Milwaukee 6140-830 Bedienungsanleitung
Milwaukee
Schleifmaschine
6140-830
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee 6140-830 (21 Seiten) in der Kategorie Schleifmaschine. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/21
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE MANUEL DE
L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL DEL
OPERADOR.
HEAVY-DUTY SANDERS/GRINDERS
EXTRA ROBUSTE PONCEUSE-RECTIFIEUSE
LIJADORAS/ESMERILADORAS HEAVY-DUTY
Cat. No.
No de cat.
6122-30
6122-30A
6122-31
6122-31A
6140-30
6140-33
6148-30
6148-31
6148-33
6116-30,
6116-31,
6116-33,
6160-30,
6160-31,
6160-33,
6123-30,
6123-31
23
SPECIFIC SAFETY RULES Prolonged exposure to high intensity noise may
cause hearing loss.
• Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken accessory
may fl y away and cause injury beyond immediate
area of operation.
• Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting a
live wire may make exposed metal parts of the
power tool live and shock the operator.
• Position the cord clear of the spinning acces-
sory. If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled into
the spinning accessory.
• Never lay the power tool down until the ac-
cessory has come to a complete stop. The
spinning accessory may grab the surface and pull
the power tool out of your control.
• Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
• Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
• Do not operate the power tool near fl ammable
materials. Sparks could ignite these materials.
• Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in
the direction opposite of the accessory’s rotation
at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into
the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump
toward or away from the operator, depending on
direction of the wheel’s movement at the point of
pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
• Maintain a fi rm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can control torque reactions or
kickback forces, if proper precautions are taken.
Safety Warnings Common for Grinding, Sand-
ing, Wire Brushing or Abrasive Cutting-Off
Operations:
• This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool.
Read all safety warnings, instructions, il-
lustrations and specifi cations provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fi re and/
or serious injury.
• Operations such as polishing are not recom-
mended to be performed with this power tool.
Operations for which the power tool was not de-
signed may create a hazard and cause personal
injury.
• Do not use accessories which are not specifi -
cally designed and recommended by the tool
manufacturer. Just because the accessory can
be attached to your power tool, it does not assure
safe operation.
• The rated speed of the accessory must be at
least equal to the maximum speed marked
on the power tool. Accessories running
faster than their rated speed can break and
fl y apart.
• The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
• The arbour size of wheels, fl anges, backing
pads or any other accessory must properly
fi t the spindle of the power tool. Accessories
with arbour holes that do not match the mounting
hardware of the power tool will run out of bal-
ance, vibrate excessively and may cause loss of
control.
• Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or acces-
sory is dropped, inspect for damage or install
an undamaged accessory. After inspecting
and installing an accessory, position yourself
and bystanders away from the plane of the
rotating accessory and run the power tool
at maximum no-load speed for one minute.
Damaged accessories will normally break apart
during this test time.
• Wear personal protective equipment. Depend-
ing on application, use face shield, safety
goggles or safety glasses. As appropriate,
wear dust mask, hearing protectors, gloves
and work shop apron capable of stopping
small abrasive or workpiece fragments. The
eye protection must be capable of stopping
fl ying debris generated by various operations.
The dust mask or respirator must be capable of
fi ltrating particles generated by your operation.
PERSONAL SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WORK AREA SAFETY
ELECTRICAL SAFETY
WARNING READ ALL SAFETY WARNINGS AND INSTRUCTIONS.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or
serious injury. Save all warnings and instructions for future reference
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
POWER TOOL USE AND CARE
SERVICE
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of fl ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodifi ed plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
• If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
• Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
• Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
• Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
• Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc., in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
• Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the infl uence of drugs, alcohol or medi-
cation. A moment of inattention while operating
power tools may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your fi nger on the switch or energising power
tools that have the switch on invites accidents.
45
1. Side handle
2. Spindle lock
3. Switch lock-on (Cat.No. 6116-30, 6122-30, 6122-30A, 6123-30, 6140-30, 6148-30, 6160-30)
4. Switch lock-off (Cat.No. 6116-30, 6116-31, 6140-30, 6148-30, 6148-31, 6160-30, 6160-31)
5. Paddle switch (Cat.No. 6116-30, 6116-31, 6140-30, 6148-30, 6148-31, 6160-30, 6160-31)
6. Side handle sockets
7. Guard lock lever
8. Type 27 guard
9. Trigger switch
(Cat.No. 6122-30,
6122-30A, 6122-31,
6122-31A, 6123-30,
6123-31)
10. Slide switch (Cat.No. 6116-33,
6140-33, 6148-33, 6160-33)
• Never place your hand near the rotating acces-
sory. Accessory may kick back over your hand.
• Do not position your body in the area where
power tool will move if kickback occurs. Kick-
back will propel the tool in direction opposite to
the wheel’s movement at the point of snagging.
• Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
• Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create fre-
quent kickback and loss of control.
Safety Warnings Specific for Grinding and
Abrasive Cutting-Off Operations:
• Use only wheel types that are recommended
for your power tool and the specifi c guard
designed for the selected wheel. Wheels for
which the power tool was not designed can not
be adequately guarded and are unsafe.
• The guard must be securely attached to the
power tool and positioned for maximum
safety, so the least amount of wheel is ex-
posed towards the operator. The guard helps
to protect operator from broken wheel fragments
and accidental contact with wheel.
• Wheels must be used only for recommended
applications. For example: do not grind with the
side of cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces applied
to these wheels may cause them to shatter.
• Always use undamaged wheel fl anges that are
of correct size and shape for your selected
wheel. Proper wheel fl anges support the wheel
thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from
grinding wheel fl anges.
• Do not use worn down wheels from larger
power tools. Wheel intended for larger power tool
is not suitable for the higher speed of a smaller
tool and may burst.
Additional Safety Warnings Specifi c for Abra-
sive Cutting-Off Operations:
• Do not jam the cut-off wheel or apply exces-
sive pressure. Do not attempt to make an
excessive depth of cut. Overstressing the wheel
increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibil-
ity of kickback or wheel breakage.
• Do not position your body in line with and
behind the rotating wheel. When the wheel, at
the point of operation, is moving away from your
body, the possible kickback may propel the spin-
ning wheel and the power tool directly at you.
• When wheel is binding or when interrupting
a cut for any reason, switch off the power
tool and hold the power tool motionless until
the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the
cut while the wheel is in motion otherwise
kickback may occur. Investigate and take cor-
rective action to eliminate the cause of wheel
binding.
• Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully reenter the cut. The wheel may bind,
walk up or kickback if the power tool is restarted
in the workpiece.
• Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kick-
back. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
• Use extra caution when making a "pocketcut"
into existing walls or other blind areas. The
protruding wheel may cut gas or water pipes, elec-
trical wiring or objects that can cause kickback.
Safety Warnings Specifi c for Sanding Opera-
tions:
• Do not use excessively oversized sanding disc
paper. Follow manufacturers recommenda-
tions, when selecting sanding paper. Larger
sanding paper extending beyond the sanding
pad presents a laceration hazard and may cause
snagging, tearing of the disc or kickback.
Safety Warnings Specifi c for Wire Brushing
Operations:
• Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
over stress the wires by applying excessive
load to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
• If the use of a guard is recommended for wire
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel
or brush may expand in diameter due to workload
and centrifugal forces.
Additional Safety Warnings
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
• WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to fi lter out microscopic par-
ticles.
1
4
5
6
FUNCTIONAL DESCRIPTION
8
7
3
9
10 3
2
Specifi cations
Double Insulated
Volts Alternating Current
Amps
No Load Revolutions per
Minute (RPM)
Underwriters Laboratories, Inc.
United States and Canada
Mexican Approvals Marking
Cat.
No.
Volts
AC
Amps No Load
RPM
Spindle
Thread Size
Wheel
Size
6122-30
6122-30A
6122-31
6122-31A
6140-30
6140-33
6148-30
6148-31
6148-33
6116-30
6116-31
6116-33
6160-30
6160-31
6160-33
6123-30
6123-31
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
10
10
10
10
7.5
7
10
10
10
12
12
12
12
12
12
12
12
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
9,000
9,000
9,000
9,000
9,000
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
5/8"-11
4½"
5"
4½"
5"
4½"
4½"
4½"
4½"
4½"
4½"/5"
4½"/5"
4½"/5"
6"
6"
6"
5"/6"
5"/6"
Symbology
Produktspezifikationen
| Marke: | Milwaukee |
| Kategorie: | Schleifmaschine |
| Modell: | 6140-830 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Milwaukee 6140-830 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schleifmaschine Milwaukee
5 Oktober 2024
3 Oktober 2024
22 September 2024
16 September 2024
2 September 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
Bedienungsanleitung Schleifmaschine
- Schleifmaschine SilverCrest
- Schleifmaschine Cotech
- Schleifmaschine Makita
- Schleifmaschine Bosch
- Schleifmaschine Flex
- Schleifmaschine Parkside
- Schleifmaschine Vonroc
- Schleifmaschine AEG
- Schleifmaschine Gorenje
- Schleifmaschine Mesko
- Schleifmaschine Black And Decker
- Schleifmaschine Cocraft
- Schleifmaschine FERM
- Schleifmaschine Ryobi
- Schleifmaschine Skil
- Schleifmaschine Topcraft
- Schleifmaschine Trotec
- Schleifmaschine Maestro
- Schleifmaschine Eibenstock
- Schleifmaschine Hilti
- Schleifmaschine Bort
- Schleifmaschine DeWalt
- Schleifmaschine Einhell
- Schleifmaschine Elu
- Schleifmaschine Festool
- Schleifmaschine Maktec
- Schleifmaschine Worx
- Schleifmaschine Nuova Simonelli
- Schleifmaschine Hikoki
- Schleifmaschine Hitachi
- Schleifmaschine Hyundai
- Schleifmaschine Hazet
- Schleifmaschine Kress
- Schleifmaschine Max
- Schleifmaschine Metabo
- Schleifmaschine Stanley
- Schleifmaschine Güde
- Schleifmaschine Scheppach
- Schleifmaschine Workzone
- Schleifmaschine United Office
- Schleifmaschine Meec Tools
- Schleifmaschine AquaPur
- Schleifmaschine Dremel
- Schleifmaschine Fieldmann
- Schleifmaschine King Craft
- Schleifmaschine Proxxon
- Schleifmaschine Westfalia
- Schleifmaschine Profitec
- Schleifmaschine Dedra
- Schleifmaschine DURO
- Schleifmaschine Graphite
- Schleifmaschine Pattfield
- Schleifmaschine Silverline
- Schleifmaschine Holzmann
- Schleifmaschine Florabest
- Schleifmaschine Herkules
- Schleifmaschine Aerotec
- Schleifmaschine Huvema
- Schleifmaschine Stomer
- Schleifmaschine Yato
- Schleifmaschine Baumr-AG
- Schleifmaschine Genesis
- Schleifmaschine ABB
- Schleifmaschine Batavia
- Schleifmaschine Dolmar
- Schleifmaschine Bavaria
- Schleifmaschine Brüder Mannesmann
- Schleifmaschine Toolcraft
- Schleifmaschine Fein
- Schleifmaschine Powertec
- Schleifmaschine Craftsman
- Schleifmaschine Defort
- Schleifmaschine Powerplus
- Schleifmaschine Alpha Tools
- Schleifmaschine Ozito
- Schleifmaschine Kawasaki
- Schleifmaschine Solo
- Schleifmaschine Ridgid
- Schleifmaschine Porter-Cable
- Schleifmaschine Dolmar(Makita)
- Schleifmaschine Duro Pro
- Schleifmaschine Ergofix
- Schleifmaschine Felisatti
- Schleifmaschine Gamma
- Schleifmaschine Global
- Schleifmaschine Goon
- Schleifmaschine Gude Pro
- Schleifmaschine Tanaka
- Schleifmaschine Bunn
- Schleifmaschine Neo
- Schleifmaschine Meister Craft
- Schleifmaschine Malmbergs
- Schleifmaschine Yamato
- Schleifmaschine Truper
- Schleifmaschine Victoria Arduino
- Schleifmaschine RIKON
- Schleifmaschine Einhell Bavaria
- Schleifmaschine Proviel
- Schleifmaschine Budget
- Schleifmaschine McKenzie
- Schleifmaschine Kwb
- Schleifmaschine Ergotools Pattfield
- Schleifmaschine FIXIT
- Schleifmaschine THUN
- Schleifmaschine Rodcraft
- Schleifmaschine Bavaria By Einhell
- Schleifmaschine ATI-ZDL
- Schleifmaschine Gladiator
- Schleifmaschine Handwerk
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
14 Oktober 2024
13 Oktober 2024
8 Oktober 2024
7 Oktober 2024
3 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024
29 September 2024