Mikrotik netPower 16P Bedienungsanleitung

Mikrotik Nicht kategorisiert netPower 16P

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Mikrotik netPower 16P (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

netPower 16P

netPower 16PnetPower 16P

netPower 16P (CRS318-16P-2S+OUT)

The netPower is a weatherproof switch with the capability of delivering PoE to your connected devices.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.

Quickstart

Please follow these quick steps to set up your device:

Open the bottom lid (see " ");Bottom Lid

Connect all served devices to Ethernet ports;

Connect the device to the power source (see " ");Powering

Once connected to the same network, open in your web browser to start configuration, user name: a and there is no https://192.168.88.1

dmin

password by default ; (or, for some models, check user and wireless passwords on the sticker)

Once connected configure the device, so it has an active Internet connection ;https://mt.lv/configuration

Upgrade the RouterOS software to the latest version ;https://mt.lv/upgrade

Set up your router password in the bottom field of the QuickSet menu, to the right and repeat it, it will be used to login next time.

Expansion slots and ports

DC power connector 48 – 57 V.

DC power connector 18 – 30 V.

LED indicating a power state of the device.

Reset button.

Gigabit Ethernet, 8 - ports, delivering PoE out.

Two - 10G SFP+ ports.

LED Indicating the activity of SFP port.

LED Indicating the speed of SFP port.

Configuration

The device can be discovered using Winbox utility, by clicking on the Neighbors list. The default management address is 192.168.88.1. To reach both

devices needs to be in the same IP network. Configured as a bridge, ARP, and fast forward enabled. RSTP protocol activated.

RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to

the possibilities: .https://mt.lv/help

For recovery purposes, it is possible to boot the device for reinstallation, see section .Buttons and Jumpers

Powering

The device accepts power in the two ways following ways:

Direct-input power jack 1, (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 18-30 V DC.

Direct-input power jack 2, 48-57 V DC .

Use included DC plug to connect with your power source:

DC plug 2.1x5.5x12 mm to Screw Terminal 2pin.

Connect your power source cables to the two pins and secure them in place by tightening screws.

Connect DC plug to the device.

The power consumption under maximum load can reach 21 W, with attachments 325 W.

Power output

The device supports 802.3af/at PoE from Ethernet 1 - 16. You can power Mikrotik devices which supports powering through Ethernet. The power delivered

through the PoE port will depend on the incoming to the device.

Max PoE-out on low (<30 V) voltage 5.6 A (2.8 A per 8port group, max 1.1 A per port).

Max PoE-out on high (>30 V) voltage 2.8 A (1.4 A per 8port group, max 0.6 A per port).

Connecting to a PoE Adapter, only to deliver power to other devices:

Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter.

Connect an Ethernet cable from your local network (LAN) to the PoE adapter.

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

Bottom Lid

Bottom lid is secured in place with the captive screw, it can be unscrewed by hand, but do not remove the screw completely.

Pull the cover towards.

Lift to access Ethernet ports.

Mounting

The device can be mounted in several ways: pole, wall, or ceiling. The package also includes a drill hole template with detailed mounting instructions, to

help you with the drill hole marking. The device has eight mounting points for versatility use zip ties or steel clamps for mounting on the pole.

When using both the high and low Voltage adapters, the netPower will automatically choose the correct PoE standard and Voltage, based on

the devices you connect to each port. This can also be specified manually.

The IP rating scale for this device is IP54. When mounting outdoors, please ensure that any cable openings are directed downwards.

Produktspezifikationen

Marke:	Mikrotik
Kategorie:	Nicht kategorisiert
Modell:	netPower 16P
Prozessortaktfrequenz:	800 MHz
Breite:	212 mm
Tiefe:	78 mm
Produktfarbe:	Weiß
Höhe:	303 mm
DC input Spannung:	18 - 57 V
Betriebstemperatur:	-40 - 70 °C
Netzstandard:	IEEE 802.3af, IEEE 802.3at
Zertifizierung:	CE/RED, EAC, RoHS
Power over Ethernet (PoE):	Ja
Stromverbrauch (max.):	316 W
Anzahl der basisschaltenden RJ-45 Ethernet Ports:	16
Basic Switching RJ-45 Ethernet Ports-Typ:	Gigabit Ethernet (10/100/1000)
Netzstecker:	DC-Anschluss
10G-Unterstützung:	Nein
MAC-Adressentabelle:	- Eintragungen
Routing-/Switching-Kapazität:	72 Gbit/s
Rack-Einbau:	Nein
Prozessor:	98DX226S
Speicherkapazität:	256 MB
Eingebauter Prozessor:	Ja
Flash-Speicher:	16 MB
Stapelbar:	Nein
Netzteil enthalten:	Ja
Transferrate:	53.6 Mpps
Switch-Ebene:	L2/L3
Temperatursensor:	Ja
Anzahl Power over Ethernet (PoE) Anschlüsse:	16
Menge Modul-Steckplätze SFP+:	2