Sägemaschine. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/32
Cat. No. / No de cat.
6391
HEAVY DUTY LEFT BLADE CIRCULAR SAW WITH TILT-LOK™
HANDLE
ROBUSTE SCIE CIRCULAIRE À POIGNÉE TILT-LOK™ ET LAME
À GAUCHE
SIERRA CIRCULAR DE CUCHILLA IZQUIERDA PARA TRABAJO
PESADO CON EMPUÑADURA TILT-LOKTM (INCLINABLE-FIJABLE)
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on
the switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
• Do not use the power tool if the switch does not
turn it on and o. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may aect the power tool’s operation. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations dierent from those intended could
result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
3
SPECIFIC SAFETY RULES FOR
LEFT BLADE CIRCULAR SAWS
Cutting procedures
•
DANGER
Keep hands away from cutting area
and the blade. Keep your second
hand on auxiliary handle, or motor housing. If
both hands are holding the saw, they cannot be cut
by the blade.
• Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece.
• Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
• Never hold the workpiece in your hands or
across your leg while cutting. Secure the work-
piece to a stable platform. It is important to support
the work properly to minimise body exposure, blade
binding, or loss of control.
• Hold the power tool by insulated gripping sur-
faces only, when performing an operation where
the cutting tool may contact hidden wiring or its
own cord. Contact with a “live” wire will also make
exposed metal parts of the power tool “live” and
could give the operator an electric shock.
• When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
• Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the saw
will run o-centre, causing loss of control.
• Never use damaged or incorrect blade washers
or bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance
and safety of operation.
Further safety instructions for all saws
Kickback causes and related warnings
– Kickback is a sudden reaction to a pinched,
jammed or misaligned saw blade, causing an un-
controlled saw to lift up and out of the workpiece
toward the operator;
– When the blade is pinched or jammed by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the
operator;
– If the blade becomes twisted or misaligned in the
cut, the teeth at the back edge of the blade can dig
into the top surface of the wood causing the blade
to climb out of the kerf and jump back toward the
operator.
Kickback is the result of saw misuse and/or incor-
rect operating procedures or conditions and can be
avoided by taking proper precautions as given below:
• Maintain a rm grip with both hands on the saw
and position your arms to resist kickback forces.
Position your body to either side of the blade, but
not in line with the blade. Kickback could cause
the saw to jump backwards, but kickback forces can
be controlled by the operator, if proper precautions
are taken.
• When blade is binding, or when interrupting a
cut for any reason, release the trigger and hold
the saw motionless in the material until the
blade comes to a complete stop. Never attempt
to remove the saw from the work or pull the saw
backward while the blade is in motion or kick-
back may occur. Investigate and take corrective
actions to eliminate the cause of blade binding.
• When restarting a saw in the workpiece, centre
the saw blade in the kerf so that saw teeth are
not engaged into the material. If saw blade binds,
it may walk up or kickback from the workpiece as
the saw is restarted.
• Support large panels to minimise the risk of
blade pinching and kickback. Large panels tend
to sag under their own weight. Supports must be
placed under the panel on both sides, near the line
of cut and near the edge of the panel.
• Do not use dull or damaged blades. Unsharpened
or improperly set blades produce narrow kerf caus-
ing excessive friction, blade binding and kickback.
• Blade depth and bevel adjusting locking levers
must be tight and secure before making cut. If
blade adjustment shifts while cutting, it may cause
binding and kickback.
• Use extra caution when sawing into existing
walls or other blind areas. The protruding blade
may cut objects that can cause kickback.
Lower guard function
• Check lower guard for proper closing before
each use. Do not operate the saw if lower guard
does not move freely and close instantly. Never
clamp or tie the lower guard into the open posi-
tion. If saw is accidentally dropped, lower guard may
be bent. Raise the lower guard with the retracting
handle and make sure it moves freely and does not
touch the blade or any other part, in all angles and
depths of cut.
• Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use.
Lower guard may operate sluggishly due to dam-
aged parts, gummy deposits, or a build-up of debris.
• The lower guard may be retracted manually
only for special cuts such as “plunge cuts”
and “compound cuts”. Raise the lower guard
by the retracting handle and as soon as the
blade enters the material, the lower guard must
be released. For all other sawing, the lower guard
should operate automatically.
• Always observe that the lower guard is covering
the blade before placing saw down on bench or
oor. An unprotected, coasting blade will cause
the saw to walk backwards, cutting whatever is in
its path. Be aware of the time it takes for the blade
to stop after switch is released.
•
WARNING
To reduce the risk of injury in ap-
plications that produce a consid-
erable amount of dust, use an OSHA compliant
dust extraction solution in accordance with the
solution’s operating instructions.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
Produktspezifikationen
| Marke: | Milwaukee |
| Kategorie: | Sägemaschine |
| Modell: | 6391-21 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Milwaukee 6391-21 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Sägemaschine Milwaukee
6 Oktober 2024
3 Oktober 2024
17 September 2024
15 September 2024
14 September 2024
12 September 2024
6 September 2024
5 September 2024
4 September 2024
1 September 2024
Bedienungsanleitung Sägemaschine
- Sägemaschine Brennenstuhl
- Sägemaschine Cotech
- Sägemaschine Makita
- Sägemaschine Royal Catering
- Sägemaschine Bosch
- Sägemaschine Flex
- Sägemaschine Parkside
- Sägemaschine Vonroc
- Sägemaschine AEG
- Sägemaschine Black And Decker
- Sägemaschine Cocraft
- Sägemaschine FERM
- Sägemaschine Ryobi
- Sägemaschine Skil
- Sägemaschine Topcraft
- Sägemaschine Trotec
- Sägemaschine Maestro
- Sägemaschine Prime3
- Sägemaschine Hilti
- Sägemaschine Bort
- Sägemaschine DeWalt
- Sägemaschine Einhell
- Sägemaschine Elu
- Sägemaschine Festool
- Sägemaschine Mafell
- Sägemaschine Maktec
- Sägemaschine Worx
- Sägemaschine Luxor
- Sägemaschine Tacklife
- Sägemaschine Hikoki
- Sägemaschine Hitachi
- Sägemaschine Hyundai
- Sägemaschine Fuxtec
- Sägemaschine Kress
- Sägemaschine Max
- Sägemaschine Metabo
- Sägemaschine Stanley
- Sägemaschine Atika
- Sägemaschine Güde
- Sägemaschine Power Craft
- Sägemaschine Scheppach
- Sägemaschine Workzone
- Sägemaschine Biltema
- Sägemaschine Meec Tools
- Sägemaschine Dremel
- Sägemaschine Fieldmann
- Sägemaschine King Craft
- Sägemaschine Proxxon
- Sägemaschine Westfalia
- Sägemaschine Remington
- Sägemaschine Husqvarna
- Sägemaschine Stihl
- Sägemaschine Dedra
- Sägemaschine DURO
- Sägemaschine Graphite
- Sägemaschine Pattfield
- Sägemaschine Silverline
- Sägemaschine Holzmann
- Sägemaschine MSW
- Sägemaschine Florabest
- Sägemaschine Germania
- Sägemaschine Stiga
- Sägemaschine Hammer
- Sägemaschine ACG
- Sägemaschine Greenworks
- Sägemaschine Huvema
- Sägemaschine Robust
- Sägemaschine Zipper
- Sägemaschine Yato
- Sägemaschine Baumr-AG
- Sägemaschine Genesis
- Sägemaschine BluCave
- Sägemaschine Morrison
- Sägemaschine Batavia
- Sägemaschine Evolution
- Sägemaschine Matrix
- Sägemaschine Dolmar
- Sägemaschine Bavaria
- Sägemaschine Brüder Mannesmann
- Sägemaschine Narex
- Sägemaschine Toolcraft
- Sägemaschine Fein
- Sägemaschine AL-KO
- Sägemaschine EGO
- Sägemaschine CMI
- Sägemaschine IDEAL
- Sägemaschine Cobra
- Sägemaschine Verto
- Sägemaschine Craftsman
- Sägemaschine Powerplus
- Sägemaschine Alpha Tools
- Sägemaschine Echo
- Sägemaschine Elektra Beckum
- Sägemaschine Toledo
- Sägemaschine McCulloch
- Sägemaschine Ozito
- Sägemaschine Yard Force
- Sägemaschine Sun Joe
- Sägemaschine Solo
- Sägemaschine Texas
- Sägemaschine Oregon Scientific
- Sägemaschine Ridgid
- Sägemaschine Porter-Cable
- Sägemaschine VARO
- Sägemaschine Spear & Jackson
- Sägemaschine Duro Pro
- Sägemaschine Erbauer
- Sägemaschine Ergofix
- Sägemaschine Exakt
- Sägemaschine Ferrex
- Sägemaschine FOM
- Sägemaschine Gamma
- Sägemaschine Gardenline
- Sägemaschine Global
- Sägemaschine Goon
- Sägemaschine Grizzly
- Sägemaschine Gude Pro
- Sägemaschine HURRICANE
- Sägemaschine Kompernass
- Sägemaschine Lux Tools
- Sägemaschine Max Bahr
- Sägemaschine Maxx
- Sägemaschine Qualcast
- Sägemaschine Tanaka
- Sägemaschine Toolson
- Sägemaschine Troy-Bilt
- Sägemaschine Avantco
- Sägemaschine Wolfcraft
- Sägemaschine Masport
- Sägemaschine Garland
- Sägemaschine Meister Craft
- Sägemaschine Clarke
- Sägemaschine Powerworks
- Sägemaschine Sovereign
- Sägemaschine Challenge
- Sägemaschine Challenge Xtreme
- Sägemaschine Truper
- Sägemaschine Łucznik
- Sägemaschine Vulcan
- Sägemaschine MacAllister
- Sägemaschine RIKON
- Sägemaschine Backyard Pro Butcher Series
- Sägemaschine Kreg
- Sägemaschine Jonsered
- Sägemaschine Einhell Bavaria
- Sägemaschine Proviel
- Sägemaschine Budget
- Sägemaschine Tryton
- Sägemaschine MTM
- Sägemaschine EFA
- Sägemaschine MyTool
- Sägemaschine McKenzie
- Sägemaschine Anova
- Sägemaschine Yellow Garden Line
- Sägemaschine Ergotools Pattfield
- Sägemaschine IKRA
- Sägemaschine FIXIT
- Sägemaschine Bestgreen
- Sägemaschine BGU
- Sägemaschine Power Smart
- Sägemaschine Ultranatura
- Sägemaschine TAURUS Titanium
- Sägemaschine Maxbear
- Sägemaschine Extralink
- Sägemaschine Stalco
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
14 Oktober 2024
12 Oktober 2024
12 Oktober 2024
11 Oktober 2024