Mikrotik LHG LTE kit Bedienungsanleitung

Mikrotik TV-Signalverstärker LHG LTE kit

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Mikrotik LHG LTE kit (4 Seiten) in der Kategorie TV-Signalverstärker. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

LHG LTE kit

Assembly

Attach the two legs to the LHG case by sliding them onto the respective sides (when looking at the logo, leg

marked R is for the right side, leg marked L is for the left side). Snap the assembled LHG unit to the grid in the

appropriate central location. Fix the two legs in place with two self thread screws (included, use Phillips screw

driver PH2). The package also contains a grounding cable connector and a 5 degree angle adapter, for easier up or

downward tilt adjustment.

Quick start

1. While holding the unit by it’s central column, apply force to the tab, which holds the latch closed,

until the latch pops open.

2. Connect an ethernet cable to the ethernet port, connect the other end of the ethernet cable

to the included PoE injector.

3. Plug the PoE injector into your network switch or ISP internet outlet.

4. Plug the included power supply into the PoE injector to start up the device.

Powering

The device can be powered from 12-57 V 802.3af/at sources and also Passive PoE injectors (one power supply

and PoE injector are included).

Mounting

Slide the included metallic mounting rings into the two slots on the back of the antenna dish. Attach the unit to a

pole, with the Ethernet cable pointing downward. Use a PH2 screwdriver to tighten the rings. Fix the Ethernet cable

to the pole less than one meter from the unit, to avoid the cable being pulled out of the port. Optional: if required,

before mounting the unit, you can insert the included 5 degree adjustment adapter into the top or bottom slot where

the mounting ring is inserted. This will create an additional upward or downward angle, when the unit is tightened to

a vertical pole. Warning! This equipment should be installed and operated with minimum distance of 120 cm

between the radiator and your body,

Expansion slots and ports

One 10/100 ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X). Either straight

or crossover cable can be used for connecting to other network devices. The ethernet port accepts 9-30 V

DC powering from a passive PoE injector.

miniPCIe slot and SIM slot (can’t be used separately) to be used with a 3G/4G/LTE modem (the LTE kit

includes the modem already inside the device).

Buttons and jumpers

RouterBOOT reset button has the following functions. Press the button and apply the power, then:

Release the button when green LED starts flashing, to reset RouterOS configuration to defaults.

Release the button when the LED turns solid green to clear all configuration and defaults.

Release the button after LED is no longer lit (~20 seconds) to cause device to look for Netinstall servers

(required for reinstalling RouterOS over network).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed

before power is applied to the device. Useful for RouterBOOT debugging and recovery.

The device includes a grounding connection behind the ethernet port door, which you should connect to the

grounding installation of the tower or building where the device will be used. This is to substantially reduce risk of

ESD and lightning damage.

See mikrotik.com for more information. Document #41960 Modified on: 07/03/18

Configuration

We recommend clicking the “Check for updates” button and updating your RouterOS software to the latest version

to ensure the best performance and stability. RouterOS includes many configuration options in addition to what is

described in this document. We suggest to visit the RouterOS documentation page to get yourself accustomed to

the possibilities: http://mt.lv/help.

In case IP connection is not available, the Winbox tool (http://mt.lv/winbox) can be used to connect to the MAC

address of the device from the LAN side (all access is blocked from the internet port by default).

It is possible to boot the device from network, for reinstalling RouterOS for recovery purposes. This can be done

from the Ethernet port. See above how to do this.

Operating system support

The device supports RouterOS software with the version number at or above what is indicated in the RouterOS

menu . Other operating systems have not been tested. /system resource

Opening the case

To access the miniPCIe modem, opening of the unit is required. As an opening tool you can use a large size flat

head screwdriver or a small coin. Be extremely cautious when opening, because incorrect opening of the clip can

break it off! Follow these steps:

See mikrotik.com for more information. Document #41960 Modified on: 07/03/18

Follow this order when opening the unit Insert a screwdriver into the first slot

Turn the screwdriver, until one side pops open.

Continue in the above order.

Lift cover to access the card.

Federal communication commission interference statement

R11e-LTE: FCC ID TV7R11ELTE, TV7R11E4G

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.This device and its antenna must not be co-located or operation in

conjunction with any other antenna or transmitter.

IMPORTANT: Exposure to Radio Frequency Radiation. 20 cm minimum distance has to be maintained between the

antenna and user. Under such configuration, the FCC radiation exposure limits set forth for an

population/uncontrolled environment can be satisfied.

Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in

the United States (or where FCC rules apply); only those antennas certified with the product are used. The use of

any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47

part 15.204. The installer should configure the output power level of antennas, according to country regulations and

per antenna type. Professional installation is required of equipment with connectors to ensure compliance with

health and safety issues.

See mikrotik.com for more information. Document #41960 Modified on: 07/03/18

Produktspezifikationen

Marke:	Mikrotik
Kategorie:	TV-Signalverstärker
Modell:	LHG LTE kit
WLAN:	Nein
Breite:	391 mm
Tiefe:	227 mm
Mitgelieferte Kabel:	AC
Produktfarbe:	Weiß
Höhe:	391 mm
Energiequelle:	PoE
Betriebstemperatur:	-40 - 60 °C
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Typ:	Mobilfunksignalverstärker für den Außenbereich
Ethernet LAN Datentransferraten:	10, 100 Mbit/s
Antenne Zunahmeniveau (max):	21 dBi
Eingangsspannung:	12-57 V
Reset-Knopf:	Ja
Datennetzwerk:	LTE
Unterstützte UMTS-Bandbreiten:	700,850,1700,1900 MHz
Uplink-Frequenzbereich:	- MHz
Downlink-Frequenzbereich:	- MHz
Uplink Gewinn:	- dB
Ethernet/LAN:	Ja